SolaX Power X1-EVC Series User Manual
  1. Manuals
  2. Brands
  3. SolaX Power Manuals
  4. Battery Charger
  5. X1-EVC Series
  6. User manual

SolaX Power X1-EVC Series User Manual

Hide thumbs Also See for X1-EVC Series:
Table of Contents

Advertisement

Quick Links

SolaX Power Network Technology (Zhejiang) Co., Ltd.
ADD.: No. 288, Shizhu Road, Tonglu Economic Development Zone,
Tonglu City, Zhejiang Province, China.
TEL.: +86 571-56260011
E-mail: info@solaxpower.com
Copyright Declaration
The copyright of this manual belongs to SolaX Power Network Technology (Zhejiang) Co., Ltd.
Any corporation or individual should not plagiarize, partially or fully copy it (including
software, etc.), and no reproduction or distribution of it in any form or by any means shall be
allowed. All rights reserved. SolaX Power Network Technology (Zhejiang) Co., Ltd. reserves the
right of final interpretation.
614.00623.04
X1/X3-EVC
Series User Manual
7.2 kW - 22 kW (Home Edition)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X1-EVC Series and is the answer not in the manual?

Questions and answers

Related Manuals for SolaX Power X1-EVC Series

Summary of Contents for SolaX Power X1-EVC Series

  • Page 1 ADD.: No. 288, Shizhu Road, Tonglu Economic Development Zone, Tonglu City, Zhejiang Province, China. The copyright of this manual belongs to SolaX Power Network Technology (Zhejiang) Co., Ltd. TEL.: +86 571-56260011 Any corporation or individual should not plagiarize, partially or fully copy it (including E-mail: info@solaxpower.com...

  • Page 2: Table Of Contents

    Contents Contents 1 Note on this Manual......... . 03 1.1 Scope of Validity .

  • Page 3: Scope Of Validity

    Contents Notes on this Manual 1 Notes on this Manual 1.1 Scope of Validity 6.3.4 Smart Boost ........... . . 32 This manual is an integral part of the X1/X3-EVC Series EV-Charger.

  • Page 4: Safety

    Safety Safety 2 Safety 2.1 Appropriate Usage 2.2 Important Safety Instructions The X1/X3-EVC Series are AC EV charger, intended to be installed in a fixed location and connected to the AC supply. DANGER! Danger to life due to output and input high voltages in this device! PV array Inverter...

  • Page 5: Explanation Of Symbols

    Introduction Safety 3 Introduction 3.1 Basic Features Authorized service personnel must use insulated tools when installing or working with this equipment. Thanks for purchasing with the SolaX X1/X3-EVC Series EV-Charger. The SolaX Do not use the EV-Charger in case the device has defects, crack, abrasion, bare X1/X3-EVC Series can be used for charging your electric vehicle in your home.

  • Page 6: Dimension

    Introduction Introduction 3.2 Dimension Plug Type (Connector Type) Ø Socket Type Ø 249 mm 155 mm 265 mm 155 mm...

  • Page 7: Product Description

    Introduction Technical Data 4 Technical Data 3.3 Product Description 4.1 General Data Model X3-EVC-11K X1-EVC-7.2K X3-EVC-22K AC Nominal Input Phases/Lines L+N+PE 3P+N+PE 3P+N+PE Voltage [V] 50/60;±5 50/60;±5 Frequency [Hz] 50/60;±5 AC Nominal Output Voltage [V] Current [A] Power [W] 7200 11000 22000 Interface...

  • Page 8: Security Protection

    Copyright Declaration the local regulations as well. The copyright of this manual belongs to SolaX Power Network Technology (Zhejiang) Co., Ltd. Any corporation or individual should not plagiarize, partially or fully copy it (including software, etc.), and no reproduction or distribution of it in any form or by any means shall be allowed.

  • Page 9: Installation Precaution

    Installation Installation 5.3 Installation Precaution 5.4 Installation Steps The EV-Charger is designed for wall-mounted installation (IP 65). Preparation Make sure the installation site meets the following conditions: ● Below tools are needed before installation. · Not exposed to sunlight directly. ·...
  • Page 10 Installation Installation STEP 2: Fix the back bracket and the cable hook (only for Plug Type) to the wall. STEP 3: Hang the EV-Charger on the wall for trial, then estimate the required length of input cable and communication cable. After that, take the EV-Charger down. - Mark the position of the holes.
  • Page 11 Installation Installation STEP 5: Unscrew the countersunk screw of the base plate of communication board STEP 7: Strip the outer sheath of the input cable for a length of 60-70 mm, ensuring with the cross screwdriver. Then pull the base plate of communication board out. all the wires can reach the terminal blocks with a little excessive length.
  • Page 12 Installation Installation STEP 9: Insert the wires into the appropriate holes of the terminal blocks, then block STEP 10: Press the spring upward and push the base plate of communication board the terminals with the s traight screwdriver in. Then screw the countersunk screw. (torque:1.5~1.8 N·m) (torque:0.8~1.5 N·m)
  • Page 13 Installation Installation STEP 11: Push the rear cover to appropriate position of the cables and screw the self For Plug Type, connect the charging connector with the EV-Charger and hang the tapping screws with the cross screwdriver. Then tighten the waterproof fastening connecting cable on the hook.

  • Page 14: Ct Connection

    Installation Installation 5.5 CT connection -Steady the CT on the public grid. -Insert the other end of the communication cable and the terminal of CT on each side of the RJ45 terminal adapter. Diagram: grid EV-Charger Notice: The arrow on the CT must point at the public grid.

