Edit Play Mode; Trigger; P1 Pre Roll Time Setting; P2 Post Roll Time Setting - Korg D8 Owner's Manual

8. EDIT PLAY MODE

P1 Pre roll time setting
Here you can specify the pre roll time that is added to
the IN time of Auto Play On
when Auto Punch In/Out is performed.
When Auto Play On or Auto Repeat On is used in con-
junction with Auto Punch In/Out, you will be able to
listen for the pre roll time before punch in occurs,
allowing you to prepare to start recording.
1
PreRol:02M
P1-1 Pre roll time numerical setting .................. [00...10]
P1-2 Pre roll time unit select..................................... [M, s]
Specifies the pre roll time in either measures or sec-
onds.
In P1-1 you can specify a numerical value (00–10), and
in P1-2 you can select either M (measure) or s (second)
units. When you change the pre roll time unit, the post
roll time unit will change automatically. When M is
selected, the maximum pre roll time is 10 measures.
When s is selected, the maximum is 10 seconds.
When the power is turned on, the pre roll time and
post roll time are automatically set to 02M.
P2
Post roll time setting
Here you can specify the post roll time that will be
added to the OUT time for Auto Play On
Repeat On when Auto Punch In/Out is performed.
When Auto Play On or Auto Repeat On is used in con-
junction with Auto Punch In/Out, you will be able to
listen for the post roll time after punch out occurs,
allowing you to verify the connection following the
recording.
1
PstRol:00M
P2-1 Post roll time numerical setting...................[00...10]
P2-2 Post roll time unit select ................................... [M, s]
Specifies the post roll time in either measures or sec-
onds.
In P2-1 you can specify a numerical value (00–10), and
in P2-2 you can select either M (measure) or s (second)
units. When you change the post roll time unit, the pre
roll time unit will change automatically. When M is
selected, the maximum post roll time is 10 measures.
When s is selected, the maximum is 10 seconds.
52
and Auto Repeat On
2
and Auto
2
When the power is turned on, the pre roll time and
post roll time are automatically set to 02M.
Pre roll point
IN
Pre roll time
P3
Program play
Up to 50 songs can be played back in a specified order.
Program Play will function only while you are in this
page.
When the audio data of each song reaches silence,
playback will proceed to the next song.
1 2 3
P01:I-- œ
P3-1 Program playback order select................. [01...50]
Selects the order (step) of program song playback. The
specified song will playback for each step, from low to
high numbered steps. Steps for which no song is speci-
fied in P3-3 or steps for which the drive specified in P3-
2 and P3-3 was not found will be skipped.
P3-2 Playback drive select.................................... [I, A...G]
I: Internal IDE (internal drive), A: SCSI ID 0, B: SCSI ID
1, C: SCSI ID 2, D: SCSI ID 3, E: SCSI ID 4, F: SCSI ID 5,
G: SCSI ID 6
P3-3 Playback song number select .................... [01...50]
Selects the drive and song number that will playback.
When you exit this page, the selected order of songs
will be reset.
The location counter display is different only during
Program Play. (Refer to "5. Display MODE", p.51)

9. TRIGGER

This function allows the beginning of recording to be
triggered by the input signal.
Trigger recording on/off
On (indicator lit): When in record ready mode, an
input signal that exceeds the threshold level (refer to
EDIT TRIGGER P1) will initiate recording.
Off (indicator off): Recording will begin normally.
Be aware that when this is On, recording will not begin
until the threshold level is exceeded. Press the [STOP]
key to cancel trigger recording, and readjust the
threshold level.
Post roll point
OUT
Post roll time
............................................ [On, Off]