Table of Contents
Advertisement
UPRIG HT ANTI-TIP BR ACKE T INS TALL ATION
JOINING KIT INS TALL ATION
ANTI-TIP BR ACKE T KIT:
Kit Sizes: 60" (1524 mm) / 72" (1828.8 mm) / 78" (1981.2 mm) / 90" (2286 mm)
• One (1) anti-tip bracket (Figure 1.1)
K I T C ON T EN T S
• Four (4) masonry 3/16" screws
• Eight (8) wood #12 – 2" screws
• (1) Joining Rainshield Assembly
• Twelve (12) 1/4" washers
• (1) Joining Kickplate
FOR ALL FULL SIZE RESIDENTIAL MODELS, THE ANTI-
TIP BRACKET ENGAGES WITH THE REAR LEVELING
• Anti-Sweat Foam End Panels*
LEGS TO SECURE THE UNIT. FOLLOW THESE STEPS
TO SECURE THE BRACKET BEFORE MOVING THE
• Joining Bracket*
UNIT INTO FINAL OPERATING POSITION.
• 1/4-20 x 1" Hex Head Screws*
1. Determine final location of the unit. For a FLUSH
install, measure back 24-31/32" (Dimension A)
• 1/4" Split Lock Washers*
from the surrounding cabinetry. For a PROUD
*Quantities vary by kit size.
install, measure back 22-31/32" (Dimension B)
from the surrounding cabinetry. For either type of
install, place the anti-tip bracket centered in the
R EQUIR ED T O O L S
rough opening.
Required tools include (but may not be limited to) the
WARNING: To avoid a hazard due to instability of
the appliance, it must be fixed in accordance with
following:
the instructions.
• Phillips Bit Driver or Screwdriver
AVERTISSEMENT: Pour éviter tout risque dú a
l´instabilité del l´appareil, vous devez le fixer
• 7/16" Socket Wrench
conformément aux instructions.
• 1/4" Socket Wrench
30 INCH UNIT
• Tape
• Marking Utensil
• Drill
NO T E: M A K E SUR E T HE A N T I -T IP BR A CK E T S
A R E IN S TA L L ED P ER IN S TA L L AT ION M A NUA L
IN S T RUC T ION S. E A CH UNI T W IL L A L S O NEED
T O BE P R OP ER LY L E V EL ED P ER IN S TA L L AT ION
M A NUA L IN S T RUC T ION S.
CAUTION!
Electrical shock or burn hazard.
Unplug the unit or turn off the power
supply before proceeding.
WARNING! TIP OVER HAZARD.
hazards from appliance instability, be sure
to install the anti-tip brackets (see fig. 1)
on each individual unit per the installation
manual instructions.
Page 26 of 48
T RUE RE S ID E N TI A L
I N S T A L L A T I O N
TRUE RESIDENTIAL REFRIGERATION
R
9 9/32"
236mm
22 31/32"
583mm
PROUD INSTALL
To avoid
®
2. Using the bracket as a guide, drill pilot holes into the
wall/floor. It is recommended to secure the bracket
to as many floor joists and wall studs as possible.
WARNING! TIP OVER HAZARD.
3. Using the provided screws and washers, secure the
adult could tip the appliance, resulting in
bracket to the wall/floor. Adjust the rear rollers to
property damage or bodily harm. Follow
just above their lowest position and move the unit to
these instructions to properly install
its final position. Raise the rear rollers a minimum
of 1/8" to engage the bracket.
the anti-tip device. If the appliance is moved, verify
that the device is properly engaged before the normal
usage of the appliance commences.
FIGURE 1.1 - ANTI-TIP BRACKET
FIG. 1.
Anti-tip bracket. Be sure to install a bracket for each unit.
C L
C L
FIG. 2.
Pull the rainshield open.
FIG. 3.
Locate the reed switch in the bottom of the rainshield.
FIG. 4.
Remove the plastic cover.
03/31/2022
987036
5.19.17 AL
TR-30REF-R-SG-A
N O T E : D I M E N S I O N S M AY VA R Y B Y ±
9 9/32"
236mm
24 31/32"
634mm
FLUSH INSTALL
TEC_TM_065 REV. B
A child or
/
"
1
8
Advertisement
Table of Contents
