Table of Contents
Advertisement
Quick Links
Smart Analog IC101
Smart Analog Easy Starter 101 Tutorial (RL78/L13)
Introduction
This application note is a tutorial that explains the setup routine required for enabling transmission between the Smart
Analog Easy Starter 101 (herein referred to as Easy Starter 101), which is the GUI tool for Smart Analog IC101
evaluations, and the CPU board included in the Renesas Starter Kit for RL78/L13, which connects to the Smart Analog
IC RSK Option Evaluation Board.
Note: Smart Analog IC101 is referred to as "SAIC101" throughout this document.
Target Board
Smart Analog IC RSK Option Evaluation Board [TSA-OP-IC101], Renesas Starter Kit for RL78/L13
[R0K5010WMS900BE] CPU board
Operation Confirmation Device
Smart Analog IC 101(part name: RAA730101), RL78/L13 (part name: R5F10WMGAFB)
Contents
1.
What You Will Need ........................................................................................................ 2
2.
Board Soldering ............................................................................................................. 3
3.
Jumper Confirmation ..................................................................................................... 5
4.
RSK CPU Board and TSA-OP-IC101 Board Connection .............................................. 7
5.
Firmware ......................................................................................................................... 8
5.1
Download ..................................................................................................................................... 8
5.2
Write ............................................................................................................................................. 8
6.
Serial Connection ........................................................................................................... 9
6.1
Power Supply Cable Connection ............................................................................................... 9
6.2
Serial Cable Connection ........................................................................................................... 10
6.3
COM Port Number Confirmation.............................................................................................. 11
7.
Smart Analog Easy Starter 101 ................................................................................... 12
7.1
Startup ........................................................................................................................................ 12
7.2
Serial Port Manual Settings ...................................................................................................... 12
7.3
Read Setting File ....................................................................................................................... 13
7.4
Operation Confirmation ............................................................................................................ 15
7.5
Output AFE Register File .......................................................................................................... 17
7.6
Conclusion ................................................................................................................................. 17
R21AN0011EJ0100 Rev.1.00
Nov 01, 2014
APPLICATION NOTE
R21AN0011EJ0100
Rev.1.00
Nov 01, 2014
Page 1 of 18
Advertisement
Table of Contents
Related Manuals for Renesas Smart Analog IC101
Summary of Contents for Renesas Smart Analog IC101
-
Page 1: Table Of Contents
This application note is a tutorial that explains the setup routine required for enabling transmission between the Smart Analog Easy Starter 101 (herein referred to as Easy Starter 101), which is the GUI tool for Smart Analog IC101 evaluations, and the CPU board included in the Renesas Starter Kit for RL78/L13, which connects to the Smart Analog IC RSK Option Evaluation Board. -
Page 2: What You Will Need
Plug diameter: 2.1 mm; Center Plus DC 5V Note: For connecting LCD extension board (Renesas Starter Kit LCD Application Board V2). As Easy Starter 101 does not use the LCD extension board, confirmation is not necessary unless other operations require it. -
Page 3: Board Soldering
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) Board Soldering To connect the RSK CPU board and the TSA-OP-IC101 board, the user must attach pin sockets or headers to the extension board interface (herein referred to as “application header”). This section explains the soldering locations on both boards. - Page 4 JA5 (facing JA1 (facing downward) downward) Figure 2-1 TSA-OP-IC101 Board Pin Header/Socket Mounting Note: Easy Starter 101 does not use the LCD extension board (Renesas Starter Kit LCD Application Board V2). R21AN0011EJ0100 Rev.1.00 Page 4 of 18 Nov 01, 2014...
-
Page 5: Jumper Confirmation
RSK CPU Board Use the initial settings to set the RSK CPU board jumpers. For details, refer to the User’s Manual (R20UT2125EG) for the Renesas Starter Kit for RL78/L13. 1-2 short Figure 3-1 RSK CPU Board Jumper Settings... - Page 6 Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) TSA-OP-IC101 Board Set the power supply, serial jumpers, etc., referring to Figure 3-2 and Table 3-2 for details. 1-2 short JP4 open JP2 short JP5 open JP3 open JP8 short...
