Table of Contents
Advertisement
Quick Links
To our customers,
Old Company Name in Catalogs and Other Documents
st
On April 1
, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Renesas Electronics website:
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
http://www.renesas.com
st
April 1
, 2010
Renesas Electronics Corporation
Advertisement
Table of Contents
Related Manuals for Renesas FP-80Q
Summary of Contents for Renesas FP-80Q
- Page 1 On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
- Page 2 Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
- Page 3 SH7046 Group FP-80Q User System Interface Board HS7046ECH61H User’s Manual Renesas Microcomputer Development Environment System SuperH™ Family/SH7046 Series Rev.4.0 2004.01...
- Page 4 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.
-
Page 5: Important Information
Renesas) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface board. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice. -
Page 6: Limited Warranty
User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of Renesas’... - Page 7 This user's manual and user system interface board are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
- Page 8 • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol.
- Page 9 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 10 Preface The HS7046ECH61H is a user system interface board that connects a user system for the SH7046 FP-80Q package to the SH7046 E6000H emulator (HS7046EPH60H).
-
Page 11: Table Of Contents
Section 1 Configuration...1 Section 2 Connection Procedures ...3 Connecting User System Interface Board to User System ... 3 2.1.1 Installing IC Socket... 3 2.1.2 Installing Cable Head... 4 Fastening Cable Head ... 4 2.1.3 Connecting User System Interface Board to EV-Chip Board ... 6 Recommended Dimensions for User System Mount Pad (Footprint) ... -
Page 12: Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-80Q package. Please make sure you have all of these components when unpacking. Screws (M2.0 x 8 mm) with flat washers Socket cover... - Page 13 CAUTION Quantity Remarks With two spacers (2.6MP x 6 mm) For the FP-80Q package (to be mounted on the user system) For the FP-80Q package (for installing MCU) For fastening board (with four flat washers) For installing an FP-80Q-packaged MCU (with four flat washers) User’s manual for HS7046ECH61H (this manual)
-
Page 14: Section 2 Connection Procedures
To connect the cable head to the user system, follow the instructions below. 2.1.1 Installing IC Socket Solder the IC socket for an FP-80Q package to the user system. Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly more solder than the MCU.) -
Page 15: Installing Cable Head
Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-80Q package on the user system with pin 1 on the user system interface board, and insert the user system interface board into the IC socket on the user system, as shown in figure 2. - Page 16 Screws (M2.0 x 12 mm) with flat washers User system Figure 2 Connecting User System Interface Board to User System Board Pin 1 IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.)
-
Page 17: Connecting User System Interface Board To Ev-Chip Board
Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. - Page 18 Spacer User system Figure 3 Connecting User System Interface Board to EV-Chip Board EV-chip board Connector No. EV-Chip Board Connector No. Board Board Connector No. UCN1 UCN1 UCN2 UCN2...
-
Page 19: Recommended Dimensions For User System Mount Pad (Footprint)
Figure 4 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-80Q package (IC149-080-017-B5: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 4 are somewhat different from those of the actual chip's mount pad. -
Page 20: Dimensions For Ev-Chip Board And User System Interface Board
Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 5. 140.0 EV-chip board 100.0 19.5 31.0 33.5 16.0 User system interface board Unit: mm Spacer Tolerance: ±0.5 mm Figure 5 Dimensions for EV-Chip Board and User System Interface Board... -
Page 21: Resulting Dimensions After Connecting User System Interface Board
Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 6. Spacer ( 6.0) Figure 6 Resulting Dimensions after Connecting User System Interface Board EV-chip board IC socket (IC149-080-017-B5... -
Page 22: Section 3 Installing The Mcu To The User System
Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 23 Screws (M2.0 x 8 mm) with flat washers User system Figure 7 Installing MCU to User System Socket cover MCU (SH7046) Pin 1 IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.)
-
Page 24: Section 4 Verifying Operation
Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7046 E6000H Emulator User's Manual (HS7046EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the extended monitor and checking the bus states with the FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. - Page 25 To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board. Crystal oscillator terminals Figure 9 Installing the Clock Oscillator Enlarged view Crystal oscillator Evaluation chip board...
-
Page 26: Section 5 Notice
Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. Do not apply excessive force to the user system interface board while it is connected to the user system. The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU. - Page 27 HS7046ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2004 Renesas Technology Corp. All rights reserved. Printed in Japan.
- Page 28 SH7046 Group FP-80Q User System Interface Board HS7046ECH61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10B0040-0400H...