Dexter Laundry V-Series Manual
  1. Manuals
  2. Brands
  3. Dexter Laundry Manuals
  4. Washer
  5. V-Series
  6. Manual

Dexter Laundry V-Series Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

USE THE BLUE TABS LOCATED ON THE
RIGHT AND LEFT SIDES OF THE FOLLOWING
DOCUMENT TO ADVANCE TO EACH SECTION.
8533-050-001 1/22

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V-Series and is the answer not in the manual?

Questions and answers

Related Manuals for Dexter Laundry V-Series

Summary of Contents for Dexter Laundry V-Series

  • Page 1 USE THE BLUE TABS LOCATED ON THE RIGHT AND LEFT SIDES OF THE FOLLOWING DOCUMENT TO ADVANCE TO EACH SECTION. 8533-050-001 1/22...
  • Page 2 Use safety consciousness when placing or moving your hands while working in the interior of this equipment. V-Series Vended Washers WCVD-18, WCVD-25, WCVD-40, Caution! To reduce the risk of damage to the Water Inlet WCVD-55, WCVD-75 Valve, do not supply inlet water with a temperature that exceeds 70˚...
  • Page 3 Equipment Safety Warnings Indicates an imminently hazardous situation, Symbols and Terminology Used in this Equipment which if not avoided, will result in death or seri- ous injury. Indicates a potentially hazardous situation, Warning! Do not operate equipment if door glass is which if not avoided could result in death or damaged in any way.
  • Page 4 WARNING WARNING • All washers must be installed in accordance to all applicable electrical, plumbing and all other local codes. Children should be supervised to ensure they do not operate or play • These installation and operation instructions are in or around equipment. for use by qualified personnel only.
  • Page 5 Warning! Do not operate equipment if door glass is Prohibited! Do not attempt to open, touch, or pro- damaged in any way. ceed before referring to the manual or unless quali- fied. Mandatory! Read all supporting documentation be- Warning! Keep clear of rotating parts. fore operating or maintaining equipment.

  • Page 6: Table Of Contents

    Loading Door Removal ......56-57 Guidelines Parts Data Loading Door Hinge Removal .....56-57 Section 1: Loading Door Disassembly ......56-57 V-Series Accessories ........92 Machine Specifications & Mounting Loading Door Reassembly ......56-57 Wiring Harness Part # by Model ....95 WARNING Specifications..........15 Control Panel Name Plate Decal ......57...
  • Page 7 Notes Notes Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...

  • Page 8: Machine Specifications & Mounting

    Specifications for below models are outlined in this book: WCVD18KCS-10 120 volt 60hz Single Phase WCVD18KCS-12 208-240 volts 60hz Single Phase or Three Phase WCVD25KCS-12 208-240 volts 60hz Single Phase or Three Phase WCVD40KCS-12 208-240 volts 60hz Single Phase or Three Phase WCVD55KCS-12 208-240 volts 60hz...

  • Page 9: Mounting Dimensions

    T-300 Mounting Dimensions T-400 Mounting Dimensions Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 10 T-600 Mounting Dimensions T-900 Mounting Dimensions Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 11 T-1200 Mounting Dimensions T-300 Mounting Pad Dimensions Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 12 T-600 Mounting Pad Dimensions T-400 Mounting Pad Dimensions Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 13 T-900 Mounting Pad Dimensions T-1200 Mounting Pad Dimensions Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...

  • Page 14: Machine Installation & Operating Instructions

    Notes Section 2: Machine Installation & Operating Instructions Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 15 Installation & Operation To Make Electrical Connections Disconnect all power to the washer. Remove screw and lift out the cover located in the upper left corner All washers must be installed in accordance with all local, state and national building, of the machine (as viewed from the back).
  • Page 16 TRANSIENT VOLTAGE SURGE SUPPRESSORS Operating Instructions Like most electrical equipment your new machine can be damaged or have its life shortened by voltage Microprocessor surges due to lightning strikes which are not covered by factory warranty. Local power distribution Prior to operation, the micro computer should be set to display the amount of vend price being offered problems also can be detrimental to the life of electrical components.

