Advertisement
Available languages
Available languages
Chicco Band Baby Walker
GB
• IMPORTANT: READ THE INSTRUCTIONS CAREFULLy
BEFORE USE AND KEEP THEM FOR FUTURE REFER-
ENCE. THE CHILD MAy BE HURT IF yOU DO NOT
FOLLOW THESE INSTRUCTIONS
• W ARNING: BEFORE FIRST USE, REMOVE AND DIS-
POSE OF ALL PLASTIC BAGS AND PACKAGING MA-
TERIALS AND KEEP THEM OUT OF REACH OF CHIL-
DREN.
WARNINGS
• W ARNING:Before first use, check that the product
and all its components show no signs of damage
caused by transportation. Check the product regu-
larly for signs of wear and damage. Keep all damaged
parts out of children's reach.
• W ARNING: This product must only be assembled by
an adult. Follow the instructions below to guarantee
correct assembly of all the components.
• W ARNING: Never leave your child unattended.
• W ARNING : The child will be able to reach further and
move rapidly when in the baby walking frame.
• W ARNING: prevent access to stairs, steps and uneven
surfaces.
• WARNING: guard all fires, heating and cooking ap-
pliances.
• WARNING: remove hot liquids, electrical flexes and
other potential hazards from reach.
• W ARNING: Prevent collisions with glass in doors, win-
dows and furniture.
• W ARNING: do not use the baby walking frame if any
components are broken or missing.
• WARNING: this baby walking frame should be used
only for short periods of time (e.g. 20 min).
• WARNING: this baby walking frame is intended to be
used by children who can sit unaided, approximately
from 6 months. It is not intended for children weigh-
ing more than 12 kg.
• WARNING: do not use replacement parts other than
those approved by the manufacturer or distributor.
• WARNING: Before use, ensure that all the safety de-
vices are fitted and working correctly.
• WARNING: Keep your child away from all moving
parts whilst you adjust the baby walker.
• W ARNING: Do not use the baby walker for children
who are over 85 cm in height.
• WARNING: To avoid all risks of strangulation, never
give children objects with cords or strings attached,
or leave them within their reach. Watch out for cur-
tain and blind cords etc.
• W ARNING: Keep all plastic bags and small toys away
from children to prevent the risk of suffocation.
• WARNING: Never leave the product exposed to bad
weather or direct sunlight. If the stroller is left ex-
posed to direct sun light for a long time, allow it to
cool down before placing your child inside.
• W ARNING: Do not use this product in temperature of
under 5°C or on slippery and/or icy surfaces.
• WARNING: Do not use this walker as a sledge or life
saver ring.
• WARNING: Check the baby walker regularly for any
signs of wear and damage.
• WARNING: Prolonged exposure to sunlight can cause
the fabric to fade.
• WARNING: Always check that the stoppers are fitted
correctly and show no sign of wear or tear.
• WARNING: When not in use, store the walker in a
suitable place, away from contact with all weather
conditions and out of the reach of children.
• WARNING: Do not allow other children to climb into
or play unsupervised near the walker.
CLEANING AND MAINTENANCE
• This product requires periodic maintenance. The clean-
ing and maintenance operations must only be carried
out by an adult.
• Use a soft damp cloth to clean the fabric, plastic parts
and the stoppers.
• Do not clean the product with abrasive products or sol-
vents.
• Always dry the metal parts to prevent the formation of rust.
CHICCO BAND BABy WALKER
Parts
a) Baby walking frame
b) Padded seat
c) Rigid backrest
d) 2 front swivel wheels
e) 2 rear fixed wheels
f) 6 stoppers
g) Large spoiler
h) E lectronic toy. (NB: the electronic play panel in-
cluded in the pack may be different from the one
illustrated in Fig. h).
i) 2 fastener straps
HOW TO ASSEMBLE THE BABY WALKING FRAME
1. Turn the baby-walking frame (a) upside down. Fit the
wheels (d) in the appropriate housings using the plastic
tool, as shown in diagram 1. Ensure that the wheels'
male securing pin is safely locked into position in each
housing.
2. Fit the rear wheels (e) in the appropriate housings as
shown in diagram 2. Ensure that the wheels' male se-
curing pin is safely locked into position in each housing:
you will hear it click into place and the rod connector
pin will now be visible.
3. Fit the stoppers (f) into the appropriate housings, as
shown in diagram 3A. Ensure that the joints of all the
stoppers are firmly and correctly fitted to the end (dia-
gram 3B).
4. Position the baby walker ready for use with all wheels
firmly on the floor (horizontal surface); lift the tray
slightly as seen in diagram 4, pulling it upwards until
you hear it click into position at the desired height.
WARNING: Before placing the child in the baby-walk-
ing frame, ensure that the blue button, located under
the small table, is safely locked: a click will be heard,
indicating that the button is locked into position.
See diagram 5.
5. Slide the front section of the rigid backrest into the
slots on the top end of the structure (A) and push
downwards until you hear it click into position (dia-
gram 6).
6. Insert the plastic rings of the padded seat (b) in the
slots located along the upper edge of the baby-walking
frame (diagram 7A), and ensure that they are correctly
locked in the position, as shown in the diagram 7B.
7. Slide the front section of the rear spoiler into the slots
on the top end of the structure (a) and push down-
wards until you hear it click into position. (diagram 8).
WARNING: Once the spoiler has been inserted, it can-
not be removed again. Do not attempt to remove it
using screwdrivers or other tools.
8. The electronic play panel has sounds and light effects
and can be fitted onto the baby walker tray by applying
a little pressure; it does not require any fastener device.
Batteries are not included; the game has two slots on
the bottom so you can use the straps in the pack to
fasten it onto structures, other than the baby walker
10
Advertisement
