LEGRAND WP2 LED Quick Start Manual

WP2 LED WEATHERPROOF LED BATTENS
1 2
NO ALTERATIONS WITHOUT DESIGN OFFICE APPROVAL
A
B
1 2 3 4
NO ALTERATIONS WITHOUT DESIGN OFFICE APPROVAL
A
C
B
D
C
E
D
F
Installation
E
G
■ Disconnect mains supply before installing, servicing or maintaining the luminaire.
F
H
■ Attach the stainless steel clips to the body of the luminaire and attach the row
of clips on one side of the luminaire to the diffuser (clip must be attached to the
G
I
protruding side of the diffuser).
■ The gear tray should be detached to assist with installation by twisting the quarter
H
K
turn fasteners.
1 2
I
■ Drill out mounting holes.
■ Use the supplied screw set to ensure IP65 is maintained.
K
■ Fit the power cable through the supplied IP65 gland.
1 2 3 4
■ Make the electrical connection at the terminal block:
•
N – Neutral
•
A – Active
•
E – Earth
■ For DALI models connect the data cable to the two terminals labelled "DA".
■ For Emergency models, an additional Switched Active terminal is provided
to allow the luminaire to be switched ON and OFF in mains mode.
For non-maintained operation, do not connect the switched active terminal.
■ For Galaxy models, see the illustration for the correct orientation of the
antenna.
■ Clip and secure the lanyards to the gear tray.
■ Secure the gear tray to the base.
■ Close the diffuser and ensure diffuser clips are locked in place..
Ceiling Mount (as supplied)
For wall mount the antenna bracket should be bend 90 degrees as shown (no need to undo the antenna).
Note: Antenna illustration is for Galaxy models.
3 4 5 6 7
5 6 7 8 9
(230.0 - MOUNTING HOLES)
(670.0)
(812.0 - MOUNTING HOLES)
(1275.0)
3 4 5 6 7
5 6 7 8 9
ANTENNA POSITION FOR 2FT BATTEN
8 9 10 11 12
10 11 12 13 14
(100.4)
8 9 10 11 12
2
1
Item Item Name
DO NOT SCALE
LIFECYCLE STATE
LEGRAND AUSTRALIA PTY. LTD. ALL
RIGHTS RESERVED. THIS DRAWING
MAY NOT BE REPRODUCED OR Released
TRANSMITTED IN ANY FORM OR BY
ANY MEANS, IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION
OF LEGRAND AUSTRALIA PTY. LTD.
GENERAL TOLERANCES UNLESS SPECIFIED DESIGN
PRADEEP 27/05/2014
LINEAR
STEP SIZE
DESIGN REVIEW melvinder singh 01 Jun 15
<3
>3 - 6incl
>6 - 30incl PD REVIEW Paul Barron 02 Jun 15
>30-120incl
>120 CTO REVIEW Dennis Galvin 03 Jun 15
ANGULAR
MATERIAL COATING SCALE
THIRD ANGLE PROJECTION
0.50
SEE PARTS SEE PARTS
FILE NAME ASSY_4FT_LED_GRP_AG05041AE
10 11 12 13 14
Wall Mount
13 14 15 16
REVISIONS "A" ORIGINAL ISSUE
REV.B PAN 150601
MAJOR MOD TO GEARTRAY
A
Specifications
All models
B
15 16
REVISIONS "A" ORIGINAL ISSUE
Supply Voltage
REV.B PAN 150601
MAJOR MOD TO GEARTRAY
A
C
Power Factor
Colour Temperature
B
D
IP Rating
(100.4)
C
E
D
F
E
G
F
H
G
I
2 SUB ASSY CASING AG04781AB 1
1 SUB ASSY - GEARTRAY AF04783AE 1
Item Item Name
Dwg/Art No Qty
DO NOT SCALE
LIFECYCLE STATE
Tel 1300 369 777
Tel +61 2 8783 4333
LEGRAND AUSTRALIA PTY. LTD. ALL
RIGHTS RESERVED. THIS DRAWING
MAY NOT BE REPRODUCED OR Released Fax +61 2 8783 4470
TRANSMITTED IN ANY FORM OR BY
ANY MEANS, IN PART OR IN WHOLE www.hpmlegrand.com.au
WITHOUT THE WRITTEN PERMISSION
OF LEGRAND AUSTRALIA PTY. LTD.
H
GENERAL TOLERANCES UNLESS SPECIFIED DESIGN PAN 01/08/2013 TITLE
LINEAR 2FT LED WP BATTEN
K
STEP SIZE DESIGN REVIEW melvinder singh 01 Jun 15
<3
>3 - 6incl
>6 - 30incl PD REVIEW Paul Barron 02 Jun 15 WITH GRP V3236F CASE
>30-120incl
>120 CTO REVIEW
Dennis Galvin 03 Jun 15
ANGULAR
MATERIAL COATING SCALE SHEET CAT NO. FILE NO. REVISION
THIRD ANGLE PROJECTION
AG05041AA B.4
SEE PARTS SEE PARTS 0.50 A1 TBA
FILE NAME ASSY_2FT_LED_GRP_AG05041AD UNLESS OTHERWISE STATED ALL DIMENSIONS IN MM
SHEET 2 OF 2
13 14 15 16
I
SUB ASSY CASE AG04781AC 1
SUB ASSY - GEARTRAY AF04783AF 1
Dwg/Art No Qty
Tel 1300 369 777
Tel +61 2 8783 4333
Fax +61 2 8783 4470
www.hpmlegrand.com.au
TITLE
4FT LED WP BATTEN
K
WITH GRP V3236F CASE
SHEET CAT NO. FILE NO. REVISION
A1 TBA AG05041AE B.6
UNLESS OTHERWISE STATED ALL DIMENSIONS IN MM SHEET 2 OF 2
15 16
Ceiling Mount (as supplied)
For wall mount undo the antenna and install
as shown.
ANTENNA POSITION FOR 4FT BATTEN
230 - 240 V a.c. 50 Hz
>0.9
4000 K
IP65
Wall Mount