1. Manuals
  2. Brands
  3. Controls Manuals
  4. Control Panel
  5. C3-G7230-AS
  6. Product manual

Controls C3-G7230-AS Product Manual

Engine display & control panel j1939 engine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Product Manual
Engine Display & Control Panel
J1939 Engine
Part Number: C3-G7230-AS
Revision: 1.2
______________________________________________________________________________________________________________________________________
Copyright  Controls, Inc.
P.O. Box 368 • Sharon Center, OH 44274
Phone 330.239.4345 • Fax 330.239.2845 • www.controlsinc.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C3-G7230-AS and is the answer not in the manual?

Questions and answers

Related Manuals for Controls C3-G7230-AS

Summary of Contents for Controls C3-G7230-AS

  • Page 1 Product Manual Engine Display & Control Panel J1939 Engine Part Number: C3-G7230-AS Revision: 1.2 ______________________________________________________________________________________________________________________________________ Copyright  Controls, Inc. P.O. Box 368 • Sharon Center, OH 44274 Phone 330.239.4345 • Fax 330.239.2845 • www.controlsinc.com...

  • Page 2: Table Of Contents

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S TABLE OF CONTENTS PANEL OPERATION …………….…………………………………………………………………………………….…………………………….………. MANUAL OPERATION AUTO START/STOP OPERATION SLEEP MODE MODULE CONNECTORS …………………………………………………………………………………………………….………………….……….

  • Page 3: Panel Operation

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S PANEL OPERATION MANUAL OPERATION 1) Engine Start - Turn key to CRANK position 2) Engine Stop - Turn key to OFF position...

  • Page 4: Module Connectors

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S MODULE CONNECTORS Primary Connector Secondary Connector 14 Pin 23 Pin - 3 -...

  • Page 5: Primary 14 Pin Module Connector

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S PRIMARY CONNECTOR (14 Pin) Function Function Relay #2 – ECU Signal J1939 Low Relay #1...

  • Page 6: Panel Connector

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S PANEL CONNECTORS Engine Harness Connector –Deutsch 21 pin (HDP24-24-21PE) 21 Pin Engine Harness Connector...

  • Page 7: Float Connector

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S FLOAT CONNECTOR The controller has a four pin, single / dual float connector integrated to the bottom of the control panel.

  • Page 8: Engine Alarms, Codes And Messages

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S ENGINE ALARMS, CODES AND MESSAGES WARNINGS & ALARMS When parameter is outside of its limits, the control panel flashes that parameter on the display and illuminates the yellow lamp.

  • Page 9: Indication Lamps

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S INDICATION LAMPS The panel has two lamp indicators. Engine Engine Warning Fault/Shutdown Lamp Lamp...

  • Page 10: Control Panel Specific Alarms And Shut Downs

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S CONTROL PANEL SPECIFIC ALARMS AND SHUT DOWNS The panel has its own engine safety alarms and shut downs that can be enabled. These alarms and shut downs are managed by the control panel independent from the engine ECU.

  • Page 11: Control Panel Relay Outputs

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S CONTROL PANEL RELAY OUTPUTS The panel provides relay outputs defined below located in the Output Configuration menu. The relays are rated at 5 amps.
  • Page 12 CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S f. Switch Trip - Relay will be active if digital input is active. g. Engine Run - Relay will be active when engine RPM is greater than 600. Typically used to drive an auxiliary circuit such as louvers or send a signal to a monitoring station.

  • Page 13: Service/Maintenance Messages

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S SERVICE/MAINTENANCE MESSAGES Maintenance intervals and messages can be enabled. Maintenance Configuration Menu Service Interval Message On/Off...

  • Page 14: Battery Recharge Monitor

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S BATTERY RECHARGE MONITOR A battery recharge monitoring system is available to start and run the engine to keep the battery system charged.

  • Page 15: Menu System

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S MENU SYSTEM To Enter Menu System Hold the MENU button and press the ENTER button.

  • Page 16: Viewing Menus

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S MAIN MENUS Active Engine Fault Codes View/Scroll Active Fault Codes Stored Engine Fault Codes...

  • Page 17: Configuration Menus

    CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S CONFIGURATION MENUS Input Configuration Analog Throttle (Default = None) Digital Input 1 - Pre Set to Auto Start...
  • Page 18 CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S Engine Safety Configuration Sender Check Bypass Time Period Selection (Default = 0:10) Fuel Sender Selection (Default = S-W)
  • Page 19 CONTROLS, INCORPORATED C O N T R O L S Y S T E M S & S O L U T I O N S Auto Start Configuration Auto Start Time Delay Selection (Default = 0:10) Pre Heat Time Selection (Default = 0:00)
  • Page 20 Enable Gauges (Default = No) Yes to drive MODbus gauges Tachometer (Default = 0-3000 RPM) Engine Oil Temperature Deg. F (Default = 100-250F) Transmission Oil Temperature Deg. F (Default = 100-250F) Telemetry Parameters (12) Contact Controls, Inc. for details - 19 -...

Table of Contents