Table of Contents
Advertisement
Quick Links
No: 31762 – 12/21 rev. 1
Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo:
LMSW-610-S, LMSW-611-S, LMSW-622-S, LMSW-641-S
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
LMSW-610-S
LMSW-611-S
Once paired to a wireless room controller or wireless bridge,
adjustment via the DLM Configuration App or LMCS-100 may
be required to meet the local energy code where installed.
The DLM Wireless Slim Switches are wireless battery powered wall
switches intended for operation with wireless room controllers or
wireless bridges in hybrid rooms.
Do not apply cleaning solvent directly onto unit. Apply cleaning solvent onto
a cloth, then wipe the unit to clean it.
NOTE: Installation shall be in accordance with all applicable
regulations, local, and NEC codes
Status/Battery
Life LED
Tap: Fade to OFF
Press & Hold: Ramp Down
LMSW-622-S
LMSW-641-S
BUTTONS AND INDICATORS
Button(s) can be set
to toggle on/off or
to function as a
scene switch
Tap when load OFF: Turn ON to last level
Tap when load ON: Go to full bright
Press & Hold: Ramp Up
Configuration Button
(Right side of Legrand badge)
Wattstopper
DLM Wireless Slim Switches with IPv6/Bluetooth(R) Low Energy Technology
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
Power Supply .......................... Battery powered, CR2032 Battery, 3VDC
Connection to DLM Network .... Wireless via LMRC-611 room controllers
.............................................................................. or LMBC-650
Wireless Radio .................................Single, Concurrent 802.15.4 and
............................................ Bluetooth Low Energy, 2.4GHz
Wireless Communication
IPv6 Mesh (6LoWPAN) Range ....................................up to 60 ft.
Bluetooth low energy Range .......................................up to 60 ft.
60 ft. max. between LMSW-6xx-S and room controller or bridge
Wireless Encryption .................................. AES-128 bit symmetric key
Environment ........................................................ For Indoor Use Only
Operating Temperature ........................32° to 140°F (0° to 60°C)
Storage Temperature ......................... 23° to 140°F (-5° to 60°C)
Relative Humidity ..............................5 to 95% (non condensing)
Compliance/Regulatory
UL, cUL, FCC, IC
RoHS
Bluetooth certified
LED Color
Red/Green/Blue
Flash
Green, 1 Blink
Blinking Green
Red, 1 Blink
Blinking Red
White
®
SPECIFICATIONS
Function
Unit Boot Up
Config Button Pressed
Push to Pair Mode
In normal operation, if any button
press, indicates low battery
Also blinks if Reset button on back is
pressed
Push n' Learn Mode
Button or Rocker pressed during
normal operation
Advertisement
Table of Contents
Related Manuals for LEGRAND Wattstopper LMSW-610-S
Summary of Contents for LEGRAND Wattstopper LMSW-610-S
- Page 1 Press & Hold: Ramp Up Press & Hold: Ramp Down Also blinks if Reset button on back is pressed Configuration Button (Right side of Legrand badge) Blinking Red Push n’ Learn Mode White Button or Rocker pressed during normal operation...
-
Page 2: Installing The Switch
Wall box mount: Wall box mounting allows for use of any standard decora-sized wall plate (not included). If using any plate other than a Legrand radiant wall plate, the top and bottom radiant mount wings should be removed from the switch. -
Page 3: Important Installation Information
WIRELESS ROOM CONNECTION LMBR-650 For networking and Distance Recommendations: managing rooms, IPv6 Mesh for 60’ max between LMSW-6xx-S and mobile device floors, and building networking of DLM (not needed for 60’ max. between LMSW-6xx-S and room rooms and devices stand-alone rooms) controller or bridge over 6LoWPAN 10’... - Page 4 1. Enter PtP mode on the room controller. Press the Config button three times (within three seconds) until the LED on the room controller flashes green. 2. Enter PtP mode on the LMSW-6xx-S. Press the Configuration button (on the right side of the Legrand badge) three times. As with the room controller, the LED on the switch will flash green.
- Page 5 1. Enter PtP mode on the LMBC-650. Using a pointed tool, press the Config button three times (within three seconds) until the LED on the LMBC-650 flashes green. 2. Enter PtP mode on the LMSW-6xx-S. Press the Config button (right side of Legrand badge) three times. As with the wireless bridge, the LED on the switch will flash green.
- Page 6 PLUG N’ GO OPERATION (PNG) Loads in fully wireless rooms will automatically bind to LMSW-6xx-S switches based on the behavior detailed for each switch below. NOTE: Wired loads in hybrid rooms will have no automatic PnG binding and must be configured with LMCS-100. However, after a switch is paired into the room, the configuration button can be pressed once to toggle loads in the room in order to verify communication and operation.
-
Page 7: Replacing The Battery
2. Locate the prying location at the bottom left corner of the switch frame (slightly below the Legrand badge), as shown. Insert a small prying tool and pull the corner of the switch frame away from the wall. The switch will detach from the mounting plate with frame and buttons intact. -
Page 8: Fcc Regulatory Statements
No. 31762 – 12/21 rev. 1 © Copyright 2021 Legrand All Rights Reserved. 800.879.8585 © Copyright 2021 Tous droits réservés Legrand. www.legrand.us/wattstopper © Copyright 2021 Legrand Todos los derechos reservados.