Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tar River SAYA-505
Summary of Contents for Tar River SAYA-505
- Page 1 No Till Drill SAYA-505 & 507 Operator’s Manual Rev. 5/22...
- Page 2 No Till Drill SAYA-505, 507 Page left blank intentionally...
- Page 3 No Till Drill SAYA-505, 507 TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Tar River dealer. Read manual in- structions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Owner’s/Operator’s Manual are completed before releasing equipment to the owner.
-
Page 4: Table Of Contents
No Till Drill SAYA-505, 507 Table of Contents Introduction …………………………………………………………………………………………….. 5 Technical Specifications ……………………………………………………………………………….. 5 Safety …………………………………………………………………………………………………… 6 Safety Signal Words ……………………………………………………………………………………. 6 General Safety Guidelines ……………………………………………………………………………… 7 Safety Decal Care ………………………………………………………………………………………. 7 Before Operation ……………………………………………………………………………………….. 8 During Operation ……………………………………………………………………………………….. 9 Highway And Transport Operations ……………………………………………………………………... -
Page 5: Introduction
No Till Drill SAYA-505, 507 Introduction Thank you for purchasing your SAYA No-Till Drill. The SAYA is designed to be used in LIGHT DUTY no- till or prepared seeding conditions. It is important to properly maintain and keep in place all safety guards and shields that came with you machine. -
Page 6: Safety
No Till Drill SAYA-505, 507 Important Safety Information Safety It is important that you read the entire manual and to become familiar with this product before you begin using it. This product is designed for certain applications only. The manufacturer cannot be responsible for issues arising from modification. -
Page 7: General Safety Guidelines
No Till Drill SAYA-505, 507 Important Safety Information General Safety Guidelines Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. De- signers and manufacturers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment. -
Page 8: Before Operation
No Till Drill SAYA-505, 507 Important Safety Information How to install Safety Signs: Be sure that the installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper. -
Page 9: During Operation
No Till Drill SAYA-505, 507 Important Safety Information During Operation Children should not be allowed on the product. • Clear the area of small children and bystanders before moving the feeder. • If using a towing unit, securely attach feeder by using a hardened 3/4” pin, a metal retainer, and safety •... -
Page 10: Highway And Transport Operations
No Till Drill SAYA-505, 507 Important Safety Information Highway and Transport Operations Adopt safe driving practices. • Keep the brake pedals latched together at all times. Never use independent braking with machine in tow • as loss of control and/or upset of unit can result. - Page 11 No Till Drill SAYA-505, 507 Important Safety Information Highway and Transport Operations Maneuver the tractor or towing vehicle at safe speeds. • Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury or death. • Avoid loose fill, rocks and holes, they can be dangerous for equipment operation or movement.
-
Page 12: Assembly
No Till Drill SAYA-505, 507 Assembly Step 1: Carefully uncrate and remove all parts. Ensure the double disc openers and coulters are inline and set at their proper 7 1/2” spacing. Step 2: Mount hopper box with the lid opening facing the front of the implement. - Page 13 No Till Drill SAYA-505, 507 Assembly Step 5: Install seed cup bottoms and hoses to cups (23" in back - 28" in front). Step 6: Install A frame on inside of mounts. Step 7: Install lower hitch blocks. Note: Hitch Blocks (Item 60) are in the up position for shipping only (Fig.
- Page 14 No Till Drill SAYA-505, 507 Assembly Step 9: Rotate scraperboard down.
