Gage Bilt GB704SH Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Tools
  5. GB704SH
  6. Manual

Gage Bilt GB704SH Manual

Installation tool
Hide thumbs Also See for GB704SH:
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1089 AND ABOVE
GB704SH
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB704SH and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gage Bilt GB704SH

Summary of Contents for Gage Bilt GB704SH

  • Page 1 S/N: 1089 AND ABOVE GB704SH PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Description Page Warnings ..................................3 Principle of Operation and How to use the GB704SH ..................4 Description, Hydraulic Thread Preparation and Maintenance ................5 Filling and Bleeding ..............................6 Troubleshooting................................7 Overhaul ..................................8 Disassembly and Parts Lists ..........................9-10 DEXRON ® III Oil Safety Data ..........................11 Nose Assembly Selection Chart...........................

  • Page 3: Warnings

    It is recommended operator wear a suitable gloves WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 4: Principle Of Operation And How To Use The Gb704Sh

    Always disconnect air supply when tool is not in use to prevent accidental start-up. ASSEMBLY CYLINDER HEAD DEFLECTOR RIVET WORK ACTUATOR SHIPPING ASSY PLUG Image may not reflect actual tool QUICK DISCONNECT FITTING GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: Description, Hydraulic Thread Preparation And Maintenance

    The GB704SH series riveters operate on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. At 90 psi (6.2 bar) air pressure, the GB704SH series does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute.

  • Page 6: Filling And Bleeding

    With the actuator lever assy (704343) released, check dimension (A). Holding actuator lever assy (704343) check dimension (B). Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 5-6. .740 (18.8mm) .140 (3.6mm) GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 7: Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Overhaul

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or rear of tool when installing fastener.

  • Page 9: Disassembly And Parts Lists

    (400061) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). 204304 - SWIVEL ASSEMBLY 401080 - BACK-UP RING 403764 - O'RING GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 10 NOTE: Valve spring installation tool (744151) will facilitate the proper installation of the spring (744144), valve sleeve (744138) can be pulled out using valve sleeve removal tool (744152). GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 11: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations GB704SH S/N: 1089 AND ABOVE Rev 3/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Nose Assembly Selection Chart

    GS8-715-40OS (1) BACS53B1EA1/2 CHERRYMAX® and MBC® are registered trademarks of Cherry Aerospace Fasteners. GAGE BILT CERTIFIES THE GB704 WILL INSTALL THE ABOVE FASTENERS 1) 715 SERIES NOSE ASSEMBLIES REQUIRE 704001 ADAPTER. 2) INSTALLS 1/8", 5/32", AND 3/16" DIAMETERS 3) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN ONE PULL 4) FRONT END EJECTING NOSE ASSEMBLY.

  • Page 13: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB704 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.

Table of Contents