Table of Contents
Advertisement
Playback
Playing a song (Play)
When you wish to playback song data on the
sequencer, you must first record song data, or load or
dump song data into the TRITON.
To load song data from a floppy disk etc., use Disk
mode.
1 In Sequencer mode, press P0: Play/REC.
2 Use "Song No. and name" to select the desired
song (
p.64).
3 Press the [START/STOP] key.
The song you selected in step 2 will begin playing.
Pressing the [START/STOP] key in pages other
than Sequencer mode P1: Cue List or P5: Pattern/
RPPR will start song playback. When the [START/
STOP] key is pressed in P1: Cue List, the currently
selected cue list will begin playing. When the
[START/STOP] key is pressed in P5: Pattern/
RPPR, the currently selected pattern will begin
playing.
4 If you press the [START/STOP] key during play-
back, the playback will stop.
Press the [START/STOP] key once again, and play-
back will resume from where it had been stopped.
• Pressing the [LOCATE] key will move to the
specified location.
• Pressing the [PAUSE] key will resume playback.
• Pressing the [<<REW], [FF>>] keys will rewind or
fast-forward. These can be used during playback
or when paused.
The speed of rewind and fast-forward is set by the
"FF/REW Speed" page menu command.
Mute/Solo function
You can use the PLAY/MUTE/REC buttons and SOLO
ON/OFF buttons in the Program Select tab of P0: Play/
REC to hear or mute a desired individual track 1–16.
For example, this can be used when you wish to record
new tracks while listening only to the rhythm section
of the previously recorded tracks.
You can use the page menu command "Solo Selected
Track" to hear only the currently selected tracks. It is
convenient to use this while setting track parameters
or effect settings (
p.47 in the Parameter Guide).
Make sure that page P0: Play/Rec is opened.
1 Press the [START/STOP] key to playback the song.
2 Press the Prog. 1–8 tab.
3 Press the track 1 PLAY/MUTE/REC button once.
The display will change to "MUTE," and the play-
back of track 1 will no longer be heard. In this way,
62
the "mute" function allows you to silence a speci-
fied track.
Press the track 2 PLAY/MUTE/REC button once.
The display will change, and the playback of track 2
will also be muted.
To cancel muting, press the PLAY/MUTE/REC but-
ton once again so that the display changes to PLAY.
Each time you press the button, the display will
alternate between MUTE and PLAY.
4 Next press the track 1 SOLO button once.
The display will change, and now only the track 1
playback will be heard. In this way, the Solo func-
tion lets you hear only a specified track. (If both
Mute and Solo are used, the Solo function will be
given priority.)
Press the track 2 SOLO button once.
The display will change, and only the playback of
tracks 1 and 2 will be heard.
To turn off the Solo function, press the SOLO but-
ton once again. Press the track 1 and 2 SOLO but-
tons once each.
The display will change, and the playback of tracks
1 and 2 will be muted. If the Solo function is turned
off for all tracks, playback will be according to the
PLAY/MUTE/REC button settings.
[LOCATE] settings
These settings are made by the page menu command
"Set Location." You can also set the location during
playback by holding down the [ENTER] key and press-
ing the [LOCATE] key (
Normally you will set this to 001:01.000. You will
return to the beginning of the song.
When you select a song, the [LOCATE] setting will
automatically be set to 001:01.000.
Other playback
In Sequencer mode, you can also use playback func-
tions such as Loop All Tracks, play Patterns (using the
RPPR function), Track Play Loop, and Cue List.
p.48 in the Parameter Guide).
Advertisement
Table of Contents