-
Page 15: Operating Instructions
No Till Drill SAYA-505, 507 Operating Instructions Before beginning work: Be sure all the seed cups completely close and open the same, so all cups are putting out the exact amount • of seed. If they are not in sync, one cup will put out more than others. -
Page 16: Seeding/Fertilizing Rate Adjustment Handle
No Till Drill SAYA-505, 507 Operating Instructions Seeding/Fertilizing rate adjustment handle: To adjust the fertilizer rate, you will need to adjust hand wheels (on each side of hopper). The seed/fertilize rate depends on the seed/fertilizer you want to plant, please refer to your seed/ fertilizer supplier’s chart to get the proper seed/fertilize rate. -
Page 17: Seed Cup Shutoff
No Till Drill SAYA-505, 507 Operating Instructions Seed cup shutoff: Depending on the crop being planted, it may be necessary to not disburse from all of the seed cups. This is eas- ily done by simply sliding the “Seed shut off flap” in and out. -
Page 18: Seed Depth Control
No Till Drill SAYA-505, 507 Operating Instructions Seed depth - Disc Support Bar The top link on the tractor hitch should be properly adjusted to carry the machine level in an operating posi- tion. During operation, the tractor lift must be fully lowered to allow the machine to follow the contour of the ground. -
Page 19: Lubrication And Maintenance
No Till Drill SAYA-505, 507 Lubrication and Maintenance Important: It is important to thoroughly clean the seeder after use. Failure to do so can cause irreparable dam- age to the seed cups and drive system. Grease and turn the Seed adjustment handle to ensure grease lubricates the threads. -
Page 20: Application Rate/Seed Charts
No Till Drill SAYA-505, 507 Setting Application Rates The most accurate way to set application rates is to drive a predetermined distance and physically catch the seeds dispensed. To do this, remove at least one drop hose and tie a plastic bag onto bottom of seed cup. -
Page 21: Torque Specifications
No Till Drill SAYA-505, 507 Application Rate Charts... - Page 22 No Till Drill SAYA-505, 507 Notes: This chart is an approximate estimate of torque values. Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual.
-
Page 23: Parts Breakdown
No Till Drill SAYA-505 & 507 Parts Manual Rev. 5/22... - Page 24 No Till Drill SAYA-505, 507 Hopper Assembly LH (rear) RH (front) Front cup box Rear cup box Note: The Rate adjustment plates are not the same. LH Note: Front and rear seed cup boxes can be identified plate faces the rear of the machine. The RH plate faces by examining the shafts.
- Page 25 No Till Drill SAYA-505, 507 Hopper Assembly Item Part # Description Qty. SA1003-55 Hopper; SAYA-505 SA1003-78 Hopper; SAYA-507 SA1001-55 Hopper lid; SAYA-505 SA1001-78 Hopper lid; SAYA-507 SA1004 Hopper end plate, LH SA1005 Hopper end plate, RH DL5003 Lid piston DL7001-L...
- Page 26 No Till Drill SAYA-505, 507 Hopper Assembly LH (rear) RH (front) Front cup box Rear cup box Note: The Rate adjustment plates are not the same. LH Note: Front and rear seed cup boxes can be identified plate faces the rear of the machine. The RH plate faces by examining the shafts.
- Page 27 No Till Drill SAYA-505, 507 Hopper Assembly Item Part # Description Qty. SA2005 Handle assembly SA2005K Locking knob SA5005K Spinning adjustment handle with hardware BM0812540 Bolt M8x1.25x40 DL7007 Waste/Seed/Fertilizer shut off flap DL5006 Handle, clean out DL4006 Rod, clean out...
- Page 28 No Till Drill SAYA-505, 507 Hopper Assembly LH (rear) RH (front) Front cup box Rear cup box Note: The Rate adjustment plates are not the same. LH Note: Front and rear seed cup boxes can be identified plate faces the rear of the machine. The RH plate faces by examining the shafts.
- Page 29 No Till Drill SAYA-505, 507 Hopper Assembly Item Part # Description Qty. SA4030 Flap outer SA4031 Flap inner SA4033 Agitator flange assembly w/bearing BM061020 Bolt HH M06-1.0x20 NM0610 Nut HH M06-1.0 FNM0610 Flange nut HH M06-1.0 BM0812540 Bolt HH M08-1.25x40 FNM08125 Flange nut HH M08-1.25...
- Page 30 No Till Drill SAYA-505, 507 Frame Assembly See note on page 13, Step 7. Disc Assembly - Front Disc Assembly - Rear SA7001F SA7001R See Note 2, page 35...
