Polaris RW-50/15 Installation Instructions Manual
Hide thumbs Also See for RW-50/15:

Advertisement

Quick Links

Thank you for purchasing the Polaris Mazda BT50 RW-50/15 in-dash unit.
Before removal and installation, be sure to thoroughly read these instructions.
Keep these instructions with your vehicle records for future reference.
This installation guide is for reference only. Polaris takes no responsibility for any damage caused to
any vehicle through incorrect installation, unsafe practices or poor workmanship.
Warranty for this product is 3 years from date of purchase, however warranty will be void if :
• The unit is tampered with, damaged or modified in anyway.
• Reverse camera cable is cut or modified in any way
• Reverse camera is subjected to over voltage
• The Navigation SD card is damaged or tampered with in any way (this includes installing foreign
mapping or software onto the SD card)
The Mazda BT50 RW-50/15 is covered for 3 years and includes:
• Defective Equipment
• Defective Cables
Not Covered under warranty:
• Abuse
• Improper installation
• Alteration to cables (this includes cutting of any cables)
• Accidents
This Polaris BT50 RW-50/15 utilises the OEM CD player, AM/FM Radio and USB input.
If you have any specification or troubleshooting enquiries in regards to these functions please refer to
your owner's manual.
If you have any questions concerning the installation, warranty or the operation of the unit,
Polaris
please contact
We hope that you enjoy the Polaris BT50 RW-50/15 in dash unit.
All manuals and user guides at all-guides.com
Mazda BT-50 RW-50/15
installation instructions
Warranty Terms
1300 555 514.
on
1

Advertisement

Table of Contents
loading

Summary of Contents for Polaris RW-50/15

  • Page 1 Mazda BT-50 RW-50/15 installation instructions This installation guide is for reference only. Polaris takes no responsibility for any damage caused to any vehicle through incorrect installation, unsafe practices or poor workmanship. Warranty for this product is 3 years from date of purchase, however warranty will be void if : •...
  • Page 2: Wiring Diagram

    > this plug connects to the Mazda BT-50 OEM plug located in the ‘TOP SECTION’ PLUG B refers to the plug located on HARNESS 1 > this plug connects into the back of RW-50/15 interface screen PLUG C refers to the plug located on HARNESS 1 >...
  • Page 3 5. GPS External Antenna + Bracket & Screws 6. Power Amplifier Box 3. Harness 1 & Harness 2 1. RW-50/15 Fascia 2. RW-50/15 8” Interface Screen 7. Instruction Manual 8. Trim Tool 9. Rear Vision Camera 4. Bluetooth External Microphone 6.
  • Page 4 All manuals and user guides at all-guides.com IMPORTANT Before installing the RW50/15 please delete your original Bluetooth pairing from the OEM screen. If this is not done - once the RW50/15 unit is installed - your phone will keep trying to pair with the original Bluetooth.
  • Page 5 All manuals and user guides at all-guides.com Step 4 - Prepare all the cabling in preparation for the head unit to be installed. A. External Bluetooth Microphone 3. Use lever to drop steering 1.Remove door rubber and the 2. Mount microphone in the wheel column down driver’s pillar trim top right hand corner of the...
  • Page 6: External Antenna

    All manuals and user guides at all-guides.com 13. Plug harness back into 14. Reinstall trim. 12. Connect PLUG A into OEM instrument cluster panel and NOTE: please make sure the bottom plug located in the TOP SECTION remount. section of the trim goes underneath &...
  • Page 7: Rear Camera

    All manuals and user guides at all-guides.com E. Rear Camera 1. Run your long strike through chassis rail from front to rear. 4. Attach the number plate camera onto 2. Tape camera cable (large 4 pin din) onto strike at the rear of the vehicle. number plate (as shown above) 3.
  • Page 8 All manuals and user guides at all-guides.com F. Wiring Diagram Harness 2 Media USB Connect to RW-50 Interface Video out 1 Video out 2 DVR video input AUX-IN video input Plug E Reverse camera Microphone Reverse camera trigger Power amplifier box Connect to the power harness of car original head unit...
  • Page 9 All manuals and user guides at all-guides.com Step 6 - Prepare the BT50 RW-50/15 fascia OEM Fascia 1. Grab the OEM fascia and remove all 9 clips and set aside. 2. Remove the 10 screws holding the button panel and air conditioning vents in place - set aside.
  • Page 10: Step 7 - Fascia Installation

    All manuals and user guides at all-guides.com Step 7 - Fascia installation 2. Plug the OEM button panel 1. Connect PLUG & into the 3. Make sure all the cables are harness into the back of the back of the RW50/15 tucked away neatly before securing OEM button panel interface screen...
  • Page 11: Steering Wheel Controls

    All manuals and user guides at all-guides.com Steering Wheel Controls Follow these steps to program in your steering wheel controls • Go to main menu • Touch setup • Once in the settings menu, touch setup again • Scroll down until you see SWC setup •...

Table of Contents