Winco HPS6000HE/I Installation And Operator's Manual
Hide thumbs
Also See for HPS6000HE/I:
- Installation and operator's manual (20 pages) ,
- Installation & operator's manual (20 pages) ,
- Installation instructions (4 pages)
Related Manuals for Winco HPS6000HE/I
Summary of Contents for Winco HPS6000HE/I
- Page 1 HPS6000HE/I GENERATOR INSTALLATION AND OPERATORS MANUAL WINCO INC. 225 S. CORDOVA AVE. LE CENTER, MN 56057 507-357-6821 SERVICE DEPT. 507-357-6831 www.wincogen.com...
-
Page 2: Table Of Contents
COPY YOUR MODEL AND SERIAL NUMBER HERE the generator. No other WINCO generator has the same serial number as yours. If you should ever need to contact us on this unit, it will help us to USING THIS MANUAL respond to your needs faster. -
Page 3: Specifications
SPECIFICATIONS GENERATOR Model HPS6000HE/I Surge Watts 6,000 Continuous Watts 5,500 Volts 120/240 Amps 45.8/22.9 Generator Manufacturer Mecc Alte Spa Generator Model Number S16W-130/A Part Number 16346-006 Rotor Resistance 3.95 Ohms Stator Resistance 0.36 Ohms Cap Winding Resistance 2.45 Ohms Capacitors... -
Page 4: Safety Information
SAFETY INFORMATION 3. DEADLY EXHAUST GAS - This engine generator set has been designed and manufactured to Exhaust fumes from any gasoline engine contain carbon monoxide, an allow safe, reliable performance. Poor maintenance, improper or invisible, odorless and deadly gas that must be mixed with fresh air. careless use can result in potentially deadly hazards;... -
Page 5: Testing Policy
Before any generator is shipped from the factory, it is fully checked for performance. The generator is loaded to its full capacity, and the HPS6000HE/I: 120 Volt and 240 Volt receptacles are provided for voltage, current, and frequency are carefully checked. -
Page 6: Preparing The Unit
SAE 10W-30 or 5W-30 is recommended for general use. Use a full let WINCO take care of the freight claim. If you sign for the unit, the synthetic 5W-30 for starting/operating temperatures between 5°F transfer of the ownership requires that you file the freight claim ( 15°C) and... -
Page 7: Installing The Fuel Line
This optional 12 Volt DC valve is available 3. Remov Reference numbers 2 and 3 in the previous diagram are system parts through your local WINCO dealer and can be used to shut off during regulat Natural Gas supplied by the customer. -
Page 8: Changing Fuel Types
BATTERY INSTALLATION Remember that whichever fuel delivery system or type of vapor fuel used, the fuel pressure at the demand regulator installed on the engine generator must be between 4 and 6 oz (7-11 inches of water column). Any lower pressure and the unit will starve for fuel under load. Any higher and the unit will ‘flood’... -
Page 9: Oil Alert System
OIL ALERT SYSTEM INITIAL START UP This generator is equipped with a low oil shutdown system. The The throttle control on these generators is preset and locked to operate HONDA engine uses a float switch mounted inside the engine. If the at 3600 RPM (nominal) with no load speed set at 3690 RPM. -
Page 10: Natural Gas
6. When the engine starts, release the engine switch, allowing it to 5. Pull the starter grip lightly until resistance is felt, then pull return to the ‘ON’ position. briskly. 7. Gradually move choke to the open position as the engine 6. -
Page 11: Starting Hints
STARTING HINTS is loaded to its full capacity than when running no load. The slight variation in speed also affects the frequency of the output current. This frequency variation has no appreciable effect in the operation of COLD WEATHER motors, lights, and most appliances. However, electronic equipment and clocks will be affected if correct RPM is not maintained. -
Page 12: Connecting The Loads
CONNECTING THE LOADS WIRING Plug your tools such as drills, saws, blowers, sump pump, and APPLYING THE LOADS other items to be powered directly into the generator receptacles. Before plugging in all the tools and cord sets, recheck the rating of the generator set. -
Page 13: Engine Care
CHANGING THE OIL off to prevent an overload on the generator during the initial start up. See the nameplate on your generator for the amperage capabilities of your unit. Refer to the Maintenance Schedule Chart for required oil change intervals. CAUTION: EQUIPMENT DAMAGE Failure to properly limit and balance the load applied to the generator will cause the generator to produce low voltage and may damage... -
Page 14: Generator Care
CLEANING E. To loosen debris, gently tap the air filter on a hard surface. If the air filter is excessively dirty replace with a new filter. You can use pressurized air (not to exceed 30 psi) to clean the filter. Always Remove dirt and debris with a cloth or brush. -
Page 15: Control Panel Diagram
CONTROL PANEL DIAGRAM 60706-238 REV B... -
Page 16: 24 Month Limited Warranty
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE. WINCO is liable for the repair or replacement of the product only and is not liable for incidental or consequential damages as permitted by your state. This warranty gives you specific legal rights which may vary from state to state.
Need help?
Do you have a question about the HPS6000HE/I and is the answer not in the manual?
Questions and answers