Heavy-duty stainless steel drum agitators, heavy-duty, back-geared agitator for mixing and maintaining suspension of industrial coatings stored in 55-gallon drums, for professional use only, 100 psi 0.7 mpa, 7 bar maximum working pressure (24 pages)
Page 1
Repair/Parts SaniForce® Sanitary Sanitary Tote Tote Unloader Unloader SaniForce® SaniForce® Sanitary Tote Unloader 3A5417L (STU) (STU) (STU) For use use with with food food grade grade bulk bulk supply supply of of of medium medium to to to high high viscosity viscosity product.
Warnings Warnings Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
Page 4
Warnings WARNING SKIN INJECTION INJECTION HAZARD HAZARD SKIN SKIN INJECTION HAZARD High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation.
Page 5
Warnings WARNING EQUIPMENT MISUSE MISUSE HAZARD HAZARD EQUIPMENT EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest Technical Data Data in all equipment manuals.
Configuration Matrix Configuration Configuration Configuration Matrix Matrix Matrix Check the identification plate (ID) for the Configuration Number of your system. Use the following matrix to define the components of your system. STU A01AAA1AA1C21 A01AAA1AA1C21 A01AAA1AA1C21 Sample Configuration Configuration Number: Number: Sample Sample Configuration...
Page 7
Configuration Matrix Approvals Approvals Approvals All models are rated: and are FDA-compliant. ATEX models with piston II 2 GD pumps are rated: Ex h IIA T4 Gb X Ex h IIIB T100°C Db X ATEX models with diaphragm II 2 GD pumps are rated: Ex h IIA 82°C...160°C Gb X Ex h IIIB T135°C Db...
Troubleshooting Troubleshooting Troubleshooting Troubleshooting 1. Follow the Pressure Relief Procedure in the operation manual before servicing the equipment. 2. Check all possible problems and causes before disassembling the system. Problem Problem Problem Cause Cause Cause Solution Solution Solution Increase Ram Up air pressure. Ram plate will not rise.
Parts Plates Plates Plates Sample Configuration Number STU.A01BAB1AA0C21 Sanitary Tote Seal Seal Con- Certifica- Unloader Frame Plate Type Material trol Accessories Wash Bin tion 01 B B B Part/Kit Description Retainer Ref. Part/Kit Part/Kit Description Description Qty. Qty. Qty. Pump/Plate Plate Retainer Retainer...
Page 24
Parts Plate Plate Plate Kits Kits Kits These kits contain parts 7.1-7.10. Kit Part Part Part Bin Type Type Type Pump Pump Pump Pump/Plate Pump/Plate Codes Pump/Plate Codes Codes Plate Plate Plate Dim Dim A A A Plate Plate Dim Plate Dim B B B Mounts...
Parts Inflatable Inflatable Inflatable Seals Seals Seals In order to determine the correct seal to configuration number data to use for your order, refer to the table below for applicable system. Sample Configuration Number STU.A01BAB1AA0C21 Sanitary Tote Seal Seal Con- Certifica- Unloader Frame...
Parts Manual Control Control Manual Manual Control Sample Configuration Number STU.A01BAB1AA0C21 Sanitary Tote Seal Seal Con- Certifica- Unloader Frame Plate Type Material trol Accessories Wash Bin tion 1 1 1 Control Part Part Part Title Description Description Description Control Control Title Title Refer...
Parts Electro - - - Pneumatic Pneumatic Control Control Electro Electro Pneumatic Control Sample Configuration Number STU.A01BAB2AA0C21 Sanitary Tote Seal Seal Con- Certifica- Unloader Frame Plate Type Material trol Accessories Wash Bin tion 2 2 2 Part Description Control Part Part Title Description...
Parts Wash Bin Wash Wash Sample Configuration Number STU.A01BAB2AA0C21 Sanitary Tote Seal Seal Con- Certifica- Unloader Frame Plate Type Material trol Accessories Wash Bin tion 1 1 1 Part Description Wash Part Part Title Description Description Refer to to to manual: manual: Wash Wash...
Technical Data Technical Data Data Technical Technical Data SaniForce STU SaniForce SaniForce Metric Metric Metric Maximum working fluid See pump manual pressure Compressed air requirement 60-100 psi 0.41-0.7 MPa, 4.1-7 bar Pressure ratio See pump manual Air consumption See pump manual. Multiply by number of pumps Flow rate @ 60 cpm See pump manual.
Page 31
California Proposition 65 Fluid Temperature Temperature Range Range Fluid Fluid Temperature Range NOTICE NOTICE NOTICE Temperature limits are based on mechanical stress only. Certain chemicals will further limit the fluid temperature range. Stay within the temperature range of the most-restricted wetted component.
Page 32
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.