  • Page 15: Run The Ev-Charger

    Installation Operation Method 6 Operation Method 5.6 Run the EV-Charger 6.1 States Ø Start EV-Charger after checking all below steps: There are six states of the X1/X3-EVC Series EV-Charger, i.e. Idle, Stop, Charge, a) Check that the device is xed well on the wall. Complete, Fault and Unavailable.

  • Page 16: Charging Modes

    Operation Method Operation Method * Card Activation 6.3 Charging Modes Short press the “MODE SELECTION” button, the charging mode will switch If the user wants to use the card-swiping pattern, the RFID cards need to be among FAST, ECO and GREEN Modes. activated at the EV-Charger.

  • Page 17: Green Mode

    Operation Method Operation Method 6.3.1 GREEN Mode In GREEN Mode the EV-Charger will maximize the use of surplus power generated from the inverter. According to the minimum start-up charging Charging Power ECO mode (6/10/16/20/25 A) power, the charging current can be divided into two levels as 3 A and 6 A. The Max.

  • Page 18: Smart Boost

    Operation Method Operation Method 6.3.4 Smart Boost 6.4 Dynamic Load Balance Before using the Smart Boost function, set the desired charging energy(kWh) The X1/X3-EVC Series EV-Charger has default dynamic load balancing and end time for the vehicle charging on the APP. The EV-Charger will function.

  • Page 19: App Setting

    7200 W Frequency 50 Hz/60 Hz Degree of protection IP65 Protection class Class Ⅰ Next Operating temperature range -30℃~ +50℃ Connection type Socket Next Registration No. : SolaX Power Network Technology (Zhejiang) Co., Ltd. www.solaxpower.com 615.00184.02 (Example for Registration No.)
  • Page 20 App Setting App Setting Step 4: Type in your home Wi-Fi SSID and password, then Setting. Local Mode *5GHz Wi-Fi is unavailable for now. Use your smart phone to connect the SolaX Wi-Fi signal (Wi _SCxxxxxxxx). Then touch Local and type in password (initially same as the Registration No.) to access the Local Mode in the Monitoring App.
  • Page 21 App Setting App Setting Ø 2. Touch the “EV Charger” icon and then touch the setting button to enter the Settings for the EV-Charger setting page. 1. Select “Site” at the bottom and then touch the “EV Charger” icon and select your EV-Charger on the list.
  • Page 22 App Setting App Setting 3. Select “Mode Settings” and a drop-down list will appear. Set the levels of 4. Select “Boost Settings” and a drop-down list will appear. Set the Start Time Green Mode (2 levels) and ECO Mode(5 levels for X1-EVC-7.2K & X3-EVC-22K, 2 and End Time for Timer Boost, the Charge(kWh) energy and End Time for Smart Levels for X3-EVC-11K) as you want.
  • Page 23 App Setting App Setting 5. Select “Main Breaker Limit” and set the value. With the dynamic load balance 6. Select “Advanced Settings” and a drop-down list will appear. function, when the power consumption approaches the preset max value, the 1) Set and save the value of “Overvoltage Limit” and “Undervoltage Limit”. EV-Charger will reduce charge power so that the main breaker current will 2) Touch “Grid Data Source”...

  • Page 24: Troubleshooting

    Troubleshooting Troubleshooting 8 Troubleshooting 8.1 Troubleshooting Faults Solution This section contains information and procedures for solving possible problems 1.Unplug the connector from the EV; with the X1/X3-EVC Series EV-Charger, and provides you with troubleshooting tips 2.If the "Fault" indicator is off, re-plug in and try charging OverCurr_Fault to identify and solve most problems that could occur with the X1/X3-EVC Series EV- EV again;...

  • Page 25: Routine Maintenance

    Troubleshooting Troubleshooting 8.2 Routine Maintenance ● If your EV-Charger's information panel is not displaying a Fault light, check the following list to make sure that the present state of the installation allows proper The EV-Charger do not need any maintenance or correction in most condition. To operation of the unit.

  • Page 26: Decommissioning

    Decommissioning Disclaimer 9 Decommissioning 10 Disclaimer 9.1 Dismantling the EV-Charger The EV-Charger series are transported, used and operated under limited condition, such as environmental, electrical etc. SolaX shall not be liable to Disconnect the EV-Charger from the inverter and the grid. provide the service, technical support or compensation under conditions Wait for 5 minutes for de-energizing.
  • Page 27 Warranty Registration Form For Customer (Compulsory) Country Name Phone Number Email Address Zip Code State Product Serial Number Date of Commissioning Installation Company Name Installer Name Electrician License No. For Installer Module ( If Any ) Module Brand Module Size(W) Number of String Number of Panel Per String Battery ( If Any )
  • Page 28 PLEASE REGISTER THE WARRANTY IMMEDIATELY AFTER INSTALLATION! GET YOUR WARRANTY CERTIFICATE FROM SOLAX! KEEP YOUR INVERTER ONLINE & WIN SOLAX POINTS! Open your Wait for the camera app camera to and point recognize your device the QR code at the QR code Notification Click the notification banner...

This manual is also suitable for:

X3-evc seriesX1-evc-7.2ksxhX1-evc-7.2kpxhX3-evc-11ksxhX3-evc-11kpxhX3-evc-22ksxh ... Show all

Table of Contents