Related Manuals for KROHNE OPTIPROBE
Summary of Contents for KROHNE OPTIPROBE
- Page 1 OPTIPROBE OPTIPROBE OPTIPROBE OPTIPROBE Quick Start Quick Start Quick Start Quick Start The cost efficient flow indicator © KROHNE 01/2014 - 4003344001 - QS OPTIPROBE R02 en...
-
Page 2: Table Of Contents
2.4.7 Control valve ........................... 8 2.4.8 Bends ............................8 2.4.9 Open discharge ........................9 2.4.10 Temperatures ........................9 2.5 Mounting and dismounting..................... 10 3 Electrical connections 3.1 Safety instructions......................11 3.2 Connection diagram ....................... 11 www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en... -
Page 3: Safety Instructions
If you need to return the device to the manufacturer or supplier, please fill out the form • contained on the CD-ROM and send it with the device. Unfortunately, the manufacturer cannot repair or inspect the device without the completed form. 01/2014 - 4003344001 - QS OPTIPROBE R02 en www.krohne.com... -
Page 4: Installation
Check for the correct supply voltage printed on the nameplate. 2.2 Scope of delivery The OPTIPROBE is available in two models. You receive the ordered version. 1 Model A, for fixed mounting with welded-on flange. 2 Model B, for mounting with variable insertion lengths. -
Page 5: Nameplate
Look at the device nameplate to ensure that the device is delivered according to your order. Check for the correct supply voltage printed on the nameplate. 1 Name and address of the manufacturer. 2 Type designation of the flowmeter and CE sign. 3 Calibration data. 01/2014 - 4003344001 - QS OPTIPROBE R02 en www.krohne.com... -
Page 6: Installation Conditions
5 DN ≥ 80mm. CAUTION! The OPTIPROBE is a sensor which measures flow speed at one point in the pipe. In case the flow speed has to be converted into a volume, please note that the measured value depends on the used diameter and the insertion length, because the OPTIPROBE decreases the inner surface of the pipe at the measuring section. -
Page 7: T-Section
2.4.3 T-section Figure 2-3: Distance after T-sections 1 ≥ 30 DN 2.4.4 Vibration Figure 2-4: Avoid vibrations 2.4.5 Magnetic field Figure 2-5: Avoid magnetic fields 2.4.6 Pump Figure 2-6: Installation after pump 01/2014 - 4003344001 - QS OPTIPROBE R02 en www.krohne.com... -
Page 8: Control Valve
INSTALLATION OPTIPROBE 2.4.7 Control valve Figure 2-7: Installation before control valve 2.4.8 Bends Figure 2-8: Installation in bending pipes Figure 2-9: Installation in bending pipes www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en... -
Page 9: Open Discharge
Figure 2-10: Installation before an open discharge 2.4.10 Temperatures 1 Process temperature 2 Ambient temperature CAUTION! Protect the device from direct sunlight. Temperature range [ºC] [ºF] min. max. min. max. Process temperature Ambient temperature 01/2014 - 4003344001 - QS OPTIPROBE R02 en www.krohne.com... -
Page 10: Mounting And Dismounting
4. Tighten the bolts 2 in picture above. Be sure the safety chain is attached and the bolts are tighted ! 5 Carefully open the valve. 6. Slide in the OPTIPROBE into the desired position. This might require force, depending on the pressure in the installation. 7. Tighten bolt 1 in picture above. -
Page 11: Electrical Connections
1 Electrical terminal compartment in housing of the signal converter for signal and field current cable. 2 Signal cable 3 Field current cable C 4 Connection box for measuring sensor 5 Functional ground FE 01/2014 - 4003344001 - QS OPTIPROBE R02 en www.krohne.com... - Page 12 Measuring systems for the marine industry Head Office KROHNE Messtechnik GmbH Ludwig-Krohne-Straße 5 47058 Duisburg (Germany) Tel.:+49 203 301 0 Fax:+49 203 301 103 89 info@krohne.com The current list of all KROHNE contacts and addresses can be found at: www.krohne.com...
Need help?
Do you have a question about the OPTIPROBE and is the answer not in the manual?
Questions and answers