Advertisement
Available languages
Available languages
SLEEP SAFE BED GUARD
GB
IMPORTANT: RETAIN FOR FUTURE REFERENCE - READ
CAREFULLY - YOUR CHILD'S SAFETY MAY BE AFFECTED IF
YOU DO NOT FOLLOW THESE INSTRUCTIONS CAREFULLY.
WARNING: TO AVOID DANGER OF SUFFOCATION REMOVE
PLASTIC COVER BEFORE USING THIS ARTICLE. THIS COVER
SHALL BE DESTROYED OR KEPT AWAY FROM BABIES AND
CHILDREN..
WARNINGS
WARNING: The bed guard is intended for use for children
between 18 months and 5 years of age, who are able to climb
on and off the bed without their parents' help.
WARNING: The bed guard must not be used to replace the cot,
since it does not guarantee the same safety standards.
WARNING: The fixing, fitting and adjustment operations of the
bed guard must only be carried out by an adult.
Ensure that the people using the bed guard know how to use
it safely.
WARNING: Before assembly, check that the product and all its
components have not been damaged during transportation.
Should any part be damaged, do not use and keep out of reach
of children.
WARNING: The fastening straps must never be removed from
the plastic supports and left within the reach of newborn babies
and children.
WARNING: Do not use accessories, spare parts, or any
component not supplied or approved by the manufacturer, as
they may make the bed guard unsafe.
WARNING: To prevent the risk of stangulation it is essential to
ensure that when the bedguard is fitted into position, there is
a gap of at least 250 mm (10 in.) between each end of the bed
and the corresponding end of the bedguard (diagram 3B).
WARNING: Do not use the safety Bedguard unless all the
components are correctly fitted and adjusted
WARNING: Never use without the fastening straps firmly fixed
to the bed
WARNING: Ensure that during use, the bed guard mesh is in
contact with the mattress side surface.
WARNING: The bed guard must not be used with beds in which
the top surface of the mattress is higher than 60 cm above the
floor.
WARNING: Do not use the bed guard with mattresses thicker
than 20 cm.
WARNING: The bed guard must not be used by adults, bed-
ridden people or the elderly, or in a non-domestic environment.
WARNING: do not use the bed guard if any part is broken, torn
or missing
WARNING: Do not let other children play unattended close to
the bed guard or climb on it.
WARNING: To prevent the risk of burns or fire, never place the
bed guard near electrical appliances, gas cooker or other sources
of intense heat. Keep the bed guard away from electrical cables.
WARNING: Do not place the bed guard near windows or
walls, where strings, curtains or other objects may be used by
the child to climb out of the bed, and to prevent the risk of
suffocation and/or chocking.
WARNING: Do not leave the bed guard under the sun for a
long time: prolonged exposure to direct sunlight may cause the
materials or fabric cover to fade.
WARNING: When folded store away from children.
WARNING: Do not use the Barrier on the top section of the
structure when used as bunk beds.
WARNING: Use of the Barrier is not recommended with low
density mattresses.
WARNING: The Barrier must not be used on beds with side
panels.
WARNING: The use of the bedguard (95cm) is allowed
with mattresses: Length 150-250cm / Width minimum
90cm / Height maximum 20cm. Do not use the bedguard
with mattresses thicker than 20cm.
WARNING: The use of the bedguard (135cm) is allowed
with mattresses: Length 190-250cm / Width minimum
90cm / Height maximum 20cm. Do not use the bedguard
with mattresses thicker than 20cm.
A- Bed guard
B- Safety mesh
C- Side joint
D-Plastic supports
E- Fastening straps
CLEANING AND MAINTENANCE
The cleaning and maintenance of the bed guard must only
be carried out by an adult.
Cleaning
Clean the fabric parts with a soft cloth soaked in water or a
neutral detergent.
Clean the plastic parts with a soft cloth soaked in water.
If the bed guard comes into contact with water, dry the
metal parts to prevent the formation of rust.
Never use abrasive detergents or solvents.
Maintenance
Periodically check that the bed guard components are not
worn, broken or damaged; in such an event, do not use the
bed guard before having repaired or substituted the worn
or damaged part.
Keep the bed guard in a dry place.
INSTRUCTIONS FOR USE
Turn the two plastic supports in a perpendicular position
with respect to safety mesh (diagram 1).
Push the safety mesh in a downward direction and lock it to
the two plastic supports, in the position corresponding to
the side joints (diagram 2).
Position the bed guard under the mattress, and fix it to the
bed with the two fastening straps (diagram 3A, diagram
3B).
To recline the bed guard without removing it from the bed,
release the safety mesh, first from one side and then from
the other, and then pull it in an upward direction (diagram
4A). The bed guard can now be reclined (diagram 4B).FOR
FURTHER INFORMATION, PLEASE CONTACT:
Chicco UK Ltd
Prospect Close
Lowmoor Road Business Park
Kirkby in Ashfield
Nottinghamshire NG17 7LF
Customer Services Helpline Tel: 01623 750870
(office hours only)
www.chicco.com
9
COMPONENTS
Advertisement
