iNels RFIM-20B Quick Start Manual

ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
e-mail: elko@elkoep.com
www.elkoep.com
Characteristics
• the wireless contact converter changes your existing button to a wireless one.
- four inputs enable control of four units independently.
- battery power supply (2x 3V/CR2032) with battery life of around 5 years based on frequency
of use (included in the supply).
- only impulse control
• It can be used to transmit information on switching on the contact (detector, button, technology,
logic output).
• The BOX design lets you mount it right in an installation box under the button or switch.
• When pressing the button, it sends a set signal (ON/OFF, dimming, time switching OFF/ON, blinds
up / down).
• Sending a command is indicated by a red LED.
• Option of setting light scenes, where with a single press, you can control multiple units of iNELS
RF Control.
• Range up to 200 m (in open space), if the signal is insufficient between the controller and unit, use
the signal repeater RFRP-20 or protocol component RFIO
• Communication frequency with protocol iNELS RF Control.
Radio frequency signal penetration through various construction
materials
RFRP-20
80 - 95 % 80 - 90 %
wooden structures
brick walls
with plaster boards
Safe handling
When handling a device unboxed it is important to avoid contact with
liquids. Never place the device on the conductive pads or objects, avoid
unnecessary contact with the components of the device.
2
that support this feature.
60 - 90 % 20- 60 %
reinforced concrete metal partitions
RFIM-20B
RFIM-40B
Wireless contact converter
Connection
switch
RF controlers can control:
• switches
RFSA-11B, RFSA-61B, RFSA-62B, RFSA-61M, RFSA-66M, RFSAI-61B, RFSC-11, RFSC-61, RFUS-11, RFUS-61,
RFJA-12B
• dimmers
RFDA-73/RGB, RFDA-11B, RFDA-71B, RFDEL-71B, RFDEL-71M, RFDSC-11, RFDSC-71, RFDAC-71B
• lighting
RF-RGB-LED-550, RF-White-LED-675
Indicators, settings
After inserting the battery, the red LED lights up continuously for 3 seconds and then for 5 seconds,
the selected controller function is indicated by fl ashing LED.
• double fl ash - standard RFIO
• rapid fl ashing - mode of compatibility with older actuators
If you do not want to change the function of the controller, you must not press any buttons during
this time
0 - 10 %
To switch between RFIO
If you need to change the operating mode of the controller, after inserting the battery, when the
common glass
LED is constantly lit. press buttons 1 and 3 simultaneously and hold until the LED starts to signal the
changed mode (double fl ash or rapid fl ash).
Then the buttons must be released. The selected function mode is stored in memory and after
replacing the battery, the controller continues to operate in the same mode.
If the controller is used in RFIO
actuators switch to learn mode not only the actuator (according to the instructions for the actuator),
but also the controller in the following way: Remove the battery from the remote control, press
one of the buttons several times to discharge the device, and insert the battery again. When the
LED lights up, press button 1 and keep it pressed until the controller starts signaling the learning
mode with short fl ashing LEDs. Then release the button and the button now works in RFIO
mode. To end the learning mode, remove the battery, press some of the buttons several times.
and then replace the battery. Now we press any button and the controller will start again in RFIO
operating mode.
1 / 2
RFIM-20B
buttons
IN2 IN1 IN4
IN22 IN11
2 operating mode
2 mode and compatibility mode:
2 mode, then it is necessary to instruct the controller and link to the
EN
Made in Czech Republic
Rev.0
RFIM-40B
IN2 GND
IN3 IN1 GND
2 learning
2