Panasonic AJ AJ-HDX900 Operating Instructions Manual page 99

Chapter 6 Maintenance and inspections
6. SERVO
Indications on LCD "SERVO" display lights (during recording and
screen playback).
WARNING lamp Flashes four times a second (during recording
and playback).
Tally lamp Flashes four times a second (during recording
and playback).
Viewfinder "SERVO" display lights (during recording and
playback).
Alarm Sounds four times a second (during recording
and playback).
Warning description The servo is disturbed.
VTR unit operation Operation continues but the unit may not operate
correctly.
Corrective action Turn off the power and consult your dealer. The
warning display may flash for a moment and then
disappear when tape transport commences: this
is normal and not indicative of a failure or
malfunctioning.
7. RF
Indications on LCD "RF" display flashes (during standby and
screen recording).
WARNING lamp Flashes four times a second (during recording).
Tally lamp Flashes four times a second (during recording).
Viewfinder "RF" display lights (during recording).
Alarm Sounds four times a second (during recording).
Warning description The video heads have become clogged. There
is a problem in the video system.
VTR unit operation The cleaning rollers are activated to clean the
heads (for a maximum of 3 seconds).
Recording continues but the signals may not be
recorded correctly.
The indications on LCD screen are retained until
the REC/PAUSE status is established. They go
off as soon as the unit transfers from the
REC/PAUSE mode to another mode.
Corrective action Clean the heads.
recorded correctly even after cleaning, consult
your dealer.
8. WIRELESS RF
Indications on LCD No indication
screen
WARNING lamp Flashes four times a second (during standby and
recording).
Tally lamp Flashes four times a second (during recording).
Viewfinder "WIRELESS RF" display lights for at least 3
seconds during recording.
Alarm Sounds four times a second (for at least 3
seconds during standby and recording).
Warning description Poor wireless signal reception.
VTR unit operation Operation continues but the signals from the
wireless microphone cannot be received.
Corrective action Check the microphone's power supply and the
reception condition of the receiver.
9. BATTERY NEAR END
Indications on LCD
screen
WARNING lamp
Tally lamp
Viewfinder
Alarm
Warning description
VTR unit operation
Corrective action
10. TAPE NEAR END
Indications on LCD
screen
WARNING lamp
Tally lamp
Viewfinder
Alarm
Warning description
VTR unit operation
Corrective action
11. 1394
Indications on LCD
screen
WARNING lamp
Tally lamp
If the signals cannot be
Viewfinder
Alarm
Warning description
VTR unit operation
Corrective action
(continued)
The bar display that shows the remaining battery
charge starts flashing.
Flashes once a second.
Flashes once a second.
BATT LED starts flashing.
Sounds four times a second.
The battery charge is nearly depleted.
Operation continues.
Replace the battery when it becomes necessary.
The bar display that shows the remaining tape
amount starts flashing.
Flashes once a second (during recording).
Flashes once a second (during recording).
≥ The remaining tape display starts flashing (in
the EE mode).
≥ " = " flashes for 3 seconds one minute before
the tape reaches the end.
Sounds once a second.
The tape is close to its end (about 2 minutes
remain).
Operation continues.
Replace the cassette tape when it becomes
necessary.
"1394 E-22" display flashes.
Flashes four times a second.
Flashes four times a second.
When error code 92 appears, "1394 INITIAL
ERROR" display lights (during standby).
Sounds four times a second.
There is something wrong with the signals
supplied to the DVCPRO connector.
Operation continues, but something is wrong with
the signals supplied to the DVCPRO connector.
Check the IEEE 1394 cable and DVCPRO
connector connections and the settings of the
external units or menu settings, and then turn the
power off and back on.
If the warning display is not cleared, check "6-3-2
Error codes," and consult your dealer.
6
99