Table of Contents
Advertisement
Quick Links
To our customers,
Old Company Name in Catalogs and Other Documents
st
On April 1
, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Renesas Electronics website:
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
http://www.renesas.com
st
April 1
, 2010
Renesas Electronics Corporation
Advertisement
Table of Contents
Related Manuals for Renesas FP-112B
Summary of Contents for Renesas FP-112B
- Page 1 On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
- Page 2 Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
- Page 3 SH7144 Group FP-112B User System Interface Board HS7144ECH61H User’s Manual Renesas Microcomputer Development Environment System SuperH™ Family/SH7144 Series Rev.4.0 2004.01...
- Page 4 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.
-
Page 5: Important Information
Renesas) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface cable. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice. -
Page 6: Limited Warranty
User system interface cables are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of Renesas’... - Page 7 This user's manual and user system interface cable are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
- Page 8 • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol.
- Page 9 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 10 Preface The HS7144ECH61H is a user system interface board that connects a user system for the SH7144 FP-112B package to the SH7046 E6000H emulator (HS7046EPH60H).
-
Page 11: Table Of Contents
Section 1 Configuration...1 Section 2 Environmental Conditions...3 Setting Operating Voltage and Operating Frequency ... 3 Section 3 Product Specifications ...4 Drop in Vcc Level Detection Function: ... 4 Section 4 User Interface Specifications...5 User System Interface Circuit ... 5 Section 5 Connection Procedures ...7 Connecting User System Interface Board to User System ... -
Page 12: Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-112B package. Please make sure you have all of these components when unpacking. Screws (M2.0 x 8 mm) with flat washers Socket cover... - Page 13 CAUTION Quantity Remarks With two spacers (2.6MP x 6 mm) For the FP-112B package (to be mounted on the user system) For the FP-112B package (for installing MCU) For fastening board (with four flat washers) For installing an FP-112B-packaged MCU (with four flat washers) User’s manual for HS7144ECH61H (this manual)
-
Page 14: Section 2 Environmental Conditions
Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s max. -
Page 15: Section 3 Product Specifications
Product Specifications Item Specifications Target processor SH7144F Package FP-112B Function Level limitation: This function keeps the output signal from 3-V emulator system equal to or less than power supply voltage of the user system (Vcc). User-system operating Power supply voltage conditions Vcc: 3.0 to 3.6 V... -
Page 16: Section 4 User Interface Specifications
Section 4 User Interface Specifications The user system interface board incorporates a level conversion circuit supporting a low-voltage circuit. Accordingly, when connecting the user system to the emulator, pay attention to the signal delays and the number of FANINs and FANOUTs. User System Interface Circuit The user system interface circuit of the user system interface board is shown below. - Page 17 (3) AVcc and AN7 to AN0 5Vcc QS3384 AN7 to AN0 Emulator User system AVss Figure 5 User System Interface Circuit for AVcc and AN7 to AN0...
-
Page 18: Section 5 Connection Procedures
To connect the cable head to the user system, follow the instructions below. 5.1.1 Installing IC Socket Solder the IC socket for an FP-112B package to the user system. Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly more solder than the MCU.) -
Page 19: Installing Cable Head
Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-112B package on the user system with pin 1 on the user system interface board, and insert the user system interface board into the IC socket on the user system, as shown in figure 6. - Page 20 User system Figure 6 Connecting User System Interface Board to User System Screws (M2.0 x 12 mm) with flat washers Board Pin 1 IC socket (IC149-112C15333-0B YAMAICHI ELECTRONICS Co., Ltd.) manufactured by...
-
Page 21: Connecting User System Interface Board To Ev-Chip Board
Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. - Page 22 Spacer User system Figure 7 Connecting User System Interface Board to EV-Chip Board EV-chip board Connector No. EV-Chip Board Connector No. Board Board Connector No. UCN1 UCN1 UCN2 UCN2...
-
Page 23: Recommended Dimensions For User System Mount Pad (Footprint)
Figure 8 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-112B package (IC149-112C15333-0B: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 8 are somewhat different from those of the actual chip's mount pad. -
Page 24: Dimensions For Ev-Chip Board And User System Interface Board
Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 9. 140.0 EV-chip board 100.0 19.5 31.0 33.5 16.0 User system interface board Unit: mm Spacer Tolerance: ±0.5 mm Figure 9 Dimensions for EV-Chip Board and User System Interface Board... -
Page 25: Resulting Dimensions After Connecting User System Interface Board
Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 10. Spacer ( 6.0) Figure 10 Resulting Dimensions after Connecting User System Interface Board EV-chip board IC socket (IC149-112C15333-0B... -
Page 26: Section 6 Installing The Mcu To The User System
Section 6 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.098 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 27 Screws (M2.0 x 8 mm) with flat washers User system Figure 11 Installing MCU to User System Socket cover MCU (SH7144) Pin 1 IC socket (IC149-112C15333-0B manufactured by YAMAICHI ELECTRONICS Co., Ltd.)
-
Page 28: Section 7 Verifying Operation
Section 7 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7046 E6000H Emulator User's Manual (HS7046EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the extended monitor and checking the bus states with the FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. - Page 29 To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board. Crystal oscillator terminals Figure 13 Installing the Clock Oscillator Enlarged view Crystal oscillator Evaluation chip board...
-
Page 30: Section 8 Notice
Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. Do not apply excessive force to the user system interface board while it is connected to the user system. The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU. - Page 31 HS7144ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2004 Renesas Technology Corp. All rights reserved. Printed in Japan.
- Page 32 SH7144 Group FP-112B User System Interface Board HS7144ECH61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10B0038-0400H...