Related Manuals for Renesas FP-144F
Summary of Contents for Renesas FP-144F
- Page 1 SH7145 Group FP-144F User System Interface Board HS7145ECH61H User’s Manual Renesas Microcomputer Development Environment System SuperH Family/SH7144 Series Rev.4.00 2004.1.29...
- Page 2 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.
-
Page 3: Important Information
Renesas) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface cable. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice. -
Page 4: Limited Warranty
User system interface cables are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of Renesas’... - Page 5 This user's manual and user system interface cable are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
- Page 6 • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol.
- Page 7 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 8 Preface The HS7145ECH61H is a user system interface board that connects a user system for the SH7145 FP-144F package to the SH7046 E6000H emulator (HS7046EPH60H).
-
Page 9: Table Of Contents
Section 1 Configuration...1 Section 2 Environmental Conditions...3 Setting Operating Voltage and Operating Frequency ... 3 Section 3 Product Specifications ...4 Drop in Vcc Level Detection Function: ... 4 Section 4 User Interface Specifications ...5 User System Interface Circuit ... 5 Section 5 Connection Procedures ...8 Connecting User System Interface Board to User System ... -
Page 10: Section 1 Configuration
Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-144F package. Please make sure you have all of these components when unpacking. EV-chip board Screws (M2.0 x 6 mm) Screws (M2.0 x 10 mm) - Page 11 Use a NQPACK144SD socket (manufactured by Tokyo Eletech Corporation) for the FP-144F package IC socket on the user system. Table 1 HS7145ECH61H Components No. Component Board IC socket Socket cover Screws (M2.0 x 10 mm) Screws (M2.0 x 6 mm)
-
Page 12: Section 2 Environmental Conditions
Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s max. -
Page 13: Section 3 Product Specifications
Product Specifications Item Specifications Target processor SH7145F Package FP-144F Function Level limitation: This function keeps the output signal from 3-V emulator system equal to or less than power supply voltage of the user system (Vcc). User-system operating Power supply voltage conditions Vcc: 3.0 to 3.6 V... -
Page 14: Section 4 User Interface Specifications
Section 4 User Interface Specifications The user system interface board incorporates a level conversion circuit supporting a low-voltage circuit. Accordingly, when connecting the user system to the emulator, pay attention to the signal delays and the number of FANINs and FANOUTs. User System Interface Circuit The user system interface circuit of the user system interface board is shown below. - Page 15 (3) AVcc, AVss, AN7 to AN0, and AVref 5Vcc Emulator Emulator Figure 5 User System Interface Circuit for AVcc, AVss, AN7 to AN0, and AVref (4) Other digital signals QSVcc Emulator Figure 6 User System Interface Circuit for Other Digital Signals QS3384 AN7 to AN0 AVcc...
- Page 16 (5) UVcc and UVss QSVcc Emulator Figure 7 User System Interface Circuit for UVcc and UVss Note: UVcc and UVss represent Vcc and Vss on a user system. 5Vcc and QSVcc represent Vcc generated in the user system interface cable. 5Vcc Voltage detection...
-
Page 17: Section 5 Connection Procedures
To connect the cable head to the user system, follow the instructions below. 5.1.1 Installing IC Socket Solder the IC socket for an FP-144F package to the user system. Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly more solder than the MCU.) -
Page 18: Installing Cable Head
Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-144F package on the user system with pin 1 on the user system interface board, and insert the user system interface board into the IC socket on the user system, as shown in figure 8. - Page 19 Screws (M2.0 x 10 mm) Board Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) User system Figure 8 Connecting User System Interface Board to User System...
-
Page 20: Connecting User System Interface Board To Ev-Chip Board
Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. - Page 21 Spacer User system Figure 9 Connecting User System Interface Board to EV-Chip Board EV-chip board Connector No. EV-Chip Board Connector No. Board Board Connector No. UCN1 UCN1 UCN2 UCN2...
-
Page 22: Recommended Dimensions For User System Mount Pad (Footprint)
Figure 10 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-144F package (NQPACK144SD: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 10 are somewhat different from those of the actual chip's mount pad. -
Page 23: Dimensions For Ev-Chip Board And User System Interface Board
Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 11. 140.0 EV-chip board 100.0 19.5 31.0 33.5 16.0 User system interface board Unit: mm Tolerance: ±0.5 mm Spacer Figure 11 Dimensions for EV-Chip Board and User System Interface Board... -
Page 24: Resulting Dimensions After Connecting User System Interface Board
Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 12. Spacer ( 6.0) Figure 12 Resulting Dimensions after Connecting User System Interface Board EV-chip board User system IC socket... -
Page 25: Section 6 Installing The Mcu To The User System
Section 6 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 26 Screws (M2.0 x 6 mm) Socket cover MCU (SH7145) Pin 1 IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) User system Figure 13 Installing MCU to User System...
-
Page 27: Section 7 Verifying Operation
Section 7 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7046 E6000H Emulator User's Manual (HS7046EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the extended monitor and checking the bus states with the FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. - Page 28 To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board. Crystal oscillator terminals Figure 15 Installing the Clock Oscillator Enlarged view Crystal oscillator Evaluation chip board...
-
Page 29: Section 8 Notice
Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. Do not apply excessive force to the user system interface board while it is connected to the user system. The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU. - Page 30 HS7145ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2004 Renesas Technology Corp. All rights reserved. Printed in Japan.
- Page 31 SH7145 Group FP-144F User System Interface Board HS7145ECH61H User’s Manual REJ10B0037-0400H...