Winco HPS6000HE/I Installation And Operator's Manual
Bi-fuel generator
Hide thumbs
Also See for HPS6000HE/I:
- Installation and operator's manual (20 pages) ,
- Installation & operator's manual (20 pages) ,
- Installation instructions (4 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Winco HPS6000HE/I
Summary of Contents for Winco HPS6000HE/I
- Page 1 HPS6000HE/I INSTALLATION AND OPERATORS MANUAL BI-FUEL GENERATOR...
-
Page 2: Table Of Contents
Should you experience a problem please follow the “Troubleshooting Tables” near the end of this MODEL HPS6000HE/I manual. The warranty listed in the manual describes what you can expect from WINCO should you need SERIAL NUMBER_________________________ service assistance in the future. PURCHASE DATE_________________________ TABLE OF CONTENTS... -
Page 3: Safety Information
b. Keep fuel containers out of reach of children. SAFETY INFORMATION c. Do not smoke or use open fl ame near the generator set or fuel tank. This engine generator set has been designed and d. Keep a fi re extinguisher nearby and know its manufactured to allow safe, reliable performance. -
Page 4: Unit Capabilities
TESTING POLICY UNIT CAPABILITIES Before any generator is shipped from the factory, it GENERATOR CONNECTIONS is fully checked for performance. The generator is loaded to its full capacity, and the voltage, current HPS6000HE - 120 volt and 240 volt receptacles and frequency are carefully checked. -
Page 5: Preparing The Unit
rests with you when a generator set is sent F.O.B. load, such as an air compressor, it will require more shipping point. Only you can legally fi le a claim. starting current. If it is connected to a light load, or no load such as a power saw, it will require less 2. -
Page 6: Ng Installation
NG FUEL INSTALLATION Use 4-stroke motor oil that meets or exceeds the requirements for API service classification SJ or later (or equivalent). Always check the API service label on the oil container to be sure it includes the The information in this instruction is offered to assist letters SJ or later (or equivalent). -
Page 7: Fuel Line Sizing
12 volt DC valve is available through your local an inadequate or incorrect fuel pressure. Power and Winco dealer and can be used to shut the fuel off performance of the engine is in direct relation to the during normal periods of operation without having to correctness of the fuel system. -
Page 8: Changing Fuel Types
CHANGING FUEL TYPES These engine generator sets are designed to run on two different fuels; gasoline, and natural gas. They may be easily changed from one fuel to another. FROM GASOLINE TO NG 1. With the engine running turn off the gasoline fuel valve. -
Page 9: Initial Start Up
OIL ALERT SYSTEM This WINCO generator is equipped with a low oil shutdown system. This engine uses an fl oat switch NOTE - There is a second fuel valve under the fuel mounted inside the engine. -
Page 10: Electric Starting (Gasoline)
3. Move the choke lever to the “CLOSED” position. 4 Turn the off/on engine switch to the on position. To restart a warm engine, leave the choke lever in the “OPEN” position CHOKE LEVER MIN. CLOSED MAX. MIN. 4. Turn the engine switch to the “on” position 5.. -
Page 11: Electric Starting (Ng)
ELECTRIC STARTING (NG only) 2. Hot weather Use the proper oil for the temperature expected. When operating on NG, you will have to always use Use only summer blended gasoline. Using the electric start to get the unit running. Because of gasoline left over from winter may cause the the engine vacuum need to activate the fuel system unit to vapor lock. -
Page 12: Operating Speed
OPERATING SPEED Lower voltage may damage both the generator and any load connected to it. Running the engine at ex- The engine-generator must be run at the correct cessively high speeds results in high voltage, which speed in order to produce the proper electrical volt- may signifi... -
Page 13: Wiring
Emergency Transfer/Service the generator receptacles. Before plugging in all (ET/S) system available through your WINCO dealer. The emergency distribution panel must be installed the tools and cord sets, recheck the rating of the by a licensed electrician according to all applicable generator set. -
Page 14: Engine Care
ENGINE CARE NOTE: This engine requires 38 to 39 ounces of oil if it is completely drained. Use caution when refi lling the engine as some residual oil may have remained MAINTENANCE SCHEDULE in the engine. Always use the dipstick when fi lling the REGULAR SERVICE PERIOD (3) Each First... -
Page 15: Generator Care
a. Bearing - The bearing used in these generators is a heavy duty double sealed ball bearing. STANDARD DUAL-FILTER- They require no maintenance or lubrication. ELEMENT TYPE b. Receptacles - Quality receptacles have been WING NUT utilized. If a receptacle should become cracked or otherwise damaged, replace it. -
Page 16: Troubleshooting
TROUBLESHOOTING SPECIFICATIONS SPECIFICATIONS PROBLEM (SYMPTOMS) POSSIBLE HPS6000HE/I CAUSES Generator manufacturer MECC ALTE Model # S16W-130/A ——————————————————————— Part number 16346-006 Won’t Start *Low Oil Level. Rotor resistance 3.95 Ohms *Fouled spark plug. Stator resistance G1-N 0.36 Ohms *Out of fuel. Stator resistance G3-N 0.36 Ohms... -
Page 17: Control Panel Wiring Diagram
3180-10 60706-238... -
Page 18: Warranty Information
To the extent permitted by law, any and all warranties, including those of merchantability and fi tness for a particular purpose, are limited to 24 months from date of purchase. In no event is WINCO liable for incidental or consequential damages. - Page 19 WINCO cannot deny warranty solely for lack of receipts. As the generator owner, you should be aware that WINCO may deny you warranty coverage if your genera- tor or a part has failed due to abuse, neglect, or improper maintenance or unapproved modifi cations.
- Page 20 WINCO INC. 225 S. CORDOVA AVE. LE CENTER, MN 56057 507-357-6821 SERVICE DEPT. 507-357-6831 www.wincogen.com 3180-10 60706-238...
Need help?
Do you have a question about the HPS6000HE/I and is the answer not in the manual?
Questions and answers