  • Page 17: Machine Programming Instructions

    PROGRAMMING INSTRUCTIONS: The washer has two levels of programming. The Washer Cycle Programming allows the owner complete access to the wash cycle parameters – add/remove a bath, bath times, spin times, water temperatures, etc. The Coin/Price Programming allows the owner to set the price for the washer features and the values of the coins.
  • Page 18 Washer Temperature Pricing: WASH CYCLE PROGRAMMING: The washer can be set for different levels of pricing for Cold, Warm and Hot water. The Cold water setting To change a feature of the wash cycle, push and hold the Hot temperature button and then push the is considered as the base price, which is the normal washer cycle price.
  • Page 19 Coin Washer Default Cycle (Preset at the Factory) The selected bath LED begins to blink. The display shows the letters “ct” in the left two digits and the bath cycle time in the right two digits. Again the up/down buttons change this value. The range is shown below. The following table shows the complete details for the coin washer default cycle.

  • Page 20: Trouble Shooting

    Notes Section 4: Trouble Shooting Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...

  • Page 21: Common Troubleshooting Solutions

    Common Troubleshooting Solutions Symptom Probable Cause Suggested Remedy Door will Door Rod Check to see that door rod from solenoid to lock ass’y is Symptom Probable Cause Suggested Remedy not open long enough to allow lock ass’y to disengage. If not, adjust rod.

  • Page 22: Troubleshooting Machine Fault Errors

    Troubleshooting Machine Fault Errors Common Troubleshooting Solutions Symptom Probable Cause Suggested Remedy The following are descriptions of fault codes that will appear on the front of the washer. There is a chart format that shows what fault code that will be displayed at washer front. Water does Pressure Switch Check pressure switch continuity between terminals.
  • Page 23 Fault# Description Customer Action Fault# Description Customer Action The variable frequency Check the data communication cable between the Wrong size drive installed Check VFD fault code before turning off power.Check to drive (VFD) and the washer computer and the variable frequency drive ensure all the harnesses are properly connected to the washer computer are not (VFD).
  • Page 24 Fault# Description Customer Action Optional water valve PCB Soft reset control. removed or water valve has The temperature sensor Step 1: Make sure the cooling fins on the VFD heatsink been replaced . inside of the variable and the ventilation louvers on the VFD cooling fan cover frequency drive detects that are clean.
  • Page 25 Variable Frequency Drive Control Notes Digital Readout Faults Fault# Description Customer Action VFD received an illegal Reset drive. command. Possible controller problem Illegal data address, VFD Reset drive. received an address not available to the controller. Illegal data value received Reset drive.

  • Page 26: Machine Service Procedures

    Top Panel Removal Step 1: Remove 4 screws that hold detergent dispenser to top panel. If front soap dish go to step 2 Step 2: Unlock top panel lock. Step 3: Raise top panel, slide to the rear to release from back clips and lift off. Detergent Dispenser Remove top panel to access dispenser.

  • Page 27: Drain Valve

    Door Locking Solenoid Lower Service Panel Removal Remove 2 screws and pull forward to disengage from the locator studs. The door locking solenoid is powered shut with control voltage to lock the door and releases when voltage is removed. It is located in the left front Drain Valve corner of the washer.

  • Page 28: Door Lock Assembly Operation

    Door Lock Assembly Operation Door cam Flat blade screw on check position door switch latching After loading the clothing, the door should be closed and latched. The locking cam on the door contacts the latching switch actuator which closes the latching switch. The specified number of coins should now be added to start the washer.

  • Page 29: Adjusting The Loading Door

    Adjusting the Loading Door Loading Door Disassembly The door can be adjusted by changing the number of shims behind the door hinge and the door lock Step 1: Remove the loading Step 2: While holding down on Step 3: Work all the way around assembly.

  • Page 30: Outer Cabinet Removal

    Outer Cabinet Removal Cylinder 18lb, 25lb, 40lb. Step 1: Remove the top panel as described previously. Removal of Cabinet 18lb, 25lb, 40lb Step 2: Remove lower service panel as described previously. Step 3: Remove front panel as described previously. Step 1: The power supply, water hoses, and drain connection must all be disconnected before proceeding Step 4: Remove masking ring as described previously.
  • Page 31 Water Seals Reassembly of the Cylinder Replacement Step 1: Use the hub of the drive pulley, a stack of 5/8” flat washers and a 3” long 5/8” bolt to pull the cylinder shaft through the bearings. After the 3” bolt a 2” long bolt will be required to finish pulling Step 1: Remove cylinder from washer (see Cylinder (basket) the cylinder shaft through.