-
Page 7: Rsk Cpu Board And Tsa-Op-Ic101 Board Connection
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) RSK CPU Board and TSA-OP-IC101 Board Connection After mounting pin headers and pin sockets and setting jumpers on both boards, connect the corresponding application headers (JA1 JA1, JA2 JA2, JA5 JA5, and JA6 JA6). -
Page 8: Firmware
File name: RL78L13_RSK+TSA-OP-IC101_Hex.zip Write Use the Renesas Flash Programmer and On-chip Debugging Emulator E1 to write the firmware to the board. Refer to the Renesas Flash Programmer User’s Manual for details on writing. Operation Confirmation Device Smart Analog IC 101 (part name: RAA730101), RL78/L13 (part name: R5F10WMGAFB) -
Page 9: Serial Connection
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) Serial Connection Power Supply Cable Connection Power is supplied to the TSA-OP-IC101 board from the RSK CPU board. Connect the AC adapter and the RSK CPU board as shown in Figure 6-1. -
Page 10: Serial Cable Connection
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) Serial Cable Connection Connect the PC to the RS233 serial connector on the RSK CPU board with a serial cable. If your PC is equipped with a D-SUB 9 pin connector, you can use the RS-232C cable, as shown in Image 1 of Figure 6-2. If your PC does not have a D-SUB 9 pin connector, use a serial cable that supports D-SUB 9 pin connectors such as the USB serial conversion cable shown in Image 2 of Figure 6-2. -
Page 11: Com Port Number Confirmation
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) COM Port Number Confirmation If you do not know the serial port number (COM port number) connected to the RSK CPU board, confirm the number by referring to the device manager. -
Page 12: Smart Analog Easy Starter 101
Smart Analog Easy Starter 101 Startup Double click Start.exe located in the SA_Easy_Starter_101_Ver2.1.zip file to start Easy Starter 101. Download Easy Starter 101 from the Renesas Electronics website as specified below Smart Analog Easy Starter 101 download URL: http://www.renesas.com/smart_analog/down_load_101 File name: SA_Easy_Starter_101_Ver2.1.zip... -
Page 13: Read Setting File
The TSA-OP-IC101 board is equipped with a thermistor to be used as a sensor to confirm operations. The sensor’s Setting file required to run the thermistor can be downloaded from the Renesas Electronics website. Store the downloaded file in the register set folder. - Page 14 TSA-OP-IC101 boards in the Start window’s Target Board combo box, and click Select. When the target boards are successfully connected, the Main window is displayed. Register: RSK Option Board Thermistor 2014/08/08 18:00:57 Target Board: R0K5010WMC000BE+ TSA-OP-IC101 (RL78/L13 + Smart Analog IC101) Main window is displayed Figure 7-6 Setting File Selection...
-
Page 15: Operation Confirmation
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) Operation Confirmation Use the thermistor to confirm that the board and Easy Starter 101 are operating correctly. First, click Graph in the Main window frame to display the ADC Graph window. - Page 16 Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) After confirming operations as instructed above, confirm the change in waveform by changing the SAIC101 settings. First, change the value of AIN2OFT in the Chip Config window (sect. 7.3) to 1. This value is used to adjust the offset voltage.
-
Page 17: Output Afe Register File
Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) Output AFE Register File Store the SAIC101 device’s changed AFE register file (sect. 7.4) in an external file. This AFE register file can be reloaded from the Start window. The AFE register file contains the following information: register values set in the Chip Config window, A/D conversion setting values (frequency, number of conversions, channels) set in the Main window frame, and the author, date created, and description input in the Export window. - Page 18 Smart Analog IC101 Smart Analog Easy Starter 101 Tutorial (RL78/L13) Website and Support Renesas Electronics Website http://www.renesas.com/ Inquiries http://www.renesas.com/contact/ All trademarks and registered trademarks are the property of their respective owners. R21AN0011EJ0100 Rev.1.00 Page 18 of 18 Nov 01, 2014...
- Page 19 Revision History Description Rev. Date Page Summary Rev.1.00 Nov 01, 2014 First edition issued...
- Page 20 General Precautions in the Handling of MPU/MCU Products The following usage notes are applicable to all MPU/MCU products from Renesas. For detailed usage notes on the products covered by this document, refer to the relevant sections of the document as well as any technical updates that have been issued for the products.
- Page 21 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products.