Hookup Diagrams; Quick Start - Mackie SRM350 Owner's Manual

HOOKUP DIAGRAMS

Quick Start

1. Start with the following settings on the back of the
SRM350v2:
Turn the POWER switch off (down).
Set the CONTOUR and MIC/LINE switches out. If using
a microphone as the input to the SRM350v2, push the
MIC/LINE switch in.
WARNING: Turn the LEVEL control
down (counterclockwise) before every
use. If not, you could be in for a
startling surprise, especially if the
last time you used it was with a
microphone and now you want to
connect a line-level source.
2. Connect the output from your signal source (mixing
console, microphone, preamp, or other mic- or line-
level source) directly to the INPUT connector on the
back of the SRM350v2. This is a combination XLR and
1/4" TRS connector, and accepts balanced or
unbalanced line-level signals from mixers,
preamplifiers, CD players, tape
decks, etc., with the MIC/LINE
switch out, and accepts direct
connections from dynamic
microphones with the MIC/LINE
switch pushed in.
6
POWER
SRM350v2: STEREO OPERATION WITH A MIXER
3. Connect the supplied AC power cord to the IEC socket
on the back of the SRM350v2. Plug the other end into an
AC outlet properly configured with the correct voltage
for your particular model.
4. Turn on your signal source. Make sure its Master
Volume control (if it has one) is turned all the
way down.
5. Turn on the SRM350v2 POWER switch.
6. Start the signal source, whether it be speaking into a
microphone or starting a CD player. Adjust any volume
controls on the signal source for normal operation.
7. Slowly turn up the LEVEL control on the back of the
SRM350v2 until the desired volume is reached (and the
LIMIT light does not come on). Always wear hearing
protectors if you are close when it is playing at high
levels.
8. If there is no sound, always turn down the SRM350v2
LEVEL control before investigating. There may be a
mixer or preamplifier mute or tape switch engaged, or a
mic switch off.
SIGNAL LIMIT
NORMAL
+45
O O
+5dB
LEVEL
LINE
100Hz 12k/AIR
MIC
CONTOUR
POWER
(+3dB)
THRU
INPUT
From Mixer
Left Output
1
1
LINE
GAIN
EQ
HIGH
MID
LOW
AUX
1
2
PAN
MUTE
SOLO
1
(Mackie Onyx 1220i shown)
SIGNAL LIMIT
NORMAL
+45
O O
+5dB
LEVEL
LINE
100Hz 12k/AIR
MIC
CONTOUR
(+3dB)
THRU
INPUT
From Mixer
Right Output
2 3 4
CTRL - RM OUT MAIN OUT ALT 3-4 OUT TAPE
L
IN OUT
L R L R L/3 R/4 R
LINE IN 5-6 LINE IN 7-8 LINE IN 9-10 LINE IN 11-12
2 3 4 L L L L
LINE LINE LINE
R
R R R
CTRL ROOM/PHONES
SOURCE
L R
GAIN GAIN GAIN GAIN GAIN GAIN GAIN
EQ EQ EQ
EQ EQ EQ
HIGH HIGH HIGH HIGH HIGH HIGH HIGH
MID MID MID MID
MID MID MID
RUDE
CONTROL PHONES
SOLO
ROOM
LOW LOW LOW LOW LOW LOW LOW
AUX MASTER
RETURN
AUX AUX AUX AUX AUX AUX AUX SEND
1 1 1 1 1 1 1 1 1
2 2 2 2 2 2 2 2 2
PAN PAN PAN PAN PAN PAN PAN
POWER
MUTE MUTE MUTE MUTE MUTE MUTE MUTE
MIC
SOLO SOLO SOLO SOLO SOLO SOLO SOLO
2 3 4 5-6 7-8 9-10 11-12 TALKBACK MAIN MIX
Mixing Console