contents PW3, a multi-function handle Compatible tools Precautions before use Personal protection equipment Protection of the environment General product view Specifications Compatible batteries User guide Speed adjustment Tool gap adjustment Precautions for use and safety Servicing and maintenance Safety instruction Warranty conditions Advice Troubleshooting...
> Power tools must not be disposed of with household refuse. > The device, accessories and packaging must be taken to a recycling centre. > Ask the approved INFACO dealer for up-to-date information on the eco- compatible elimination of waste.
General product view complete comb rods Box contents Manual Rod assembly tool Comb assembly tool Vibrating head Comb Pole Specifications Reference v5000p3EF v5000p3ET Rated power supply 48VDC Max power 720W Weight 1740g 2240g Length 2.5m 2.2m to 2.8m Speed 850 to 1250 rpm These specifications are given as an indication only.
Please ask your dealer for advice on fi tting the comb. Incorrect assembly can cause wear on the comb or rods. Ref: E710 The use of the INFACO (E710) screwdriver when tightening is strongly recommended to avoid damaging the tightening tips.
Page 11
Installation and connection Only use INFACO brand batteries with a 48 Volt power supply. Any use with batteries other than INFACO batteries may lead to damage. The warranty on the motorized handle will be void if batteries other than those manufactured by INFACO are used.
Page 12
> Tighten the wing nut > Connect the power cable...
Page 13
> Connect the battery > First power up & Exit from standby mode 2 short presses on the trigger ON > 2 start-up modes 1 short press on the trigger = ON 1 short press on the trigger = OFF 1 long press on the trigger = ON Release the trigger = OFF...
Speed adjustment 10 speed settings confi gurable from 1700 to 2075 rpm > When powering on > To switch to speed adjustment mode, press the trigger until the machine starts > Required speed is selected using successive short trigger presses. There are 10 available speed settings.
Precautions for use and safety The tool is fi tted with an electronic protection system. As soon as the tool jams due to excessive resistance, the electronic system stops the motor. Restart the tool: see the “User manual” section. We also advise keeping the tool’s protective packaging for possible returns to factory customer service.
Servicing and maintenance All servicing and maintenance operations must be carried out with the tool disconnected from all power sources: Adapt the servicing frequencies to your tool use. Occasional use, space out the frequency. Intensive use, increase the frequency. Visual inspection of its condition Complete machine Cleaning Inspection by the dealer...
Page 18
Lubrication Generously lubricate the vibrating head at least once every day, in the morning before start- Use NLGI grade class 2 type grease. ing to work. Position the spray nozzle towards the ball and socket. Hold the spray can upright and then press.
Safety instruction IMPORTANT. To reduce the risk of electric discharges, injuries and fire when using electric tools, follow the fundamental safety measures indicated below. Read and follow these instructions before using the tool, and keep the safety instructions! Outside operations related to the use of the tool, your tool and its accessories must be disconnected and stored in their respective packaging.
Under no circumstances can the warranty entitle to compensation for any immobilisation of the equipment during the time required for its repair. All work carried out by a person other than approved INFACO agents will cancel the tool warranty. The repair or replacement during the warranty period does not extend or renew the initial warranty.
Advice Keep your work area tidy. Clutter in work areas increases risks of accidents. Take into account the work zone. Do not expose electric tools to rain. Do not use electric tools in a damp or wet environment. Make sure the work area is properly lit. Do not use electric tools near inflammable liquids or gases.
Troubleshooting Disruptions Causes Solutions Refi t the comb by following the Incorrect comb assembly procedure and contact the dealer if necessary. Re-tighten the comb by following Incorrect comb tightening the procedure. Signifi cant abnormal Re-tighten the rods by following Incorrect rod tightening vibrations the procedure.
To be returned to infaco To validate the warranty, REGISTER IMMEDIATELY ONLINE ON : www.infaco.com, , your warranty declaration or send this form filled out IN BLOCK CAPITALS AS SOON AS THE TOOL IS PURCHASED. Surname > ............. First name > ..........
Page 24
Serial number dealer to be kept by the dealer for the INFACO customer file INFACO S.A.S. Bois de Roziès 81140 CAHUZAC-SUR VERE France...
Technical information or After-sales INFACO S.A.S. Bois de Roziès 81140 CAHUZAC-SUR VERE France Phone: (+33) 05 63 33 91 49 - Fax: (+33) 05 63 33 95 57 Email: electrocoup@infaco.fr Technical videos available on the website: www.infaco.com...
2005/88/EC (order of 22 may 2006). La personne autorisée à constituer le dossier technique au sein d’INFACO est M. ALVAREZ Grégory. The person authorised to compile the technical file within the company INFACO is Mr. Gregory ALVAREZ. POWERCOUP PW3 -...
Page 28
. i n f a c o . c o m NOT_V5000P3E_EN_09_21 EN - User guide - Olive Harvester V5000P3E...