Table of Contents
Advertisement
•
Position the right edge of media between the media
loading mark and the right edge of label.
2
No.
Name
No.
1
Media loading mark
2
NOTE
When setting the roll media, set both sides of the
media at least 5 mm away from the edge of the
pressurizing roller.
Slippage or creases may occur during printing.
Adequate
Not adequate
2
1
5mm 5mm
5mm
No.
Name
No.
1
Roll media
2
8. If the edge of the roll media is set less than 5 mm
from the edge of the pressurizing roller, follow the
procedure below to adjust the position of the roll
media.
a. Loosen the fixing levers of the right and left roll
media holders, and move the roll media to left or
right.
b. After moving the roll media, fix it with fixing
levers of the right and left roll media holders.
NOTE
Fix the roll media holders by pressing the holders
to the printer.
If you have moved the roll media to the sides,
repeat the steps 5 to 7.
4
1
3
3
No.
Name
No.
3
1
Roll media holder (Left)
2
Roll media holder (Right)
4
9. Lower Front media loading lever (raise Rear media
loading lever).
2
No.
Name
No.
1
Front media loading
2
lever
NOTE
Push Front media loading lever down and lower
it firmly.
For Rear media loading lever, push it up firmly.
If the lever is not firmly lowered or raised, the
media may not be detected.
When loading the new roll media, cut the front
1
edge of the media if it is not straight.
Name
Label
10. Close the front cover.
Not adequate
No.
1
2
2
・The procedure for setting roll media is complete.
1
1
5mm
Name
10 Checking print conditions
Pressurizing rollers
Check the condition of the print head after the ink
charging.
NOTE
When using 6-color set, use transparent media or
colored media.
When you are using 6-color set and printing on
white media, read "3.6.2 Nozzle check B" in the
Operation Manual.
1. Turn ON the printer and load the media.
"9 Loading media"
2. Confirm that the printer functions normally.
3. Press the [<] key on the operation panel for two
seconds or more.
2
3
4
Name
Roll media
Fixing lever
・Nozzle check printing starts.
CAUTION
UV emitted from this product.
1
Eye or skin irritation may result from
exposure.
Use appropriate shielding.
Name
Rear media loading lever
Operation Manual "4.4.3 Cutting media"
1
Name
No.
Name
Front cover
13
VJ-1638UH MarkⅡ INSTALLATION MANUAL
4. Check the print result for blurred or missing parts
in the check pattern.
No nozzle clog
Nozzle clogged
5. Check the sample print for blurred or missing
parts in the check pattern.
• Press and hold the [Cleaning] key on the operation
panel for two seconds or more.
• "Cleaning **%" is displayed on the operation panel.
6. Head cleaning starts.
NOTE
If one time of head cleaning was not enough to
remove blurred or missing parts in the check
pattern, perform "Long" cleaning.
If those problems above were not improved after a
few times of head cleaning, refer to the Operation
Manual "7 Troubleshooting" and perform required
procedures.
7. Perform nozzle check again and check the
condition of the print head.
11 Manual composition
This product includes the following manuals.
・Installation Manual (this manual)
This manual explains the procedures of
unpacking, assembling, installing, and the
basic set up.
・Product Activation Guide*
This manual explains the procedures when the
printer starts up first time.
・Operation Manual*
The Operation Manual explains the basic
installation, daily use and applicable functions.
*Please download from the MUTOH Club:
https://club.mutoh.co.jp/mutoh/guser
TIP
Operation Manual of this product is created with
PDF format.
Adobe Acrobat Reader 5.0 or above is required to
view PDF format. Adobe Reader is available for
free download at Adobe's website.
VJ1638UH2E-I-02
Advertisement
Table of Contents
