FNM HPE Series Installation Manual page 37

Table of
Name
contents
Three-position key
1
lock
Rpm counter
2
(Master Tool)
CANBUS universal
3
instrument
4 MODE button
5 Direction buttons
Glows plugs pilot
6
lamp
Transmission oil
7 anomaly pilot
lamp
8 Other pilot lamps
Size and dimensions of the panels are shown in the following
table:
Fastening
Panel Fastening
4 M4
Assembled 200 x 150
screws
4 M4
Separate
screws
The CANBUS Universal Tool allows to display all the engine
operating parameters.
Volts: is the operating voltage of the battery in volts.
-
Trim: is the position proportional to the trim inclination
-
angle.
The Trim location information is only available in
applications that require the adjustment of the trim,
such as the stern drive.
Oil Press: is the engine oil pressure in bar or PSI.
-
Engine Hour: is the total number of running hours of your
-
marine engine.
Fuel Level e Fuel Left: is the indication of the fuel level in
-
the tank (it requires an additional sensor).
Water Press: is the engine coolant pressure.
-
Fuel Used: is the amount of fuel used since last reset of
-
the instrument (it requires an additional sensor).
Trans Gear: shows the current gear engaged in the
-
transmission (it requires an additional sensor).
Description
It allows to start and stop the
engine.
It measures the engine crankshaft
speed rotation in RPM
(revolutions per minute).
It allows to display all the engine
operating parameters and alarms.
To change the operating mode of
the CANBUS Universal Instrument.
They allow you to scroll through
the CANBUS Universal Tool menu
It lights on during the glow plugs
preheating phase, with the key
lock in position I and engine off.
It lights up in case of problems
with the transmission lubrication.
It requires the sensor connection.
Optional
Panel Overall
Holes
Dimensions
Position
[mm]
[mm]
219 x 169
80 x 70 160 x 99
Trans Temp: indicates the current oil temperature in the
-
transmission (it requires an additional sensor).
Trans Press: indicates the current oil pressure in the
-
transmission (it requires an additional sensor).
Boost Press: shows the current engine boost pressure
-
(turbocharger boost pressure).
Throttle o Engine Load: show the percentage relative to
-
the position of the throttle.
Coolant Tmp: shows the engine coolant temperature.
-
Water Level/Temp: shows the level or the temperature of
-
water in the optional tank (e.g.. household users, requires
an additional sensor, and the speedometer tool).
Rudder Angle: shows the rudder angle (it requires an
-
additional sensor).
Speed: shows the boat speed in knots or km/h (it requires
-
an additional sensor, and the speedometer tool). Not
compatible with the Air Temp measurement).
Air temp: shows the air external temperature (it requires
-
an additional sensor, and the speedometer tool). Not
compatible with the speed measurement).
It is possible to add to the standard supply also one or more
additional tools that allow you to view the following information
with a needle:
Perforation
template
Attached to
the manual
Attached to
the manual
Master
Speedometer
Master
Speedometer
Trim
Battery
Fuel level
Engine
temperature
Oil pressure
Water level
Rudder angle
111.3
5"
(4 3/8 in)
Master
85
4"
(2 3/8 in)
85
- 4"
(2 3/8 in)
52.4
Slave 2"
(2 1/16 in)
52.4
Slave 2"
(2 1/16 in)
52.4
Slave 2"
(2 1/16 in)
52.4
Slave 2"
(2 1/16 in)
52.4
Slave 2"
(2 1/16 in)
52.4
Slave 2"
(2 1/16 in)
52.4
Slave 2"
(2 1/16 in)
For each instrument with slave connection
addition to the first, a Master-Slave connection cable
code 1.010.117.1 (l = 30cm/12in) or code
1.010.119.1 (l = 100cm/39in) is required.
FNM® Series HPE – Installation Manual – 33
4.049.086.1
Engine revs
(rpm)
4.049.082.1
Speed
4.049.084.1
(knots)
angle 4.049.079.1
voltage
4.049.078.1
(volts)
volume
4.049.076.1
(litres)
temperature
4.049.075.1
(°C)
pressure
4.049.077.1
(bar)
volume
4.049.080.1
(litres)
angle 4.049.081.1
in