Advertisement
Quick Links
XDS510USB JTAG Emulator
About This Installation Guide
This Installation Guide is for the XDS510USB Emulator product. The XDS510USB Emulator
is a module to be attached to a PC for hardware engineers and software programmers to develop
DSP applications.
The text paragraphs in this Guide are very important for proper device functioning and for
preventing any possible damages on the XDS510USB Emulator device and project target board.
These paragraphs are shaded as in the following example. Please carefully read each of the
shaded text.
This is an example of a very important text paragraph mentioned above.
Introduction
Overview
XDS510USB Emulator is designed to use with digital signal processors (DSPS) operating at
1.0-5.0 volts. The emulator itself is a bus-powered USB device. It is fully plug and play
compatible and is fully powered by the host computer's USB connection. The XDS510USB
Emulator operates with TI Code Composer Studio IDE debug tool and is fully compatible with
windows 98/SE/ME/2000/XP/VISTA.
Features
XDS510USB Emulator has the following features:
Supports Texas Instruments DSP with a JTAG (IEEE1149.1) interface: C2000, C5000,
●
C6000 ,OMAP platforms.
Supports Texas Instruments Code Composer Studio.
●
Supports 1.0-5.0 volt DSP devices.
●
USB compatible. Simple Connection, fully Plug-and-Play compatible-no jumpers, noswitch
●
settings.
Hot pluggable
●
Power provided by USB bus , no additional power supply is required.
●
Installation Guide
IMPORTANT INFORMATION
1
Advertisement
Related Manuals for Spectrum Digital XDS510USB
Summary of Contents for Spectrum Digital XDS510USB
- Page 1 The text paragraphs in this Guide are very important for proper device functioning and for preventing any possible damages on the XDS510USB Emulator device and project target board. These paragraphs are shaded as in the following example. Please carefully read each of the shaded text.
- Page 2 Supported Operating Systems Windows98/ME/2000/XP/VISTA ● Detailed Installation What you will need The following detailed list contains all items needed to install and run with the XDS510USB JTAG Emulator. PC with a free Universal Serial Bus (USB) port ● XDS510USB JTAG Emulator ●...
- Page 3 The USB Device Drivers Installation Driver installation for windows 2000/XP: 1. After plug the XDS510USB JTAG Emulator into the host computer’s USB port, the system should display the Found New Hardware (Figure A-1) dialog box. This dialog box indicates the computer operating system has found a new USB device.
- Page 4 Figure A-2 3. Click on next and system will display the window as shown in Figure A-3. Figure A-3 4. Check on “Search for a suitable driver for my device(Recommended)” and click on next. The system will display a window as shown in Figure A-4.
- Page 5 Figure A-4 5. Check on “CD-ROM drives” and click on next. The system will prompt you to insert the manufacturer’s installation disk, as shown in the Figure A-5. Figure A-5 6. Click on Browse and locate the file usb510.Inf in the installation CD(TI DSP Emulator\XDS510 USB_driver), or in the folder where you have downloaded the file into, as shown in Figure A-6.
- Page 6 XDS510 Emulator. Insert the XDS510USB driver disk into your CD-ROM, Double click on Setup.Exe(TI DSP Emulator\XDS510 CCS_driver) to install the JTAG emulator tools for CCS. In order to run the application properly the XDS510 CCS Driver must reside in the same folder in which the Code Composer Studio IDE is installed.For example,if the Code Composer Studio IDE...
- Page 8 CCS Emulate Configuration...
- Page 9 XDS510USB JTAG Emulator has provided many typical emulate configuration. The user can use them directly without modification. 1. Launch the Setup CCStudio v3.3 , the program will display the window as shown in figure C-1. Figure C-1 2. Select xds510 emulator in the platform list;...
- Page 10 Figure C-2 Figure C-3...
-
Page 11: Important Note
1 on THE cable matches Pin 1 on the DSP target system. Connecting the cable incorrectly may cause damages on your DSP target system or the XDS510USB Jtag Emulator. The JTAG interface flat cable comes with a keyed 2x7-socket connector that should match...
Need help?
Do you have a question about the XDS510USB and is the answer not in the manual?
Questions and answers