Summary of Contents for Ferno PacRac+ FWEPR+ IT
- Page 1 PacRac+® Instrument Table Model FWEPR+ IT / Model FWEPR+ PX1 Read this Manual and Retain for Future Reference Users’ Manual AUGUST 2021 Pub. No. 00148-AU-V4...
-
Page 2: Ferno Customer Service
Internet www.ferno.com.au ALL OTHER LOCATIONS For assistance or information, please contact your Ferno distributor. If you do not have a Ferno distributor, please contact Ferno Customer Relations: Serial Number _________________________ Ferno-Washington, Inc., 70 Weil Way Location: Rear cross tube under tray Wilmington, Ohio 45177-9371, U.S.A. -
Page 3: Table Of Contents
Attaching the PacRac+ to a cot or iN∫X ____________________ 16 Removing the PacRac+ ________________________________ 17 Using the IV Poles _____________________________________ 18 Securing Instruments on the PacRac+ ____________________ 19 Patient Transfer _______________________________________ 21 Folding and Storing the PacRac+ ________________________ 22 © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 4: Safety Information
Tips provide recommendations for easier use of the product. 1.4 Symbol Glossary The symbols defined at right are used on the PacRac+ and/or in this users’ manual. Ferno uses symbols recognized by the International Standards Organization (ISO), American National Standards Institute (ANSI) and the emergency medical services industry. -
Page 5: Safety And Instruction Labels
PacRac+. ● practice with the PacRac+ before using it with a patient. ● ● record their training information. A sample training record sheet is provided on page 26. © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 6: About The Pacrac
Relations (page 2) or your Ferno distributor. The PacRac+ is for professional use only, by a minimum of one trained Ferno reserves the right to change specifications without notice. operator. The PacRac+ is designed and tested for use during patient transport in a ground-based ambulance. -
Page 7: Components
Side Frame Top Lock (2) Secondary Catch (2, Yellow) Side Frame Release Tray Handle (2, Red) Rear Foot Release Trigger (2) Rear Foot (2) Side Frame Bottom Lock (2) Front Foot (2) © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 8: Setup
Using a 4 mm hex wrench, attach the front-foot mount to the cot main frame (Figure 4). Fully tighten the screw. Repeat Steps 1-3 on the opposite side of the cot. © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... - Page 9 PacRac+ mounts, position the footrest with the frame facing upward as shown in Figure 2, page 8. Remove Phillips Screws Using a 4 mm hex wrench, reattach the two shock-frame mounting blocks with four new M6x45 pan-head screws (provided). © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021...
-
Page 10: Attaching The Pacrac+ Mounts To An In∫X
Using a 3 mm hex wrench and two M5x40 screws, secure the rear-foot mount to the iN∫X main frame (Figure 11). Fully tighten the screws. Do Not Remove Center Screw Repeat Steps 2-4 on the opposite side of the iN∫X. © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 11: Attaching The Pacrac+ Fixing Poles To A Powerx (Uk)
(Figures 13 and 14). Once the extension poles have been fixed tight in place, the PacRac+ can be attached to the cot (Figures 15 - 17). © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 12: Attaching The Pacrac+ Mounts To A Power X1 (Us)
M8x20 SCHS screw and one M8 Nyloc nut (Figure 21). Using a 6 mm hex wrench and 13 mm spanner, fully tighten the screw and the Nyloc nut. Repeat Steps 1-4 on the opposite side of the POWER X1 (US). © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 13: Attaching The Straps
Repeat Steps 1-4 to attach the remaining three straps (Figure 23). Use additional straps as needed (not supplied). Additional straps can be purchased from Ferno (see Parts and Service, page 25). IV FLUID BAG STRAPS... -
Page 14: Using The Pacrac
Always properly secure the PacRac+ to the cot or iN∫X as ● instructed in this manual. Always properly secure objects on the PacRac+. Use the ● equipment straps provided, plus additional straps as needed, to secure the load on the PacRac+. © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 15: Unfolding The Pacrac+ For Use
(Figure 26). Rotate the side frame handle 90° to the front of the PacRac+ to engage the side frame top lock (Figure 27). Side Frame Top Lock © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 16: Attaching The Pacrac+ To A Cot Or In∫X
POWER X1 (US) - Figure 33 NOTICE Depending on the size of the patient, the PacRac+ may prevent the use of the shock frame. PacRac+ installed on Mondial Monobloc PacRac+ installed on iN∫X © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 17: Removing The Pacrac
Push the PacRac+ toward the loading end to unseat the PacRac+ from the mounting posts (approximately 3"/ 75 mm). Lift the PacRac+ off the cot or iN∫X and set it aside. Rear-Foot Release Levers © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 18: Using The Iv Poles
Press the red button at the top of the IV pole (Figure 37) and lower the IV pole. NOTICE Include the weight of IV fluid bags and/or items attached to the IV poles when calculating the load on the PacRac+. © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 19: Securing Instruments On The Pacrac
Observe the 55 lb/25 kg load limit when Equipment straps (provided). attaching items to the PacRac+. Ferno iN∫TRAXX track system using an iN∫TRAXX mount (not provided). Load Limit (Safe Working Load) Include the weight of the IV fluid bags when calculating the load. - Page 20 (Figure 41). Slide the SafeMount to a drop-in zone. Remove the SafeMount from the track. Rotate lever left to tighten. Rotate lever Slide until right to loosen. Locking Pin engages © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021...
-
Page 21: Patient Transfer
Return the PacRac+ side frame to the locked position when the transfer is complete (Figure 44). © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 22: Folding And Storing The Pacrac
Remove and store, or neatly arrange the remaining straps to prevent damage to the straps. Store the PacRac+ in a clean, dry place when not in use. Unbuckle Restraint and Wrap Legs Twist and Buckle Restraint Straps © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 23: Maintenance
6.4 Disinfecting the PacRac+ Wipe all surfaces with disinfectant. Follow the disinfectant manufacturer’s instructions for application method and contact time. Ferno recommends you inspect the PacRac+ for damage as you disinfect it. 6.5 Cleaning the PacRac+ Remove the straps and any accessories. -
Page 24: Lubricating The Pacrac
Are the restraints properly installed? ● ● Is restraint webbing in good condition with no cuts or frayed edges? Are restraint buckles free of visible damage and do they ● operate properly? © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 25: Parts And Service
Telephone 1.937.383.1052 +1.937.383.1051 Internet www.EMSAR.com 7.2 Worldwide To order Ferno parts, and for professional repairs, contact your Ferno distributor. Your distributor is the only agent authorized by Ferno to manage, service, and repair Ferno products. 7.3 Parts List Part Description Qty. -
Page 26: Training Record
TRAINING RECORD Training Method Trainer Date Printed Name Signature Read Video/ Initials Hands-On Manual Online © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... -
Page 27: Maintenance Record
MAINTENANCE RECORD Date Maintenance Performed © Ferno-Washington, Inc. / 00148-AU-V4 / AUG 2021... - Page 28 Emergency 11 Johnstone Road Brendale QLD 4500, AUSTRALIA Rescue Height Safety Rock Climbing Mortuary © Ferno Australia | 00148-V4 | AUGUST 2021...