Table of Contents
Advertisement
"Send 1", "Send 2": Set the send levels to the master
effects. For this example, set this to 127.
8 Select the IFX1–5 tabs, and set the parameters for
each of the selected effects.
For details on the parameters of each effect (
in the Parameter Guide).
Master effects
The input levels to the master effects are set by the
"Send 1, 2" levels (step 3 or 7). If "Send 1, 2" are zero,
the master effects will not apply. "Send 1" corresponds
to MFX1, and "Send 2" corresponds to MFX2.
9 In Program P9: Edit-Master Effect, select the Mas-
ter FX tab.
0 In MFX1 and MFX2, select the type of each master
effect (
5).
The procedure is the same as when selecting an
insertion effect.
The master effects cannot use double-size effects.
The master effects are mono-in/stereo-out. Even if
a stereo-input effect is selected, it will function as
mono input.
Each time you press the ON/OFF button, the mas-
ter effect will be switched on/off. When OFF, the
output of the master effect will be muted.
A Use "Return 1" and "Return 2" to adjust the output
levels of the master effects.
For each effect, the Wet value of the "Wet/Dry"
parameter is the output level at the effect. The
return value is multiplied with this ("Return" =
127 will be x1.0) to determine the actual output
level of the master effect.
B Select the MFX1 and MFX2 tabs, and set the
parameters for each selected effect.
For details on the parameters of each effect, refer to
p.155 in the Parameter Guide.
Master EQ
C Use the stereo 3-band master EQ to make final
equalizing adjustments immediately before the
sound is output from the AUDIO OUTPUT L/
MONO and R jacks.
Move the slider for each band to make adjustments.
108
You can select the Master EQ tab, and adjust the
band frequency of the master EQ (
Parameter Guide).
p.155
Effect settings in Combination, Song,
and Song Play modes
In Combination, Sequencer, and Song Play modes, you
can specify the routing of each timbre/track to the
insert effects and master effects. These settings are
made in the same way in each of these modes. We will
be using the example of Combination mode in our
explanation here.
Routing
1 In Combination P8: Edit-Insert Effect, select the
Routing tab.
2 Select "IFX/Indiv.Out BUS Select." Here you can
specify the bus (insert effect) to which the output
of each timbre will be sent.
The routing, insert effects, and chain settings are
shown graphically in the upper part of the display
screen. In this example, T01 (timbre 1) uses IFX1
and 2. T02 uses IFX2, T03 uses IFX3 and 4, T02 and
T05 use IFX4, and T06 and T07 use IFX5. Selection
of each effect type, the on/off setting, and chain
settings are made in the Insert Effect tab.
3 Make settings for Send 1 and Send 2.
For each timbre, you can set the send levels to the
master effects.
This can be set only if "IFX/Indiv.Out BUS Select" is
set to L/R or Off.
The actual send level is determined by multiplying
this by the "Send 1" or "Send 2" settings for oscil-
lators 1 and 2 within the program selected by the
timbre. If the program parameter "Send 1" or
"Send 2" is set to 0, the resulting level will still be 0
even if you raise this send level.
If "IFX/Indiv.Out BUS Select" is set to IFX1–5, the
send levels to the master effects are set by "Send 1"
and "Send 2" (Insert FX tab) following the insert
effects.
Insert effects
Select an effect for IFX1–IFX5, and set "Pan," "BUS Sel.
(BUS Select)," "Send 1" and "Send 2" for the signal that
p.207 in the
Advertisement
Table of Contents