  • Page 32: Tub Back, Bearing And Cylinder Assembly

    Tub Back, Bearing, and Cylinder Assembly 18lb., 25lb., 40lb. Bearing Housing, Water Seals, and Tub Back 18lb., 25lb., 40lb. Removal Removal from Basket Shaft Step 1: Remove assembly from washer (see Tub Back, Bearing and Cylinder (basket) Assembly removal). Step 1: Remove the top panel as described previously. Step 2: Remove basket pulley (see Basket Pulley removal above).

  • Page 33: Bolt Torque Chart

    WCVD55 Bolt Torque Chart WCVD18 Bolt Torque Chart Bolt Size Where Used Torque Bolt Size Where Used Torque 1/2-13 x 2 1/2” Front Mounting Clamp Ring Ends 20-30 ft-lb 1/2-13 x 2” Front Mounting Clamp Ring Ends 30-40 ft-lb 3/8-16 x 3” Front Clamp Ring 100 in-lb 1/2-13 x 1 1/4”...
  • Page 34 Notes Notes Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...

  • Page 35: Control Mounting Trough

    Control Mounting Trough Remove top panel to access control trough. (see Removing Top Panel) It sets on the right side of the machine and holds the control PCB’s, transformers,and pressure switch. Main Data Communication Cable Goes between front PCB board and Variable Frequency Drive unit mounted center rear of machine. It has telephone type connectors at each end and is inserted at Controller PCB and the Variable Frequency Drive.

  • Page 36: Pressure Switch

    Pressure Switch The pressure switch sets the water level in the washer. As the water level rises, it compresses the air in Data Communication Cable the pressure switch hose. When the washer reaches the desired water level, the compressed air in the pressure switch hose opens the contacts in the switch, shutting off the water.
  • Page 37 Notes Notes Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 38 Electrical Path Circuit Schematics Start Circuit Power travels into the machine on L1 & L2 & (L3, if 3 phase used). L1 and L2 provide 208- 240VAC to the controls transformer which steps the voltage down to 120VAC for the controls. (The L1 connection at the controls transformer must be checked at start-up to coincide with machine operating voltage) The 120VAC travels out from the transformer on either [X-1 red wire directly to the 1.5 amp fuse] or [X-1 black/red wire to TB-4 and then through the red wire to the 1.5 amp fuse].

  • Page 39: Wash Circuit

    The prewash or wash LED will illuminate at this time, powered through the white wires from the P-3 con- Unlock Thermoactuator and Shake Out Circuit nection of the main control PCB to the LED printed circuit board. Using the factory preset cycle as an example: The washer fills the tub through the back of the machine with either one or both the C1 cold and 70 seconds before the end of the cycle the main control PCB signals the relay PCB to remove 120VAC H1 hot water valves.
  • Page 40 Schematic Wiring Diagram Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 41 Schematic Wiring Diagram Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 42 Schematic Wiring Diagram Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 43 Schematic Wiring Diagram Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 44 Schematic Wiring Diagram Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 45 Schematic Wiring Diagram Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...
  • Page 46 Notes Notes Part # 8533-050-001 2/22 Part # 8533-050-001 2/22...

  • Page 47: V-Series Accessories

    V-Series Accessories Kits, Assemblies, & Common Parts WCVD18KCS-10 120 volt 60hz Single Phase Coin Acceptor Components Part Number WCVD18KCS-12 208-240 volts 60hz Single Phase or Three Phase Mechanical Coin Acceptor 9021-001-010 WCVD25KCS-12 208-240 volts 60hz Single Phase or Three Phase...

