Content Tools and man force ................3 Parts List....................4-9 Product Description................10 Safety Instruction.................10-11 Mounting....................12-24 Dismounting...................25 Storage....................25 Disposal....................25 Attention: Read this instruction manual carefully and completely before mounting and usage. Keep this manual for future reference. Dear Customer, Congratulations and welcome to our Villa Pergola family. To enjoy your Villa Pergola for its lifetime and for you and other’s safety, please follow the assembly instructions.
Tools and man force Recommended: 2 or 3 people Additional tools: 1.Ladder 2. M10/13 open wrench supplied 3. Rubber mallet 4.Tape measure 5. 5mm hexagon wrench supplied 6. Pencil 7.Spirit level 8. Electric drill...
Parts List Please check all parts against the parts list before commencing construction of pergola. SIZE:10’x10’ or 300X300CM PARTS LIST Aluminum profile parts list: (A1) Beam (B1 ) Beam (C1) Beam (C2) Beam (D1) Post + post connector (D2) Post + post connector (G) Common Louver (H) Steering Louver (I) Strenthen Louver...
Page 6
Hardware and other parts: ①M8x20 countersunk screw ②50 to 40 connector ③Base plate ④Upright cover ⑤M10 screw cap ⑥M8x20 Hexagon bolt ⑦Plastic washer DAP25 ⑦Locking nut ⑨Motor with motor bracket ⑩Gutter connector ⑪ wall bracket ⑫Slider ⑬L bracket ⑭Cover plate ⑮M8X100 Internal anchor ⑯M8X100 Anchor ⑰Base plate caps...
Page 7
SIZE:10’x13’ or 300X400CM PARTS LIST Aluminum profile parts list: (A1) Beam (B1 ) Beam (C1) Beam (C2) Beam (D1) Post + post connector (D2) Post + post connector (G) Common Louver (H) Steering Louver (I) Strenthen Louver (E1) Gutter (E2) Gutter (F1) Gutter (F2) Gutter (J) Steering profile...
Page 8
Hardware and other parts: ①M8x20 countersunk screw ②50 to 40 connector ③Base plate ④Upright cover ⑤M10 screw cap ⑥M8x20 Hexagon bolt ⑦Plastic washer DAP25 ⑦Locking nut ⑨Motor with motor bracket ⑩Gutter connector ⑪ wall bracket ⑫Slider ⑬L bracket ⑭Cover plate ⑮M8X100 Internal anchor ⑯M8X100 Anchor ⑰Base plate caps...
Page 9
SIZE:13’x13’ or 400X400CM PARTS LIST Aluminum profile parts list: (A1) Beam (B1 ) Beam (C1) Beam (C2) Beam (D1) Post + post connector (D2) Post + post connector (G) Common Louver (H) Steering Louver (I) Strenthen Louver (E1) Gutter (E2) Gutter (F1) Gutter (F2) Gutter (J) Steering profile...
Page 10
Hardware and other parts: ①M8x20 countersunk screw ②50 to 40 connector ③Base plate ④Upright cover ⑤M10 screw cap ⑥M8x20 Hexagon bolt ⑦Plastic washer DAP25 ⑦Locking nut ⑨Motor with motor bracket ⑩Gutter connector ⑪ wall bracket ⑫Slider ⑬L bracket ⑭Cover plate ⑮M8X100 Internal anchor ⑯M8X100 Anchor ⑰Base plate caps...
Product Description Make the most of your outdoor living area with your pergola. Relax and enjoy the outdoors while being protected from sun. The coated aluminum frame pergola is perfect for shading your garden, deck, courtyard and swimming pool. Important Safety Instructions Warning: For the safety of you and other persons it is important to follow below instructions and obey warnings.
Page 12
Keep children and pets out of the working area during assembly and adjustments. This product and its fixing parts are only suitable for installation on a plain cement wall or stable brickwork. If the wall/brickwork shows cracks you have to consult a professional.
Mounting and usage Step 1 ○ Attach base plate③x2 to the bottom of posts (D1 /D2),use bolts 1 x 8 to attach with hex key or electric drill. D1, D2 posts should be installed diagonally as below. Please make sure all posts on the same horizontal plane.
Page 14
Step 2 ○ ○ According the height of D1 to measure the height of 11 ,use anchor to fasten...
Page 15
Step3 ○ ○ B1 . Use bolts 12 x4 to fasten beam...
Page 16
Step 4 ○ ○ ○ ○ ○ A1 / C2 into D1 ,then connect B1 with 13 ,fasten the screws. Insert the...
Page 17
Step 5 ○ Cover the post with 4 x2,fasten the screws.
Page 18
Step 6 ○ ○ ○ ○ C1 and C2 into B1 with 13 , fasten the screws. Cover the beam on Connect the ○ 14 ,fasten the screws both sides with...
Page 19
Step 7 ○ ○ ○ ○ E1 , E2 , F1 , F2 in proper position as picture Placed all gutter...
Page 20
Step 8 ○ 10 x2 gutter connector and②x2 50 to 40 connector. Fasten Connect the female and male plugs for the LED lighting, (DC24V to DC24V) and motor (DC24V to DC24V) and plug the power cable into local socket. Step 9...
Page 22
Step 10 Located holes in centre of beams(ⒶandⒷ) Place centre louver Ⓗinto 12th slot, lining up with the holes for 300x300 cm size. * Place centre louver Ⓗinto 16th slot, lining up with the holes for 300x400 cm and 400x400 cm size. Using M10 nut ⑤X2, secure the louver in place Place Driving louver Ⓘin line with 7th slot on the beam ⒶandⒷ.
Page 23
Step 13 ○ J x 2 (flat L-shaped aluminum profile). One for each other of the slats is required. Use bolt ⑥ x46, plastic spacer⑦x46 and nut⑧x46 to tighten for 300X300cm size. Use bolt ⑥ x64, plastic spacer⑦x64 and nut⑧x64 to tighten for both 300X400 cm and 400x400 cm size.
Page 24
Step 14 ○ 16 x8 on each post. Mark holes for expansion bolt Note the drill size should be 12 mm. Insert the bolts. Use a hammer drill if necessary. Place the posts over the bolts. Tighten the nuts. Once installed, make sure any remaining plastic is removed and silicone is used along all corners and gutters to waterproof.
Page 25
WARNING : Make sure louvers are open when mild to strong winds occur for safety. Motor setup...
Dismounting If you want to disassemble the Pergola, please follow the following process. Attention! At least two people are needed for this step. Keep the Pergola louvers open before you begin with dismounting. Bind the Louvers of the Pergola together to avoid unintended unfolding.