Table of Contents
Advertisement
INSTALLATION
General
Hatco
Pickup Pods are shipped mostly assembled. Care
®
should be taken when unpacking the shipping carton to avoid
damage to the unit. Use the following procedures to complete
assembly and install a Pickup Pod.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors in a temperature-controlled
environment.
Locate unit in an area that is convenient for use. Location
should be level to prevent unit or its contents from falling
accidentally and strong enough to support weight of unit
and contents.
NOTICE
Unit must be level for doors to function properly.
Do not lay unit on its front side. Damage to doors could
occur.
NOTE: Due to the size and weight of the unit, use the proper
number of people for installation based on the weight
of the unit.
1. Inspect the shipping container for obvious signs of transit
damage. If damaged, take photos of the damage and
inform the freight company immediately. CAUTION! Stop!
Do not attempt to use a damaged unit. Contact Hatco
for assistance.
2. Move the unit close to the final installation location.
• The unit is shipped in a horizontal position, and will need
to be tipped up to its normal, vertical position. Make
sure there is enough space to tip up the unit near the
installation location.
3. Cut and remove the shipping bands from around the
packaging, then remove the packaging.
4. Remove any loose components/accessories from the
shipping container. The following loose components are
included in an "Accessory" box in every Hatco Pickup Pod:
• Power cord
• Wall anchoring hardware kit
• Antennas
NOTE: The leveling feet on the pickup pod are metal. To
prevent scratching the floor, be very careful while
moving the unit during installation. Consider placing
something underneath the unit to protect the floor.
5. With the help of several people, carefully tip up the unit to
its vertical position.
6. Remove the tape and protective packaging from all
surfaces of the unit.
7. Inspect the unit for freight damage such as dents or
scratches on the exterior, doors, or inside the cubbies.
If damaged, take photos of the damage and inform the
freight company immediately.
CAUTION
8. Perform the "Installing the Pickup Pod" procedure.
9. Perform the "Setting up the Pickup Pod for Operation"
procedure.
Installing the Pickup Pod
The Pickup Pod is a floor standing unit that needs to be secured
to a wall using the wall anchoring bracket. Use the following
procedures to install a Pickup Pod in an appropriate location.
Tools Required
#2 Phillips Screwdriver
Level
Cordless Drill
Hammer
Positioning the Pickup Pod
Use extreme caution when moving and tipping unit during
installation. Size and weight of unit create significant tip
and pinch point hazards. Remain aware and keep clear of
unit/pinch points while tipping to avoid serious injury.
1. Using the appropriate number of people, place the unit in
the desired location.
• Locate the unit indoors in a temperature-controlled
environment and in an area that is convenient for use.
Installation locations above ground and near windows
will allow for better cellular connectivity.
• Make sure the floor is level and the unit is placed in front
of an appropriate wall for installation of the anti-tip wall
anchoring bracket.
• Make sure a grounded electrical receptacle of the
correct voltage, size, and plug configurationis is within
three feet of the unit on the installation wall.
• Make sure the cellular signal in the installation location
is three bars or higher for all major mobile service
providers. Users and delivery workers will be using
mobile devices to open the cubby doors.
2. Level the unit, if necessary.
a. Remove the two (2) screws that secure the top access
panel to the unit. Remove the panel. WARNING!
ELECTRIC SHOCK HAZARD—Removing top access
panel exposes electrical components. Make sure
power switch is OFF and unit is unplugged before
removing panel.
b. Pull up on the door release ring located just below the
front, center of the top opening. All the cubby doors will
open.
6
Flat Head Screwdriver
1/4" Hex Wrench
5/16" Drill Bit
Step Ladder
WARNING
HPPM-0422
Advertisement
Table of Contents
