Wilo MTS 40 Series Installation And Operating Instructions Manual
Submersible grinder pump
Hide thumbs
Also See for MTS 40 Series:
- Installation and operating instructions manual (10 pages) ,
- Installation and operating instructions manual (108 pages) ,
- Installation and operating instructions manual (33 pages)
Subscribe to Our Youtube Channel
Related Manuals for Wilo MTS 40 Series
Summary of Contents for Wilo MTS 40 Series
- Page 1 Submersible Grinder Pumps Wilo-Drain MTS 40/MTS 40E Installation and operating instructions...
- Page 2 Fig.1: Simplex and Duplex Package Fiberglass Basin H min (S1) H min (S2, S3) Fig.2: DN 40 (1½") Dual Guide Suspension Device H min (S1) H min (S2, S3)
- Page 3 Fig.3: Portable Base H min (S1) H min (S2, S3) Fig.4: Single Phase Wiring Diagram – 2.0 hp Start capacitor Start relay for start Switch relay capacitor Terminal Block Power connection Cable 1~230 V...
- Page 5 • failure of required maintenance and repair procedures, 2.4 Safety consciousness on the job The safety instructions included in these installation and operating instructions, the existing national regu- lations for accident prevention together with any inter- Installation and operating instructions Wilo-Drain MTS 40.../MTS 40E...
-
Page 6: Product Information
The operating safety of the supplied product is only guaranteed for conventional use in accordance with Section 4 of the operating instructions. The limit values must on no account fall under or exceed those specified in the catalog/data sheet. WILO SE 04/2012... - Page 7 Thermal winding contact (NC contact), =250 V AC, =1 A, Max. contact load =30 V DC, =30 mA DC Explosion protection according to FM MTS 40E…FM Sealing Seal on the fluid side Mechanical seal Installation and operating instructions Wilo-Drain MTS 40.../MTS 40E...
-
Page 8: Description And Function
DN 40 flange connection. WILO SE 04/2012... - Page 9 • Align the inlet and pressure outlet connection to the • Once the fiberglass sump is installed, always close it pipes prepared on site. with a WILO sump cover that is suitable for the • Check the alignment and position of the fiberglass application.
- Page 10 Fitting the sump cover • The current type and voltage of the Power connection Only use suitable Wilo sump covers, because only must correspond to those stated on the name plate. these are designed for the fiberglass sump and ensure •...
- Page 11 • To do this, suspend the pump safely in a hoist. Pump with single phase motor • Switch the pump on briefly. The pump recoils in the oppo- site direction (arrow on the housing) to the motor's direction of rotation. Installation and operating instructions Wilo-Drain MTS 40.../MTS 40E...
-
Page 12: Maintenance
It is recommended to have the pump serviced and in the sump. checked by WILO Customer Service every six months. Carry out maintenance as per EN12056 Part 4. 8.2.2 “Off” switching point The “Off”... - Page 13 Clean the pump, see 6th line blocked with sludge. If the operating fault cannot be remedied, please consult a specialist technician or the nearest WILO after-sales service point or representative. 11 Spare parts Spare parts may be ordered via a local specialist retailer and/or WILOcustomer service.
- Page 14 WILO USA LLC WILO Canada Inc. W66 N1253 Forward Way Bay 7 2915 Cedarburg, WI 53012 10th Ave. N.E. Calgary, Alberta, T2A 5L4 Phone: (262) 204-6600 CANADA Phone: (866) 945-6236 (WILO CDN) FAX: (403) 277-9456...
Need help?
Do you have a question about the MTS 40 Series and is the answer not in the manual?
Questions and answers