  • Page 48: Wiring Harness Part # By Model

    Wiring Assembly Blu/Wht ALL..............1 8220-090-009 Wiring Assembly Blk/Blu ALL..............1 8220-001-231 Wire Assembly Green 7" WCVD-18............1 8220-001-478 Harness Power Terminal Block WCVD-55,WCVD-75.........1 V-Series Vended 9627-747-002 Harness Power Terminal Block WCVD-25, WCVD-40........1 9627-747-003 Harness Power Terminal Block WCVD-18 ..........1 9627-831-001 Part # 8533-050-001 2/22...

  • Page 49: Cabinet And Front Panel Group Part

    Cabinet and Front Panel Group Part # by Model Description .................Qty Part Number 9454-656-001 Panel, Side (Left or Right) - stainless WCVD-25.........2 Panel, Side (Left or Right)-stainless WCVD-55........4 9454-672-001 9454-635-005 Panel, Right Side-stainless WCVD-18..........1 Panel, Left Side - stainless WCVD-18..........1 9454-635-006 9989-449-001 Panel, Side (Left or Right)-stainless WCDV-40........2...
  • Page 50 Cabinet and Front Panel Group Part # by Model Continued Notes Description .................Qty Part Number Handle (bumper guard) WCVD-18.............1 9244-081-001 Handle (bumper guard) WCVD-40, WCVD-25........1 9244-081-002 Handle (bumper guard) WCVD-55,WCVD-75........1 9244-081-003 Screw.....................4 9545-045-010 Screw, Guide...................2 9545-008-023 Screw Mtg., Flat Head..............2 9545-008-014 Washer, Finish.................2 8641-585-001...
  • Page 51 Rear View Access Part # WCVD-18, WCVD-25, WCVD-40 Description....................Qty Part Number Drive Motor, 3 Phase (Inverter duty) WCVD-25,WCVD-40.........1 9376-305-001 Drive Motor, 3 Phase (Inverter duty) WCVD-18..........1 9376-304-001 Rod, Motor Mtg WCVD-18,WCVD-25...............1 9497-222-002 Rod, Motor Mtg WCVD-40 ................1 9497-222-004 Screw (end of motor rod) WCVD-18,WCVD-25,WCVD-40.........1 9545-029-005 Lockwasher (end of motor rod)WCVD-18,WCVD-25,WCVD-40......1 8641-582-014...
  • Page 52 Rear View Access Part # WCVD-55, WCVD-75 Description....................Qty Part Number Hose, Overflow Vent 14” WCVD-75,WCVD-55..........1 9242-449-003 Hose, Overflow to drain WCVD-75, WCVD-55..........1 9242-463-004 Pulley, Driven WCVD-55,WCVD-75..............1 9453-176-005 Bushing, TaperWCVD-55,WCVD-75..............1 9053-078-002 Screw......................3 9545-029-011 Lockwasher....................3 8641-582-003 Drive Belt WCVD-75..................1 9040-079-003 Drive Belt WCVD-55..................1 9040-079-002 Channel, Rear WCVD-75................1 9081-140-001...

