Page 1
On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
Page 2
Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
Page 3
SH7206 Group FP-176C User System Interface Board User’s Manual Renesas Microcomputer Development Environment System SuperHTM Family / SH7200 Series R0E572060CFK00 Rev.1.02 2006.08...
Page 5
(iii) prevention against any malfunction or mishap. 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp.
Improvement Policy: Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as Renesas) pursues a policy of continuing improvement in design, performance, and safety of the emulator product. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice.
Page 8
2. In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this emulator.
Renesas, upon inspection, shall determine to be defective in material and/or workmanship. The foregoing shall constitute the sole remedy for any breach of Renesas’ warranty. See the Renesas warranty booklet for details on the warranty period. This warranty extends only to you, the original Purchaser.
Page 10
3. This user's manual and emulator product are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
Page 11
• READ this user's manual before using this emulator product. • KEEP the user's manual handy for future reference. Do not attempt to use the emulator product until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS Either in the user's manual or on the product, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties.
Page 12
means WARNING or CAUTION. Example: CAUTION AGAINST AN ELECTRIC SHOCK means PROHIBITION. Example: DISASSEMBLY PROHIBITED means A FORCIBLE ACTION. Example: UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
Page 13
Warnings for AC Power Supply: • If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country.
Page 14
• If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. Do not use this as it is because of the danger of electric shock and/or fire.
Page 15
Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity.
Page 16
Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
Page 17
Preface The R0E572060CFK00 is a user system interface board that connects a user system for the SH7206 FP-176C package to the SH7206 E200F emulator (R0E0200F1EMU00 or R0E572060VKK00).
Section 1 Configuration...1 Section 2 Environmental Conditions...3 Section 3 Connection Procedures ...4 Connecting User System Interface Board to User System... 4 3.1.1 Installing IC Socket ... 4 3.1.2 Installing Cable Head... 5 3.1.3 Fastening Cable Head ... 5 Connecting User System Interface Board to EV-Chip Unit ... 7 Recommended Dimensions for User System Mount Pad (Footprint)...
FP-176C package. Please make sure you have all of these components when unpacking. Screws (M2.0 x 6 mm) Socket cover User system Figure 1 User System Interface Board for the SH7206 FP-176C Package Section 1 Configuration External bus trace unit EV-chip unit Screws (M2.0 x 10 mm)
Page 20
Use a NQPACK176SD socket (manufactured by Tokyo Eletech Corporation) for the FP-176C package IC socket on the user system. Table 1 R0E572060CFK00 Components No. Component Board IC socket Socket cover Screws (M2.0 x 10 mm) Screws (M2.0 x 6 mm) Guide pins Screwdriver User’s manual...
Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Temperature Humidity Vibration Ambient gases Specifications Operating: +10 to +35°C Storage: -10 to +35°C Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Operating: 2.45 m/s max.
Section 3 Connection Procedures Connecting User System Interface Board to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned.
3.1.2 Installing Cable Head Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-176C package on the user system with pin 1 on the user system interface board, and insert the user system interface board into the IC socket on the user system, as shown in figure 2.
Page 24
Screws (M2.0 x 10 mm) Board Pin 1 IC socket (NQPACK176SD manufactured by User system Tokyo Eletech Corporation) Figure 2 Connecting User System Interface Board to User System...
Connecting User System Interface Board to EV-Chip Unit Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST.
Page 26
User system Figure 3 Connecting User System Interface Board to EV-Chip Unit External bus trace unit EV-chip unit Connector No. EV-Chip Unit Board Connector No. Connector No. User I/F Connector 1 (CN3) User I/F Connector 2 (CN4) Board Pin 1 UCN1 UCN2...
Recommended Dimensions for User System Mount Pad (Footprint) Figure 4 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-176C package (NQPACK176SD: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 4 are somewhat different from those of the actual chip's mount pad.
Page 28
0.50 Pin 1 φ1.0 Location determination hole 2.00 Figure 4 Recommended Dimensions for Mount Pad 27.10 min 23.10 max 0.50 × 43 = 21.50 0.25 10.0 Dimension and tolerance Dimension Tolerance Up to 1.2 ±0.05 1.3 to 2.0 ±0.10 2.1 to 5.0 ±0.15 5.1 to 10.0 ±0.20...
Dimensions for External Bus Trace Unit, EV-Chip Unit, and User System Interface Board The dimensions for the external bus trace unit, EV-chip unit, and the user system interface board are shown in figure 5. Pin 1 Figure 5 Dimensions for External Bus Trace Unit, EV-Chip Unit, and User System 125.0 External bus trace unit 125.0...
Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figures 6, 7, and 8. External bus trace unit EV-chip unit Spacer (φ6.0) Figure 6 Resulting Dimensions after Connecting User System Interface Board (when Connecting External Bus Trace Unit, Optional Memory Unit, and EV-Chip Unit) Optional memory unit User system...
Page 31
EV-chip unit Spacer (φ6.0) Figure 7 Resulting Dimensions after Connecting User System Interface Board (when Connecting External Bus Trace Unit and EV-Chip Unit) External bus trace unit User system 24.5 24.5 IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) Pin 1 Dimension and tolerance Dimension Tolerance...
Page 32
Spacer (φ6.0) Figure 8 Resulting Dimensions after Connecting User System Interface Board (when EV-chip unit User system 24.5 24.5 Connecting EV-Chip Unit) IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) Pin 1 Dimension and tolerance Dimension Tolerance Up to 1.2 ±0.05 1.3 to 2.0 ±0.10...
Section 4 Installing the MPU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
Page 34
Screws (M2.0 x 6 mm) Socket cover MPU (SH7206) Pin 1 IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system Figure 9 Installing MPU to User System...
Section 5 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7206 E200F Emulator User's Manual (R0E0200F1EMU00E or R0E572060VKK00E). 2. Verify the user system interface cable connections by checking the pin states with the extended monitor and checking the bus states with the FILL command (emulator command).
The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MPU. This user system interface board is specifically designed for the SH7206 E200F EV-chip unit (R0E572060VKK00). Do not use this board with any other emulator.
Page 38
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Page 40
SH7206 Group FP-176C User System Interface Board User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10B0179-0102...