Table of Contents
Advertisement
Quick Links
HOLDING TANK MONITOR
SENDER MANUAL
710-JS | 710-ES | 710-SS
CANADA
USA
Garnet Instruments
Garnet US Inc.
286 Kaska Road
5360 Old Granbury Road
Sherwood Park, AB T8A 4G7
Granbury, TX 76049
SeeLeveL Sender Installation Manual 710-JS / 710-ES / 710-SS
INTRODUCTION
The SeeLeveL Senders 710-JS, 710-ES, 710-SS are used with SeeLeveL II
Tank Monitoring systems that can monitor either two, three or four tanks.
The 710-JS sender is 6" high (not including tabs) and has a resolution of
1/4". This model can measure tanks from 5" to 7.5" high tanks and cannot
be stacked. The higher resolution is optimal for low-profile tanks.
The 710-ES sender is 12" high (not including tabs) with a resolution of 3/8"
and can measure tanks from 5.5" to 14" high with a single sender, and up
to 26" with double-stacked senders.
The 710-SS sender is 16" high (not including tabs) and has a resolution
of 1/2". This model can measure tanks from 7" to 18" high with a single
sender, and up to 34.5" with double-stacked senders.
The senders are mounted on the outside of the holding tanks and can
be stacked to fit taller tanks. They work on most plastic or polyethylene
holding tanks that contain water-soluble fluids. They are not compatible
with metal holding tanks.
See more information about sender lengths on page 3.
The communication protocol used between our senders and displays is
proprietary allowing us to control the accuracy and functionality of our
systems ensuring our customers experience reliable operation.
SAFETY SYMBOLS INFORMATION
W
NOTE: expands on information for any procedures.
W
CAUTION: explains safety information that could cause
damage to the product, including data loss.
W
WARNING: explains dangers that might result in
personal injury or death.
710-JS-ES-SS Manual_v1.0 - 05-Jul-2022
Page 1
Advertisement
Table of Contents
Related Manuals for Garnet SeeLevel 710-JS
Summary of Contents for Garnet SeeLevel 710-JS
- Page 1 WARNING: explains dangers that might result in personal injury or death. CANADA Garnet Instruments Garnet US Inc. 710-JS-ES-SS Manual_v1.0 - 05-Jul-2022 286 Kaska Road 5360 Old Granbury Road Sherwood Park, AB T8A 4G7...
-
Page 2: Tools And Equipment Required
This manual provides information on how to install the SeeLeveL 710-JS, 710-ES, and 710-SS senders. Make sure that any metal is at least 1” away from either side, top and bottom of the sender, and at least 2”... -
Page 3: Single Configuration
DETERMINE MEASURABLE SPACE ON TANKS Find Measurable Space Single configuration Measure the height of the tank from top to bottom then determine measurable space. 1. Measure the height of the tank. • The minimum gap is 1/4", however, we recommend that the senders be installed 1/2"... - Page 4 SENDER SPECIFICATIONS 710-SS Sender 2" 710-ES Sender 2" Black ground wire Blue signal wire Continuous 710-JS Sender Segmented Segmented pads 16" pads 12" 2" Continuous Continuous Segmented pads 6" SeeLeveL Sender Installation Manual 710-JS / 710-ES / 710-SS Page 4...
- Page 5 CUTTING SENDERS PROGRAMMING THE SENDERS TABS The senders need to be cut to the required length to match the height of the measurable space of the tank. The cut must be between the sender segmented pads. Senders have a minimum length they can be cut. The minimum length for the 710-ES and 710-SS is after the first three segmented pads and the 710-JS minimum is four segmented pads.
- Page 6 PROGRAMMING THE SENDERS 710-ES AND 710-SS Senders tabs to cut for single sender or bottom sender if double-stacked. No Tabs cut NOTE: For systems that have a Galley button. Cut the GRY and the TOP tabs. The GALLEY and the GREY tanks can only have one sender, so no programming is possible for the number of senders.
- Page 7 PROGRAMMING THE SENDER 710-JS Senders tabs to cut for single senders. CAUTION: 710-JS Senders cannot be double-stacked. No Tabs cut 710-JS Sender Tabs FRESH GREY BLACK GALLEY (4-Tank systems) Examples for correcting cuts made in error. (GRY or BLK tab cut by mistake) FRESH SeeLeveL Sender Installation Manual 710-JS / 710-ES / 710-SS Page 7...
- Page 8 PREPARE SENDER FOR INSTALLATION ❶ Clean the tank ❷ Temporarily tape sender on tank CAUTION: DO NOT SKIP THE FOLLOWING STEPS. Removing the sender Clean area throughly where the sender will be mounted making sure there is no dust, grease from the tank after the sender has been permanently installed will cause damage and oil.
- Page 9 WIRING THE SENDER ❸ Connect the wiring to the pigtail PIGTAIL The following diagram shows the wiring from the sender to the display pigtail. Other wiring HARNESS connections may apply for each display model. All wiring diagrams are available on the website. TO PUMP INDICATOR +12V POWER...
-
Page 10: Signal Strength Test
SENDER TEST ❹ Verify operation before permanently sticking the sender to the tank. Tank levels operation test For the initial test, have the tank at least 1/4 full of water or sewage. Verify that the percent level reading on the display panel looks correct. - Page 11 MOUNTING THE SENDER ❻ Secure the wires ❺ Permanently adhere sender to the tank Secure the wires with duct tape, tie wraps, or Once proper operation has been confirmed, something similar so that the wires do not rattle or press against the sender, this may result in sender the sender will be ready to permanently damage or wires breaking over time.
-
Page 12: Installation Tips
INSTALLATION TIPS SeeLeveL Sender Installation Manual 710-JS / 710-ES / 710-SS Page 12...