Allegion LEGGE 6000 Series Installation Instructions

WARNING: Accurate door preparation is essential for the functioning of this lock.
NOTE:
WARNING: WARNING: Accurate door preparation is essential for the functioning of this lock.
1 1 1 1 1
DOOR PREPARATION
NOTE: NOTE:
1 1 1 1 1 1 1 1 1 1
DOOR PREPARATION DOOR PREPARATION
Fold template at correct height (suggested height for centreline is
A Mark centre for either passage or privacy set.
B
C Mark centre of door thickness on horizontal centreline.
Fold template at correct height (suggested height for centreline is Fold template at correct height (suggested height for centreline is
A Mark centre for either passage or privacy set. A Mark centre for either passage or privacy set.
B B
C Mark centre of door thickness on horizontal centreline. C Mark centre of door thickness on horizontal centreline.
3 3 3 3 3
INS T ALL LAT C H
3 3 3 3 3 3 3 3 3 3
INS T ALL LAT C H INS T ALL LAT C H
A Insert latch into hole. Trace around face plate.
B
C Fasten latch to door so bevelled edge of latchbolt faces
jamb.
A Insert latch into hole. Trace around face plate. A Insert latch into hole. Trace around face plate.
B B
C Fasten latch to door so bevelled edge of latchbolt faces C Fasten latch to door so bevelled edge of latchbolt faces
jamb. jamb.
5 5 5 5 5
REMOVE ROSE CAPS
5 5 5 5 5 5 5 5 5 5
REMOVE ROSE CAPS REMOVE ROSE CAPS
6 6 6 6
6 6 6 6 6 6 6 6
Legge schlage Installation Instructions.indd 1
7000/9000 and Medio Series
Installation Instructions
6000/8000 and Series
Installation Instructions
Please follow the enclosed template and instructions carefully.
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully. Please follow the enclosed template and instructions carefully.
(Privacy Set Illustrated)
(Privacy Set Illustrated) (Privacy Set Illustrated)
2 2 2 2 2
DRILL HOLES
2 2 2 2 2 2 2 2 2 2
DRILL HOLES DRILL HOLES
When drilling through the door, drill from both sides to avoid
damaging the door.
A Drill a 35mm hole through the door for privacy sets and a
20mm hole for passage sets.
B Drill (2) 5mm holes through the door where through bolt
When drilling through the door, drill from both sides to avoid When drilling through the door, drill from both sides to avoid
C Drill a 24mm hole x 85mm deep into the front edge of the
damaging the door. damaging the door.
door.
A Drill a 35mm hole through the door for privacy sets and a A Drill a 35mm hole through the door for privacy sets and a
20mm hole for passage sets. 20mm hole for passage sets.
B Drill (2) 5mm holes through the door where through bolt B Drill (2) 5mm holes through the door where through bolt
C Drill a 24mm hole x 85mm deep into the front edge of the C Drill a 24mm hole x 85mm deep into the front edge of the
4 4 4 4 4
P R E P AR E J AMB & INS T ALL S T R IK E
door. door.
4 4 4 4 4 4 4 4 4 4
P R E P AR E J AMB & INS T ALL S T R IK E P R E P AR E J AMB & INS T ALL S T R IK E
(Universal Strike Illustrated)
A Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
B Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline.
(Universal Strike Illustrated)
C Use strike plate as pattern for cutout. Chisel out and
install strike.
A Mark vertical line and height centreline on jamb, exactly A Mark vertical line and height centreline on jamb, exactly
opposite centre of latch. opposite centre of latch.
B Drill (2) 20mm holes x 15mm deep, 8mm above and below B Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline. height centreline.
C Use strike plate as pattern for cutout. Chisel out and C Use strike plate as pattern for cutout. Chisel out and
install strike. install strike.
6
INSTALL FURNITURE
6 6
INSTALL FURNITURE INSTALL FURNITURE
A Insert spindles into furniture, as illustrated.
B
(When through bolt xing method is being used, cut bolts to appropriate length.)
A Insert spindles into furniture, as illustrated. A Insert spindles into furniture, as illustrated.
B B
(When through bolt xing method is being used, cut bolts to appropriate length.) (When through bolt xing method is being used, cut bolts to appropriate length.)
(Universal Strike Illustrated)
13/11/2013 9:49:40 a.m.