Aeotec Door / Window Sensor 7 User Manual
  1. Manuals
  2. Brands
  3. Aeotec Manuals
  4. Accessories
  5. Door / Window Sensor 7
  6. User manual

Aeotec Door / Window Sensor 7 User Manual

Hide thumbs Also See for Door / Window Sensor 7:
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents

18/06/2021
Door / Window Sensor 7 Basic user guide (ZWA011/ZWA041)
Modified on: Thu, 3 Jun, 2021 at 2:02 PM
Aeotec Door / Window Sensor 7.
Aeotec Door / Window Sensor 7 was developed to record the condition of doors or windows with
(http://aeotec.com/z-wave-plus)
technology and S2 framework. You can find out more about
gen7.html)
wave-door-window-sensor)
To see whether Door / Window Sensor 7 Basic is known to be compatible with your Z-Wave system or not, please
reference our
Z-Wave gateway comparison
Door / Window Sensor 7
Basic can be viewed at that link.
specifications-)
Familiarize yourself with your Door / Window Sensor 7.
Package contents:
Sensor Unit.
Cover
Big Magnet.
Small Magnet.
Double-Sided Tape large (×2).
Double-Sided Tape small (x2).
Screws (×4).
Dowels( x4).
https://help.aeotec.com/support/solutions/articles/6000230382-door-window-sensor-7-basic-user-guide-zwa011-zwa041-
Aeotec Door Window Sensor 7 Basic guide : Aeotec Help Desk
. It is powered by Aeotec's Gen7
Basic by following that link.
(http://aeotec.com/z-wave-gateways)
(https://aeotec.freshdesk.com/a/solutions/articles/6000218908-door-window-sensor-7-technical-
(https://aeotec.com/z-wave-home-automation/z-wave-
Door / Window Sensor 7
listing. The
Z-Wave Plus
(https://aeotec.com/z-
technical specifications of
1/9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Door / Window Sensor 7 and is the answer not in the manual?

Questions and answers

Related Manuals for Aeotec Door / Window Sensor 7

Summary of Contents for Aeotec Door / Window Sensor 7

  • Page 1 Door / Window Sensor 7 gen7.html) (https://aeotec.com/z- Basic by following that link. wave-door-window-sensor) To see whether Door / Window Sensor 7 Basic is known to be compatible with your Z-Wave system or not, please reference our Z-Wave gateway comparison listing. The technical specifications of (http://aeotec.com/z-wave-gateways)
  • Page 2 Do not use rechargeable batteries. Ensure correct polarity when inserting the batteries. Improper battery use may damage the product. Door / Window Sensor 7 is intended for indoor use in dry locations only. Do not use in damp, moist, and/or wet locations. It contains small parts; keep away from children.

  • Page 3: Quick Start

    18/06/2021 Aeotec Door Window Sensor 7 Basic guide : Aeotec Help Desk Quick Start Pre-Installation of Door / Window Sensor 7 Basic. Open the cover by pressing the clip on the side and pulling the cover upwards. Insert a fresh 1 * 1/2 AA battery, but pay attention to the polarity Install your Door / Window Sensor 7.
  • Page 4 18/06/2021 Aeotec Door Window Sensor 7 Basic guide : Aeotec Help Desk Installation of the flat magnet When installing the flat magnet in a hidden location, make sure that it is on the longer side as seen from the mark on the Door / Windows Sensor 7 Basic.
  • Page 5 Aeotec Door Window Sensor 7 Basic guide : Aeotec Help Desk Triple-click the tamper switch on Door / Window Sensor 7 - this begins to blink five times After completion of the inclusion, it lights up once before it goes out.
  • Page 6 Set your Z-Wave controller into unpair mode. Triple-click the tamper switch on Door / Window Sensor 7 within 1.5 seconds - this will cause the LED to blink five times. After a successful exclusion, it will light up its LED for 2 seconds then deactivate.

  • Page 7: Association Groups

    Sends alarm messages when tamper is tripped Parameter Configurations. Parameter 3: Door/Window State. This parameter allows setting Door / Window Sensor 7 state when the magnet is close to the sensor. Size: 1 Byte, Default Value: 0 Setting Description closed when the magnet is near opened when the magnet is near Parameter 4: Visual LED Indications.
  • Page 8 18/06/2021 Aeotec Door Window Sensor 7 Basic guide : Aeotec Help Desk This parameter defines events that result in sending On/Off commands to devices added to the 2nd Association Group. These commands are sent alternately to switch the devices On and Off. Commands represent the values of BASIC SET command frames.
  • Page 9 18/06/2021 Aeotec Door Window Sensor 7 Basic guide : Aeotec Help Desk Time in seconds 32400 Parameter 12: Delay of tamper alarm cancellation. The time period after which a tamper alarm will be canceled. Size: 2 Byte, Default Value: 0...

This manual is also suitable for:

Zwa011Zwa041

Table of Contents