Song Restore; Initialize/Format - Korg D8 Owner's Manual

^ ^ ^ ^ Song restore

This will be displayed if you select Restore in P4-1.
This operation restores (recalls) the song that was
backed up.
You can select either a removable disk (or disks) or a
DAT (multiple volumes are not supported).
If a backup of all songs was performed to a removable
disk, you can choose whether to restore all songs or
only a specified song.
If a backup of all songs was performed to DAT, it is
only possible to restore all songs.
Be aware that when you perform a Restore of all songs,
the data will be written to the restore destination drive,
and all data that was previously in the restore destina-
tion drive will be lost.
Restore œ
15 16
A01:SngN ø
P5-12 Source drive/DAT select............................. [A...G, H]
Selects the restore source: a removable disk drive or
DAT.
Since Restore can be done only from a RM (removable
disk) or DAT, this operation cannot be executed when
a hard disk is selected.
A: SCSI ID 0, B: SCSI ID 1, C: SCSI ID 2, D: SCSI ID 3,
E: SCSI ID 4, F: SCSI ID 5, G: SCSI ID 6, H: DAT
P5-13 Source drive/DAT type display............... (RM, DAT)
P5-14 Source drive capacity display...........................
(disk capacity/no display)
When P5-13 is RM this will indicate the formatted
capacity (bytes). For DAT, nothing will be displayed.
P5-15 Source song number select ................... [01...50, All]
Selects the song(s) which will be restored from the
source drive or DAT.
When 01...50 is selected, the selected song will be
restored.
When All is selected, all songs will be restored.
If only one song was backed up, only 01 can be
selected.
When restoring an "all song" backup from DAT, All is
the only valid selection. If you select an individual
song number, your selection will be ignored.
P5-16 Source song name display (four characters displayed)
P5-17 Destination drive select .....................................[I...G]
Selects the restore destination drive.
I: Internal IDE (internal drive), A: SCSI ID 0, B: SCSI ID
1, C: SCSI ID 2, D: SCSI ID 3, E: SCSI ID 4, F: SCSI ID 5,
G: SCSI ID 6
50
12 13 14
A:RM 100 ø
17 18 19
øB02:NoDA
P5-18 Destination song number select ................. [01...50]
When restoring an individual song (i.e., if 01...50 was
selected in P5-15), you can select the song number into
which the data will be restored.
The data will be restored into the number that you
specify, and songs following this restore destination
number will be renumbered upward.
P5-19 Destination song name display ........................
(four characters displayed)
This will be displayed only when restoring an individ-
ual song (i.e., if 01...50 was selected in P5-15).
20 21
øB:HD1300œ
P5-20 Destination drive type display.................. (HD, RM)
The formatted capacity (bytes) of the disk will be dis-
played only when performing an "all song restore"
(All is selected in P5-19).
HD: Hard Disk, RM: Removable Disk
P5-21 Destination drive capacity display .. (disk capacity)

^ ^ ^ ^ Initialize/format

Initial œ
This will be displayed if you select Initial or Format in
P5-1.
Perform this operation for a newly-purchased drive.
You must perform this operation on a drive which was
previously used by another device before that drive
can be used with the D8, or on a drive which fre-
quently produces Disk Error indications during play-
back, etc.
P5-22 Destination drive select................................ [I, A...G]
Selects the drive that you wish to initialize or format.
I: Internal IDE (internal drive), A: SCSI ID 0, B: SCSI ID
1, C: SCSI ID 2, D: SCSI ID 3, E: SCSI ID 4, F: SCSI ID 5,
G: SCSI ID 6
P5-23 Destination drive type display.................. (HD, RM)
This indicates the type of drive.
HD: Hard Disk, RM: Removable Disk
22 23
A:RM 100 œ