KaVo ARCTICA Care Instructions
  1. Manuals
  2. Brands
  3. KaVo Manuals
  4. Dental equipment
  5. ARCTICA
  6. Care instructions
KaVo ARCTICA Care Instructions

KaVo ARCTICA Care Instructions

Engine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Care instructions
KaVo ARCTICA Engine
Always be on the safe side.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ARCTICA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for KaVo ARCTICA

Summary of Contents for KaVo ARCTICA

  • Page 1 Care instructions KaVo ARCTICA Engine Always be on the safe side.
  • Page 2 Distributed by: Manufacturer: KaVo Dental GmbH Kaltenbach & Voigt GmbH Bismarckring 39 Bismarckring 39 D-88400 Biberach D-88400 Biberach Phone +49 (0) 7351 56-0 www.kavo.com Fax +49 (0) 7351 56-1488...

  • Page 3: Table Of Contents

    Care instructions KaVo ARCTICA Engine Table of contents Table of contents 1 General instructions............................4 1.1 Target group............................. 4 1.2 Symbols in these Servicing Instructions....................4 1.2.1 Hazard levels..........................4 1.2.2 General marks and symbols......................4 1.3 General note concerning servicing work " Cleaning button": ..............5 2 Servicing, daily..............................

  • Page 4: General Instructions

    Requirement Read these instructions prior to first use to avoid misuse and prevent damage. Note Please note the Instructions for Use of the ARCTICA Engine! 1.1 Target group Personnel ▶ Only employ specialist personnel that are capable of detecting risks and avoiding potential hazards by reason of their training and expertise.

  • Page 5: General Note Concerning Servicing Work " Cleaning Button

    Care instructions KaVo ARCTICA Engine 1 General instructions | 1.3 General note concerning servicing work " Cleaning button": 1.3 General note concerning servicing work " Cleaning button": During all servicing and cleaning work in the workspace, the cleaning button must be pressed and the compressed air for cleaning must be switched on.

  • Page 6: Servicing, Daily

    ▶ Wipe down the outer housing and protective door with a dry, lint-free cloth. ▶ If needed, remove soiling on the outer housing and on the outside of the protec‐ tive door with a wet cloth and warm clear water, soapy water or KaVo plastics cleaner (0.611.0030).

  • Page 7: Checking The Coolant Lubricant Filling Level

    Care instructions KaVo ARCTICA Engine 2 Servicing, daily | 2.3 Checking the coolant lubricant filling level ▶ Clean the chip tray ④ under running water or replace it if it is damaged. ▶ Insert a new chip sieve filter ③.

  • Page 8: Servicing After 80 Operating Hours

    3 Servicing after 80 operating hours | 3.1 Checking the coolant lubricant and replacing it, if needed 3 Servicing after 80 operating hours Servicing after 80 operating hours is indicated by a coloured symbol on the ARCTICA desktop and the ARCTICA display.

  • Page 9: Cleaning The Coolant Container

    Care instructions KaVo ARCTICA Engine 3 Servicing after 80 operating hours | 3.2 Cleaning the coolant container Name Mat.No. Application Mixing ratio Coolant lubricant max. marking Coolant 1 Mat. no. ZS, plastics, 0.25 l 5.5 l 1.001.6002 glass ceramics Coolant 2 Mat.

  • Page 10: Replacing The Coolant Lubricant

    Care instructions KaVo ARCTICA Engine 3 Servicing after 80 operating hours | 3.4 Replacing the coolant lubricant ▶ Re-insert the coolant container ③ in the machine. 3.4 Replacing the coolant lubricant ▶ Clean the coolant container before you replace the coolant lubricant.
  • Page 11 Care instructions KaVo ARCTICA Engine 3 Servicing after 80 operating hours | 3.4 Replacing the coolant lubricant ▶ Mix the coolant lubricant with clean tap water in measuring beaker (Mat. no. 1.009.0788). Take the mixing ratio from the table. ▶ Pull out the coolant lubricant container to the front and place it on a level surface.

  • Page 12: Cleaning The Aerosol Dust Extractor Filter And Replacing It, If Needed

    See also: 2 Also refer to IfU Arctica item 7.7 Venting the coolant lubricant pump, page 40 3.5 Cleaning the aerosol dust extractor filter and replacing it, if needed The filter of the aerosol dust extractor is located behind the cover, in the rear of the workspace.

  • Page 13: Checking And Cleaning The Clamping Surfaces Of The Tools

    Care instructions KaVo ARCTICA Engine 3 Servicing after 80 operating hours | 3.6 Checking and cleaning the clamping surfaces of the tools ▶ Clean the filter with warm water. Then press it between two pieces of cloth to dry it and re-insert the filter; replace the filter, if needed.

  • Page 14: Lubricating The Door Seals

    Care instructions KaVo ARCTICA Engine 3 Servicing after 80 operating hours | 3.8 Lubricating the door seals 3.8 Lubricating the door seals ▶ Lubricate the door seals and wiper with Vaseline. 3.9 Cleaning the chucks ▶ Clean the chucks. 3.10 Finalising the cleaning work ▶...

  • Page 15: Servicing After 160 Operating Hours

    ▶ Avoid tensioning the chuck and make sure that there is always a tool in the chuck when the machine is current-less or switched off. ▶ Use only tools that have been released by KaVo. ▶ Never insert tools into the spindle by hand.
  • Page 16 Care instructions KaVo ARCTICA Engine 4 Servicing after 160 operating hours | 4.1 Cleaning and exchanging the chuck Note If the chuck cannot be dismantled by hand, use the two tools included in the deliv‐ ery to dismantle the chuck.
  • Page 17 Care instructions KaVo ARCTICA Engine 4 Servicing after 160 operating hours | 4.1 Cleaning and exchanging the chuck Position the threaded pin in the chuck ▶ Check the position of the threaded pin in the chuck. ▶ Rotate the threaded pin back to the extent that the chuck assembly aid touches the bur stop of the chuck.

  • Page 18: Cleaning The Tool Magazine Holder

    Care instructions KaVo ARCTICA Engine 4 Servicing after 160 operating hours | 4.2 Cleaning the tool magazine holder ▶ In order to preserve the dimensional stability of the chuck assembly aid after re‐ moval from the chuck, store the chuck assembly aid in the designated package.

  • Page 19: Replacing The Coolant Lubricant And Cleaning The Coolant Tank

    Care instructions KaVo ARCTICA Engine 4 Servicing after 160 operating hours | 4.3 Replacing the coolant lubricant and cleaning the coolant tank ▶ Clean the shaft of the blank holder (spindle shaft A-axis) and the spindle shaft (motor spindle) with the brass cleaning brush.

  • Page 20: Servicing, Semi-Annual Or According To Need

    5 Servicing, semi-annual or according to need | 4.4 Finalising the cleaning work 5 Servicing, semi-annual or according to need Semi-annual servicing is indicated by a coloured symbol on the ARCTICA desktop and the ARCTICA display. ▶ Clean the filter of the electronics box and replace it, if needed.

  • Page 21: Servicing, Annual

    Care instructions KaVo ARCTICA Engine 6 Servicing, annual | 4.4 Finalising the cleaning work 6 Servicing, annual Annual servicing is indicated by a coloured symbol on the ARCTICA desktop and the ARCTICA display. Note The annual servicing of the Arctica engine may only be performed by a KaVo- trained technician.
  • Page 22 Care instructions KaVo ARCTICA Engine 6 Servicing, annual | 4.4 Finalising the cleaning work 22 / 24...

Table of Contents