  • Page 53: Cylinder, Seals & Bearings Part

    Cylinder, Seals, & Bearings Part # WCVD-18, WCVD-25, WCVD-40 Description....................Qty Part Number Housing, Bearing- Assembly (includes items #2-#6)WCVD-25......1 9803-179-002 Housing, Bearing...................1 9241-169-002 Bearing, Front ( LARGE )................1 9036-159-002 Bearing, Rear ( SMALL )................1 9036-159-001 Spacer, Bearing.....................1 9538-158-001 Ring, Bearing Retainer ( internal type )............1 9487-238-001 Housing, Bearing-Assembly (includes items #2-#6) WCVD-18......1 9803-182-001...
  • Page 54 Cylinder, Seals, & Bearings Part # WCVD-55, WCVD-75 Description....................Qty Part Number Cylinder, Assy WCVD-55.................1 9848-116-001 9848-125-001 Cylinder, Assy WCVD-75.................1 Tub and Cylibnder Assy. WCVD-55..............1 9869-009-001 9869-015-001 Tub and Cyclinder Assy. WCVD-75..............1 Housing&Bearing Assembly WCVD-55,WCVD-75 (includes items #2-#6)...1 9803-187-001 9241-181-004 Housing, Bearing...................1 Bearing, Front....................1 9036-159-006 9036-159-005...
  • Page 55 Door Latching & Lock Group (All Models) Part Number Description....................Qty Lock Assy, Complete (includes #1 thru #22)...........1 9885-023-001 Door Lock & Cam Kit (replaces 9885-023-001)..........1 9732-347-001 Plate Assy, Door Lock..................1 9982-284-001 Washer, Flat....................1 8641-581-030 Actuator, Latching Switch................1 9008-005-001 Pawl, Locking....................1 9450-002-002 Washer, Spring....................1 8641-569-003...
  • Page 56 Loading Door Group by Part # WCVD-18 Description....................Qty Part Number 9960-273-001 Loading Door, Complete (includes 1 thru 10)..........1 Loading Door, Ring..................1 9487-264-001 9206-411-002 Gasket, Loading Door..................1 Window, Loading Door..................1 9635-018-001 9913-134-003 Shaft Assy, Locking (includes 4 thru 7)............1 Shaft, Door Locking..................1 9537-195-002 Cam, Locking....................1 9095-040-001...
  • Page 57 Loading Door Group by Part # WCVD-25, WCVD-40, WCVD-55 Description....................Qty Part Number Loading Door, Complete (includes 1 thru 10)..........1 9960-274-002 Loading Door, Ring..................1 9487-265-001 Gasket, Loading Door..................1 9206-419-001 Window, Loading Door..................1 9635-016-001 Shaft Assy, Locking (includes 4 thru 7)............1 9913-134-003 Shaft, Door Locking..................1 9537-195-002 Cam, Locking....................1...
  • Page 58 Loading Door Group by Part # WCVD-75 (180 Door) Description....................Qty Part Number Loading Door, Complete ( includes #1thru #10) ..........1 9960-274-004 Loading Door Ring 180 degree...............1 9487-265-002 Gasket, Loading Door..................1 9206-419-001 Window, Loading Door..................1 9635-016-001 Shaft Assy. Locking (includes #5 thru #8)............1 9913-134-003 Shaft, Door Locking..................1 9537-195-002...

  • Page 59: Drain Valve Group Part # By Model

    Drain Valve Group by Part # Part Number Description....................Qty Valve, Drain (includes 2-11) (3”) WCVD-25, WCVD-40, WCVD-55, WCVD-75..1 9379-187-001 9064-070-001 Body, Valve (w/ball) WCVD-25, WCVD-40, WCVD-55, WCVD-75.......1 Motor & Gear Train..................1 9914-137-001 9452-538-001 Plate, Motor Mtg...................1 Screw......................3 8639-994-001 9534-339-001 Spring, Drive WCVD-25, WCVD-40, WCVD-55, WCVD-75.........1 Screw......................2 9545-054-001 9545-054-002...
  • Page 60 Chassis and Drain Group by Part # WCVD-55, WCVD-75 Part Number Description 9945-105-002 Base Assy, Frame WCVD-55................1 9945-125-002 Base Assy, Frame WCVD-75................1 9930-138-001 Outer Tub Assy WCVD-55................1 9930-144-001 Outer Tub Assy WCVD-75................1 9950-053-002 Ring Assy, Tub Mtg-Front WCVD-55, WCVD-75..........1 9545-017-013 Screw Hexhead 1/2 x 2 WCVD-75,WCVD-55..........1 8640-417-005 Nut Whizlok WCVD-75................1...
  • Page 61 Chassis and Drain Group by Part # WCVD-18, WCVD-25, WCVD-40 Part Number Description 9945-097-002 Base Assy, Frame WCVD-40................1 9945-093-002 Base Assy,Frame WCVD-18.................1 9945-105-002 Base Assy, Frame WCVD-55................1 9945-087-002 Base Assy,Frame WCVD-25.................1 9930-136-001 Tub Assy WCVD-40,..................1 9930-135-001 Tub Assy WCVD-18..................1 9930-137-001 Tub Assy WCVD-25..................1 9930-138-001 Tub Assy WCVD-55..................1...
  • Page 62 Water Inlet & Rear Channel Group by Part # Water Inlet Breakdown Description....................Qty Part Number 9379-183-003 Valve, Water Inlet (includes 1 thru 6)............2 Screen, Inlet end of valve................2 9555-056-001 9089-017-001 Coil Assy., 120 V....................2 Diaphragm....................2 9118-049-001 9211-021-002 Guide, Solenoid.....................2 Armature......................2 9015-008-001 Spring, Armature...................2 9534-298-001...

