Program Playback Of Songs; Switching Scenes During Playback; Step5 Moving And Storing Time Locations; Moving The Current Time - Korg D8 Owner's Manual

5. Program playback of
songs
You can enable two or more songs to playback in a
specified order. This can be used to playback a
medley of songs, or when you wish to record con-
secutive mixdowns of songs to DAT or MD. Pro-
gram Play can be performed even across multiple
drives. As an example, we will explain how to
playback songs in the order of song number I
(internal drive) 01 I02
1
Press the [EDIT] key, and then press the [PLAY
MODE] key several times to access the "P
play ( is the sequence of playback).
P01:I01 œ
2
Rotate the [VALUE] dial to select the first step in
the playback sequence; P01.
3
Press the [ ] key, and then rotate the [VALUE]
dial to select the drive from which the song will be
played back. In this example, select the internal
drive I.
4
Press the [ ] key, and then rotate the [VALUE]
dial to select the song which will be played back as
the first song. In this example, select 01.
5
Press and hold the [
second to finalize the first song for playback. When
this is finalized, the "?" will disappear.
6
Rotate the [VALUE] dial to select the second song
for playback. Referring to steps 3–5, set P02 to
song I02, and set P03 to song A05.
7
Press the [PLAY] key, and the songs will playback
in the specified sequence, starting with I01.
Program playback is available only when you are
in this page. Also, the specified sequence of songs
will be canceled when you leave this page.
6. Switching scenes dur-
ing playback
A set of mixer settings that have been stored is
called a "scene", and scenes can be switched as
time elapses during playback. (Refer to p.29)
24
A (SCSI ID 0) 05.
" dis-
PLAY
EDIT
MODE
E E
] key for approximately 1
Moving and storing
time locations
STEP5
This section explains how to move
between time locations in a song. It also
explains how you can store a specific time location for
instant recall.

1. Moving the current time

Using the location counter to move
1
Simultaneously press the [
move the cursor below the location counter.
01:KORG1 œ
2
Use the [ ] or [ ] keys to move the cursor to the
unit of time that you wish to change (measure
B
beat , 1/96th beat, Mark etc.)*. For details on
Marks, refer to p.26.
3
Rotate the dial to move the time location.
Rotating the dial toward the right will increase the
time, and rotating it toward the left will decrease
the time.
* You can change the units of time that appear in the
display. Four methods of display can be selected.
(Refer to "5. DISPLAY MODE", p.51)
Using the [STOP], [REW] and [FF] keys to
move
Moving backward
Press the [REW] key to move toward the beginning
of the song. If you hold down the key, you will
move continuously. You can also move during
playback.
Moving forward
Press the [FF] key to move toward the end of the
song. If you hold down the key, you will move con-
tinuously. You can also move during playback.
Moving to the beginning of the song/Moving to the
beginning of the previous song
If the current time is in the middle of the song, you
can hold down the [STOP] key and press the
[REW] key to move to the beginning of the song.
If the current time is at the beginning of the song,
you can hold down the [STOP] key and press the
[REW] key to select the song of the previous num-
ber, and move to its beginning.
Moving to the beginning of the next song/Creating a new song
If you hold down the [STOP] key and press the
[FF] key, you will select the song of the following
number, and move to its beginning. If the follow-
ing number does not contain a song, a new song
will be created for that number. (Refer to p.10)
] and [ ] keys to
NO YES
M
,