Summary of Contents for iHome AUTO VAC NOVA PRO iHRV14
Page 1
A U T O V A C N O V A P R O For support content and the latest digital copy of this manual, scan the QR code above or visit iHomeclean.com Owner’s Guide Model iHRV14...
Auto Empty Base Overview AUTOVAC Indicators Auto Base Indicators 8 - 10 Setting Up The Auto Empty Base Setting Up The AUTOVAC Using the iHome Clean App Using Your AUTOVAC Using The Remote 15 - 17 Using Powermop Scrub Main Brush Maintenance...
Page 3
SAFETY Before using this product, please read the following safety instructions and follow all safety precautions. Any operation inconsistent with this instruction manual may cause damage to this product. WARNING – To reduce the risk of fire, electric shock, or injury: •...
IN THE BOX 1 : Auto Empty Base 4: Extra Dust Bag 7: Extra HEPA Filter 1 0 : Extra Side Brush 2: Powermop Scrub Attachment 5: Power Cable 8: Extra Mop Pad 11: Parking Plate 3: Autovac Nova Pro 6: Remote 9: Cleaning Tool Questions? Contact Customer Service...
PRODUCT OVERVIEW FRONT BOTTOM BACK 1 : 360 LIDAR Module 4: Infrared Sensors 7: Detection Sensors 10: Main Brush 13: Bin Release Button 2: Home Button 5: Omnidirectional Wheel 8: Right Wheel 1 1 : 2-IN-1 Dustbin/Mop Tank 14: Dust Collection Port 3: Power Button 6: Side Brush 9: Left Wheel...
AUTO EMPTY BASE OVERVIEW NOTE: One dustbag is already pre-installed in the Auto Empty Base. Dustbag may appear to be “deflated”. This is normal. The Dustbag handle must be fully lowered as shown in order for debris to enter properly. 1 : Cover 4: LED Display Panel 7: Dust Bag...
AUTOVAC INDICATORS POWER BUTTON POWER/HOME LED STATES • Hold to turn on/off. • Flashing blue light: Powering on/configuring network/upgrading firmware. • Press to start/pause cleaning. • Solid blue light: Powered on/normal working state. • Flashing yellow light: Low battery/recharging. • Flashing green light: Charging.
AUTO BASE INDICATORS DUST BAG STATUS • Light off: Functioning Normally. • Solid white light: Dust bag is full/dust duct is blocked. • Flashing red light: Dust bag is not installed/dust bag is not installed correctly. ROBOT CHARGING STATUS • Flashing green light: Charging •...
Page 10
SETTING UP YOUR AUTOVAC The following pages outline the complete setup process. For your convenience we created a step-by-step video to help guide you through setup. Please scan the QR code to access the video and other support content.
The Auto Empty Base is designed to automatically empty and charge the iHome AUTOVAC. Ensure that there is a clear space in front and both sides so that your AUTOVAC can return to Base to re-charge and empty. We strongly recommend placement on a hard service to ensure smooth parking.
Page 12
SETTING UP THE AUTO EMPTY BASE Conveniently store parts and remote control as shown. Plug the power cable into the back panel of the Auto Empty base. Wind extra cable slack around the cord management system. 1: Remote. 2: Extra HEPA Filter 3: Cleaning Tool. 4: Extra Side Brush.
Position the Nova Pro on the floor near your Auto Empty Base. To turn on Press and Hold the Power button until the indicator turns blue. You will hear a welcome tone. NOTE: Voice prompt volume can be adjusted later in the iHome Clean App or muted using the remote control. STEP 2 Press the Home button to pair Nova Pro to your Auto Empty Base.
NOTE: Connecting Nova Pro to Wi-Fi is not required but highly recommended. Using the iHome Clean app, you can follow the steps to connect your Nova Pro to Wi-Fi . The app will let you manage Nova Pro from anywhere, set cleaning schedules, view intelligent room maps, set virtual boundaries, view clean- ing history and more! The iHome Clean app provides an easy step by step guide to get your Nova Pro connected to Wi-Fi.
After the first Auto-clean cycle Nova Pro will create a virtual map of your home, viewable in the iHome Clean app. To get the most out of your Nova Pro, use the Map Manager feature in the iHome Clean app to define Areas and set Virtual Boundaries.
USING THE REMOTE Home Button (return to charge) Manual Navigation Directional Keys Start/Pause Button ( Starts an Auto Clean Cycle OR pause/resume an existing cleaning cycle) Mute Robot Audio Notifications Spot Clean Powermop Scrub Suction Power Adjustment 10 - 20 FT NOTE: 1: It is recommended to point the remote to the front of the Nova Pro for best results.
USING POWERMOP SCRUB Your Autovac comes equipped with a Powermop Scrub mopping attachment that connects to the 2-in-1 Dustbin/Water Tank. Follow the steps below to initiate wet mopping with your Autovac. Place the mop pad onto the mop attachment and secure it to the Velcro strips. Slip corners of the mop pad over the plastic tabs at the rear of the mop attachment.
Page 18
USING POWERMOP SCRUB Remove the dustbin from the iHome Nova Pro with the mop attachment still installed. Open the water fill cap on the dustbin and fill with water, then close the cap. Please ensure that the mop attachment is connected before filling water.
Page 19
USING POWERMOP SCRUB Install the dustbin with the mop attachement still installed into the Nova Pro according to the figure below. Activate Powermop Scrub mode in the app or using the remote control.
We recommend performing regular maintenance, as outlined in the following pages, to keep your iHome Autovac Nova Pro running at optimal performance. 1: Pinch the left and right tabs on the main brush cover. Lift and remove the cover.
MAINTAINING THE DUSTBIN, FILTERS AND MOP Press the dustbin release button and remove Clean the inside of the dustbin thoroughly the dustbin. with a dry cloth. Remove the primary filter and HEPA filter, Remove the mop pad to wash wipe down the surface with a dry cloth or use (machine washable).
SIDE BRUSH AND SENSOR MAINTENANCE 1: Use a Philips screwdriver to unscrew the side brush screw and remove the side brush. 2: Remove dirt and debris and reinstall using Philips screwdriver. NOTE: It is recommended to replace the side brush every 6-12 months depending on use. Questions? Contact Customer Service Web/Email: iHomeclean.com Phone: 877-370-4580...
AUTO EMPTY BASE MAINTENANCE AUTO EMPTY BASE DUST BAG The Auto Empty Base will indicate when the dust bag is full on the smart LED display panel (Dust bag indicator will be white). Discard of dust bag once full and replace dust bag with a new one. NOTE: Extend the dust bag handle to seal the debris hole.
AUTOVAC NOVA PRO TROUBLESHOOT PROBLEM SOLUTION Unable to power on Please charge before use. This is commonly caused due to low battery. Unable to start cleaning Please charge before use. This is commonly caused due to low battery. Unable to return to Auto Empty Base •...
AUTO EMPTY BASE TROUBLESHOOT INDICATOR DEFINITION SOLUTION 1. Frequent dust collection leads to fan overheating • Fan error • Overheating protection or fan malfunction. It is recommended to • The cover is not closed properly try to collect dust after 30 minutes; 2.
Need help?
Do you have a question about the AUTO VAC NOVA PRO iHRV14 and is the answer not in the manual?
Questions and answers
we have cleaned out everything and the robot is still making a loud noise
Where is the reset button on the unit to do a factory reset?