  • Page 63: Electrical Components - Top Compartment

    Eletrical Compenents - Top Compartment Part Number Description Trough Assy, Controls (all parts below #2 - #43 & trough)....WCVD-55 9857-154-001 9857-151-001 Trough Assy,Controls(all parts below #2-#43 & trough) .....WCVD-25 Trough Assy,Controls(all parts below #2-#43 & trough) ....WCVD-18-12 9857-150-001 9857-149-001 Trough Assy,Controls(all parts below #2-#43 & trough) ....WCVD-18-10 Trough Assy, Controls (all parts below #2 - #43 &...
  • Page 64 Eletrical Compenents - Top Compartment Continued Notes Part Number Description Harness P5/Pressure WCVD-18..........1 9627-800-001 9627-801-001 Harness P5/Pressure WCVD-25..........1 Harness P5/Pressure WCVD-55,WCVD-75........1 9627-803-001 9627-802-001 Harness P5/Pressure WCVD-40..........1 Transformer, (Step Down) 120/2.3 VAC&24 VAC ALL....1 8711-009-001 9545-008-026 Screw, Transformer Mtg #10Bx1/2"........4 Lockwasher #10 exttooth............4 8641-582-006 8220-001-231 Wire Assembly BLK/Blu............1...
  • Page 65 Control Panel Group by Part # Part Number Description 9989-473-001 Panel Control Assembly(panel only)WCVD-18-10,WCVD-18-12....1 9989-474-001 Panel Control Assembly (panel only) WCVD-25.........1 9989-475-001 Panel Control Assembly (panel only) WCVD-40.........1 9989-476-001 Panel Control Assembly (panel only) WCVD-55,WCVD-75......1 9545-008-026 Screw, Hxwshrhdundct #10Bx 1/2"............4 9467-024-001 Post Locator Top of panel................2 8640-411-003...

  • Page 66: Coin Handling

    Labels and Diagrams Description Part Number Wiring Diagram, WCVD-18-10 9506-001-001 Wiring Diagram, WCVD-25 9506-003-001 Wiring Diagram,WCVD-75 9506-037-001 Wiring Diagram, WCVD-55 9506-009-001 Wiring Diagram, WCVD-40 9506-005-001 Wiring diagram, WCVD-18-12 9506-007-001 Transient Voltage Surge Suppressor lnfomational 8507-330-001 Instructions Spin Direction WCVD-55,WCVD-75 8507-275-001 Instructions Spin Direction WCVD-25, WCVD-40 8507-274-001 Instructions Spin Direction WCVD-18...

  • Page 67: Coin Handling Group

    Coin Handling Group by Part # Part Number Description 9942-029-001 Vault, Assy WCVD-18...................1 9942-030-001 Vault, Assy WCVD-25...................1 9942-030-002 Vault, Assy WCVD-40...................1 9942-030-003 Vault, Assy WCVD-55...................1 9942-030-004 Vault, Assy WCVD-75...................1 9545-008-026 Screw, 10Bx 1/2" Vault Mtg...............2 9545-008-031 Screw, 10AB x 1/2" Vault Mtg..............2 9732-122-001 Kit, Coin Box W/Hardware (includes 3 thru 6)..........1 9349-033-001...

  • Page 68: Maintenance

    Preventative Maintenance Daily Step 1: Check that the loading door remains securely locked and cannot be opened during an entire cycle. Step 2: Clean the top, front, and sides of the cabinet to remove residue. Step 3: Clean the soap dispenser and lid and check that all dispenser mounting screws are in-place and tight.

This manual is also suitable for:

Wcvd18kcs-10Wcvd18kcs-12Wcvd25kcs-12Wcvd40kcs-12Wcvd55kcs-12Wcvd75kcs-12

Table of Contents