Subscribe to Our Youtube Channel
Related Manuals for Seko TEKNA EVO TPG
Summary of Contents for Seko TEKNA EVO TPG
- Page 1 TEKNAEVO TPG INSTALLATION MANUAL HANDBUCH MANUAL DE INSTALACION www.winwinpoolshop.com MANUEL D’INSTALLATION MANUALE D’INSTALLAZIONE MANUAL DE INSTALAÇÃO KULLANIM KLAVUZU РУКОВОДСТВО ПО УСТАНОВКЕ И ЭКСПЛУАТАЦИИ EM00136061 rev. 2.5...
- Page 2 Control panel – TEKNA TPG Access to the programming menu When pressed during the pump operation phase, it cyclically displays the programmed values on the display; When pressed at the same time keys, it increases or decreases a value dependent on the selected operating mode. During programming it carries out an “enter” function, meaning that it confirms entry to the various menu levels and modifications within the same.
-
Page 3: Setting Menu
Programming menu TPG You can access the programming menu by pressing the key for over three seconds. The keys can be used to run through the menu items, with the key being used to access changes. The pump is programmed in constant mode in the factory. The pump automatically returns to the operating mode after 1 minute of no activity. -
Page 4: Operation
Setting the Language Programming Operation PROG Makes it possible to select the language. The pump is set in Pump Functions English in the factory. Max flow rate Changes can be made by pressing the key, then P100% using the keys to set the new value. Press Alarm Relay confirm and return to the main menu N.Open... - Page 5 Display during Operation Display during Setting (MODE key) Operating mode Input mA FLOW sensor Programmed value Displays the Low and High Operating mode value status Programmed interval value value in sequence (default: 4-20) 4-20 Stop P100% 0.0 mA P100% Current dosage value...
- Page 6 Display during Operation Display during Setting (MODE key) Displays programmed FLOW Memory timeout sensor function Operating mode status status Programmed 1:n = impulse value of n multiplication Timeout Stop Current dosage value Alarms and statuses Displays stroke Lev = Level alarm countdown Current dosage value...
- Page 7 Display during Operation Display during Setting (MODE key) FLOW Memory Operating mode sensor function Displays in sequence: quantity to Operating mode status status Programmed value be dosed, dosage time and pump Batch Quantity in ml frequency Batch 7.0ml Q.ty 7.0ml...
- Page 8 Paragraph 8 – Timed Dosage (Frequency signal input “TRIGGER” activated) Programming Operation After receipt of the TRIGGER signal set, the pump doses a quantity that can be programmed in ml. It is possible to set a delay time before the dosing (Delay) and the interval between subsequent dosings (Interv.) as illustrated in the diagram: Trigger Quantity...
- Page 9 Paragraph 8 – Timed Dosage (Frequency signal input “TRIGGER” not activated) Programming Operation The pump doses a programmed quantity in ml. It is possible to set a PROG pump delay time (Delay) when the pump is started and an interval between two successive dosings (Interval), as illustrated in the Configuration diagram:...
- Page 10 Paragraph 10 – Setting the Alarm Relay Programming Operation PROG In the absence of an alarm situation, it can be set as open (default) or closed. Pump Functions Changes can be made by pressing the key, then using Max flow rate P100% keys to set the new value.
- Page 11 Paragraph 13 – Password Programming Operation PROG By entering the password, you can enter the programming menu and see all the set values. The password will be requested whenever you seek to modify them. The flashing line indicates the number than can be modified. Use the key to select the number (from 1 to 9), and the Password...
- Page 12 Paragraph 17 - Setting the Pause Programming Operation PROG The pump can be paused by remote input. The factory setting is Normally Open. Configuration Changes can be made by pressing the key, then Paus using the keys to set the new value ( N. OPEN or N.Open N.
Need help?
Do you have a question about the TEKNA EVO TPG and is the answer not in the manual?
Questions and answers