Table of Contents
Advertisement
Before configuring the system, ensure all connections have been done properly.
Parameters must only be configured by qualified personnel.
System configuration with the parameters detailed in par.12.0 is done by pressing buttons "A" and "B" on the buzzer (see figure below).
Press button "A" to select the parameter to configure.
Press button "B" to select the desired setting.
11.1 - HOW TO ENTER IN PROGRAMMING MODE:
1.
Turn ignition "ON".
2.
Simultaneously press buttons "A" and "B" for approx 4 sec.
3.
Operation will be confirmed by 1 Beep and 1 Red/Green LED flash.
4.
Wait until the LED turns OFF.
11.2 - PARAMETER SETUP:
1.
Within 10 sec. after the LED turns OFF, press button "A" the number of times corresponding to the parameter to customize. At each button press there will be 1
Beep and 1 Red LED blink.
2.
Press button "B" the number of times corresponding to the desired setup. At each button press there will be 1 Beep and 1 Green LED blink.
Example: To set the maximum detection distance of the inner sensors at 80 cm => press button "A" 2 twice and then button "B" 9 times.
11.3 - SETUP CONFIRMATION:
1.
The buzzer will repeat the number of Beeps and blinks corresponding to the selected setup. After a few seconds, if the code has been successfully programmed, the
buzzer will give off a 'Jingle'. Proceed with another setup.
2.
In case of an incorrect entry, a low tone signal (Bop) will sound. Re-enter the desired code.
Engage reverse gear to transfer the new parameters from the buzzer to the control unit (data transfer timeout: 20 sec. max). A 'Jingle' will confirm data has been successfully
transfered otherwise a Bop will sound. In this case, re-engage reverse gear.
Subsequently, when shifting into reverse, the system will operate according to the configured parameters.
11.4 - RESTORE FACTORY SETTINGS
1.
Simultaneously press and hold buttons "A" and "B"; turn ignition ON.
2.
When the buzzer gives off a Beep, release buttons "A" and "B".
3.
The LED will start blinking Green/Red.
4.
When the LED stops blinking, a Jingle" will confirm the buzzer has been reset to the original factory settings.
5.
Engage reverse gear to transfer the new parameters from the buzzer to the control unit (data transfer timeout: 20 sec. max). A Beep will confirm data has been
successfully transfered otherwise a Bop will sound. In this case, re-engage reverse gear to repeat data transfer.
11.5 – HOW TO PAIR A NEW UNIT
If either unit (ECU or buzzer) is replaced, carry out pairing as follows:
1.
Make sure the Yellow wire is NOT grounded.
2.
Connect the buzzer.
3.
Turn ignition key ON.
4.
Simultaneously press buttons "A" and "B" for approx 4 sec.
5.
Operation will be confirmed by 1 Beep and 1 Green/Red LED flash.
6.
Wait for the LED to power OFF then immediately press button "A" 9 times and button "B" 9 times. Each button press will be confirmed by a Beep and 1 Red LED
blink for button "A" and 1 Green LED blink for button "B".
7.
Engage reverse gear.
8.
The buzzer will repeat the sequence of Beeps/blinks corresponding to the number of button presses.
9.
When the buzzer gives off 3 Beeps immediately ground the Yellow wire 5 times in a row, within 10 sec.
10.
A "Jingle" will confirm that the 2 units have been paired (pairing must be carried out within 30 sec.)
11.
Turn ignition key OFF, the units are now fully operational.
12.
If pairing has been unsuccessful, a Bop will sound. Repeat the pairing process.
11.0 - PARAMETER SET-UP
Designed and manufactured by GEMINI TECHNOLOGIES srl ‐ Via L. Galvani, 12 – 21020 Bodio Lomnago (VA) – Italy
Tel. +39 0332 943211 – Fax +39 0332 948080 – www.gemini‐alarm.com
ISO 9001 CERTIFIED COMPANY
Button A
LED
Button B
Rev.01 07/2018
6/9
Advertisement
Table of Contents
