Contents Precautions before use Personal protection equipment Protection of the environment General product view Specifications Compatible batteries User guide Adjustment of the telescopic pole Precautions for use and safety Servicing and maintenance Safety instruction Warranty conditions Advice Troubleshooting Technical information...
> Power tools must not be disposed of with household refuse. > The device, accessories and packaging must be taken to a recycling centre. > Ask the approved INFACO dealer for up-to-date information on the eco- compatible elimination of waste.
Box contents Manual Rod assembly tool Comb assembly tool Vibrating head Motorized handle Comb Fixed ou telescopic pole Specifications Reference E50048 E50048T Rated power supply 48VCC Max power 350W Max Weight 3000g 3250g Length 2,30m 2,30m à 3,30m...
VPlease ask your dealer for advice on fitting the comb. Incorrect assembly can cause wear on the comb or rods Ref : E710 The use of the INFACO (E710) screwdriver when tightening is strongly recommended to avoid damaging the tightening tips.
Page 10
Installation and connection Only use INFACO brand batteries with a 48 Volt power supply. Any use with batteries other than INFACO batteries may lead to damage. The warranty on the motorized handle will be void if batteries other than those manufactured by INFACO are used.
Precautions for use and safety The machine is fitted with an electronic board with thermal circuit-breaking. As soon as the head jams because of too strong resistance, the electronic board cuts the power to the motor and the red LED lights. To restart, place the switch in the “OFF” position, then switch it back to “ON”.
Servicing and maintenance All servicing and maintenance operations must be carried out with the tool disconnected from all power sources: Adapt the servicing frequencies to your tool use. Occasional use, space out the frequency. Intensive use, increase the frequency. Visual inspection of its condition Complete machine Cleaning Inspection by the dealer...
Page 14
Lubrication Generously lubricate the vibrating head at least once every day, in the morning before star- ting to work. Position the spray nozzle towards the ball and socket. Hold the spray can upright and then press. Grease the vibrating head at least once per day (lubrication without removing any parts).
Safety instruction IMPORTANT. To reduce the risk of electric discharges, injuries and fire when using electric tools, follow the fundamental safety measures indicated below. Read and follow these instructions before using the tool, and keep the safety instructions! Outside operations related to the use of the tool, your tool and its accessories must be disconnected and stored in their relevant packaging.
The warranty cannot entitle to compensation for: The possible immobilisation of the tool during repairs. All work carried out by a person other than approved INFACO agents will cancel the tool warranty. The repair or replacement during the warranty period does not extend or renew the initial warranty.
Advice Keep your work area tidy. Clutter in work areas increases risks of accidents. Take into account the work zone. Do not expose electric tools to rain. Do not use electric tools in a damp or wet environment. Make sure the work area is properly lit. Do not use electric tools near inflammable liquids or gases.
Troubleshooting Disruptions Causes Solutions Refit the comb by following the Incorrect comb assembly procedure and contact the dealer if necessary. Re-tighten the comb by following the Incorrect comb tightening procedure. Significant abnormal Re-tighten the rods by following the Incorrect rod tightening vibrations procedure.
Page 19
To be returned to infaco To validate the warranty, REGISTER IMMEDIATELY ONLINE ON : www.infaco.com, your warranty declaration or send this form filled out IN BLOCK CAPITALS AS SOON AS THE TOOL IS PURCHASED. Name > ............Prénom > ..........
Page 20
Serial number dealer To be kept by the dealer for the customer file customer file...
Technical information or customer service INFACO S.A.S. Bois de Roziès 81140 CAHUZAC-SUR VERE France Phone: (+33) 05 63 33 91 49 - Fax: (+33) 05 63 33 95 57 Email: contact@infaco.fr Technical videos available on the website: www.infaco.com...
Page 22
Αβεβαιότητα // Incerteza 1,9 m/s • The person authorized to compile the technical file within the company INFACO is Mr. Gregory ALVAREZ. Το πρόσωπο που είναι εξουσιοδοτημένο να καταρτίσει τον τεχνικό φάκελο εντός της INFACO είναι ο κ.ALVAREZ Grégory. A pessoa autorizada a compilar o processo técnico na INFACO é o Sr. Gregory ALVAREZ.
Page 24
. i n f a c o . c o m NOT_E50048-T_FR_05_22 FR - Manuel d’utilisation - Vibreur à olives E50048 / E50048T...