Honeywell Home T6 Pro Smart Professional Install Manual page 15

# ISU ISU Name ISU Options (defaults in bold)
378 EM Heat CPH 1 - 12 CPH
(Heating cycle rate
Emergency Heat)
Off, 1 - 5 minutes
387 Compressor
Protection
390 Ext Fan Run Time Off, 30, 60, 90 seconds
in Cool 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 minutes
391 Ext Fan Run Time Off, 30, 60, 90 seconds
in Heat 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 minutes
425 Adaptive Recovery On, Off
429 Max Cool Temperature from Min. Cool Temp. to 99 °F or to 37.0 °C (90 °F or 32 °C)
430 Min Cool Temperature from 50 °F or 10.0 °C to Max. Cool Temp. (50 °F or 10 °C)
431 Max Heat Temperature from Min. Heat Temp. to 90 °F or to 32.0 °C (90 °F or 32 °C)
432 Min Heat Temperature from 40 °F or 4.4 °C to Max. Heat Temp. (50 °F or 10 °C)
500 Indoor Sensor Yes, No
515 Sensor type 10k, 20k
520 Temperature Control Thermostat, Wired, Average
702 Air Filters 0 - 2
711 Air Filter 1 Reminder Off
10, 20, 30, 45, 60, 90, 120, 150 Run Time Days
30, 45, 60, 75 Days
3, 4, 5, 6, 9, 12, 15 Months
712 Air Filter 2 Reminder Off
10, 20, 30, 45, 60, 90, 120, 150 Run Time Days
30, 45, 60, 75 Days
3, 4, 5, 6, 9, 12, 15 Months
Notes
This ISU is only displayed when Emergency Heat is configured and ISU 253: Aux/E Terminal Control is set to
control Aux and E heat Independently. The recommended cycle rate settings are below for each heating equip-
ment type:
Standard Efficiency Gas Forced Air = 5 CPH; High Efficiency Gas Forced Air =
3 CPH; Oil Forced Air = 5 CPH; Electric Forced Air = 9 CPH.
The thermostat has a built in compressor protection (minimum off timer) that prevents the compressor from
restarting too early after a shutdown. The minimum-off timer is activated after the compressor turns off. If
there is a call during the minimum-off timer, the thermostat shows "Wait" in the display. This ISU is displayed if
ISU 220 is set to at least 1 stage.
After the call for cooling ends, the thermostat keeps the fan on for the selected amount of time for increased
efficiency. This may reintroduce humidity into the living space. This ISU is displayed if ISU 220 is set to at least
1 stage.
After the call for heating ends, the thermostat keeps the fan on for the selected amount of time for increased
efficiency. This ISU is displayed if ISU 230 is set to Thermostat Controls Fan.
Adaptive Intelligent Recovery (AIR) is a comfort setting. Heating or cooling equipment will turn on earlier,
ensuring the indoor temperature will match the setpoint at the scheduled time.
The user cannot set the cooling temperature above this level.
The user cannot set the cooling temperature below this level.
The user cannot set the heating temperature above this level.
The user cannot set the heating temperature below this level.
Set this ISU when you want to wire a remote indoor sensor to the "S" terminals on the UWP - see "Wiring" on
page 6. This ISU is only displayed only if ISU 130 is set to NO wired outdoor sensor configured
Choose resistance type of wired indoor sensor. This ISU is only displayed when indoor sensor is configured -
ISU 500.
This ISU is only displayed when indoor sensor is configured - ISU 500. You can choose what temperature
source to be used or you can ask thermostat to use both thermostat and remote sensors for higher accuracy of
measurement.
This ISU refers to the number of air filters in the system.
Choose either calendar or equipment run time-based reminder.
Choose either calendar or equipment run time-based reminder.