- Page 31 Scraper mount bracket BM0812520 Bolt M8-1.25x20 FN08125 Flanged nut M8-1.25 DL11012 Flap 7.25” (SAYA-505; 1 pc / SAYA-507; 3 pcs) DL11012A Flap 8.25” (SAYA-505; 5 pcs / SAYA-507; 6 pcs) DL11009 Spring, flap (SAYA-505; 6 pcs / SAYA-507; 9 pcs) BM0812550 Bolt M08-1.25x50...
- Page 32 No Till Drill SAYA-505, 507 Frame Assembly See note on page 13, Step 7. Disc Assembly - Front Disc Assembly - Front Disc Assembly - Rear Disc Assembly - Rear SA7001F SA7001F SA7001R SA7001R See Note 2, page 35 See Note 2, page 35...
- Page 33 No Till Drill SAYA-505, 507 Frame Assembly Item Part # Description Qty. SA9003 Adjustment shaft complete SA9002 Adjustment shaft wheel SA4009 A-frame vertical; SAYA-505&507 SA4004 Pin M22x110 BM182540 Bolt bottom M18-2.5x40 NM1825 Nut M18-2.5 SA4006 A-frame spacer BM1825110 Bolt bottom M18-2.5x110...
- Page 34 No Till Drill SAYA-505, 507 Frame Assembly Frame Assembly Frame Assembly See note on page 13, Step 7. Disc Assembly - Front Disc Assembly - Front Disc Assembly - Rear Disc Assembly - Rear SA7001F SA7001F SA7001R SA7001R See Note 2, page 35...
- Page 35 No Till Drill SAYA-505, 507 Frame Assembly Item Part # Description Qty. SA7001 Coulter disc complete LW18 Washer lock M18 FW18 Washer flat M18 SA4023 Damper rod SA4024 Damper guide SA4025 Star washer SA4026 Retainer clip CP2.5x20 Cotter pin M2.5x20...
- Page 36 No Till Drill SAYA-505, 507 Roller Assembly...
- Page 37 No Till Drill SAYA-505, 507 Roller Assembly Item Part # Description Qty. SA9001-55 Drive roller; SAYA-505 SA9001-78 Drive roller; SAYA-507 DL8008 Roller arm B60062RS Bearing 6006 2RS SRI-55 Snap ring, internal M55 DL10012 Dust roller cap DL11013 U-bolt M10 - 1.5 x 140...
- Page 38 No Till Drill SAYA-505, 507 Floorboard Assembly...
- Page 39 No Till Drill SAYA-505, 507 Floorboard Assembly Item Part # Description Qty. SA4039 Step board, rear - SAYA505 SA4042 Step board, rear - SAYA507 SA4037 Step board, LH front - SAYA505 SA4040 Step board, LH front - SAYA507 SA4038 Step board, RH front - SAYA505...
-
Page 40: Decals
No Till Drill SAYA-505, 507 Decals... - Page 41 Decal Warning, “Falling off tractor” RT-1005 Decal Warning, “To prevent serious injury or death” Decal1016 Decal Logo, “Tar River Implements” medium oblong D1005 Decal Warning, “Chemicals” (Note: see LH inside of hopper cover) D1224 Decal “Spreading Chart” (Note: see RH inside of hopper cover) RT1004E Decal Warning, “Do not open”...
- Page 42 No Till Drill SAYA-505, 507 Decals 2 - RT-1005 - Qty. 1 - 5SBD1005 - Qty. 1 3 - D1016 - Qty. 1 4 - 5SBD1004 - Qty. 1 5 - D1224 - Qty. 1 8 - Qty. 1 6 - RT1004E - Qty. 2 10 - Qty.
-
Page 43: Warranty
No Till Drill SAYA-505, 507 Warranty LIMITED WARRANTY Belco Resources Equipment warrants to the original purchaser of any new piece of machinery from Belco Re- sources Equipment, purchased from an authorized Belco Resources Equipment dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and mu- nicipalities’... - Page 44 No Till Drill SAYA-505, 507 401 Jeffreys Road Tel: 252-822-7140 Rocky Mount, NC 27804 Fax: 252-787-5855 www.tarrivermfg.com Sales@tarrivermfg.com...