Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maxtang BYT-35
Summary of Contents for Maxtang BYT-35
- Page 1 BYT-35 Disk Size SBC Motherboard...
- Page 2 Copyright © 2021 Shenzhen Maxtang Computer Co., Ltd. All rights reserved. No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Shenzhen Maxtang Computer Co., Ltd (hereinafter referred to as “Maxtang”).
- Page 3 Shenzhen Maxtang Computer Co., Ltd BYT35 Motherboard User Manual (Version 1.5) Version: Description Issue Date: Initial Version 2018/04/27 V1.0 Updated the power to 12V/19V DC-in 2021/10/28 V1.5...
-
Page 4: Table Of Contents
Shenzhen Maxtang Computer Co., Ltd Contents Chapter 1 Product Introduction ......................3 1.1 Brief Introduction ........................3 1.2 Parameters ..........................3 Chapter 2 Hardware ................4 2.1 Connector Diagram ........................4 2.2 Jumper Setting ........................5 2.3 Memory Slots .........................5 2.4 Display Interfaces ........................5 2.5 Storage (Screen Printing: MSATA, SATA1, PWSATA) .............7 2.6 USB Interface .........................7... -
Page 5: Chapter 1 Product Introduction
Shenzhen Maxtang Computer Co., Ltd Chapter 1 Product Introduction 1.1 Brief Introduction The BYT-35 V1.5 motherboard is a 3.5" SBC (Single Board Computer) based on the Intel Bay Trail platform, features small form factor, low power consumption and high performance. 1.2 Parameters Bay Trail Platform: ⚫... -
Page 6: Chapter 2 Hardware
Shenzhen Maxtang Computer Co., Ltd Chapter 2 Hardware 2.1 Connector Diagram... -
Page 7: Jumper Setting
Shenzhen Maxtang Computer Co., Ltd 2.2 Jumper Setting Please configure the jumpers according to your requirements before installing the hardware. How to identify the first header of jumpers and pins: Observe the mark beside the jumper or pins and find the header marked by “1”... - Page 8 Shenzhen Maxtang Computer Co., Ltd LVDS Backlight Pin (eDP/LVDS_ADJ): Signal LCD_BKL_ADJ LCD_BKL_ON LVDS Operating Voltage Pin (J3): Interface Setting Function Close VCC(+3.3V) Close VCC(+5V) Close VCC(+12V) Note: LVDS screen’s power can be adjusted among 12V/5V/3.3V via jumper setting. Customers can connect voltage with jumper cap according to their LVDS screen’s voltage (Connecting different voltages via jumper...
-
Page 9: Storage (Screen Printing: Msata, Sata1, Pwsata)
Shenzhen Maxtang Computer Co., Ltd LCD_BKL_ADJ LCD_BKL_ON EDP Operating Voltage Pin (Screen Printing: J3) Interface Setting Function Close VCC(+3.3V) Close VCC(+5V) Close VCC(+12V) Note: The eDP screen’s power can be flexibly adjusted between 12V/5V/3.3V via jumper setting. It is strictly forbidden to short-circuit pins of different voltages at the same time. -
Page 10: Lan
Shenzhen Maxtang Computer Co., Ltd 2.6 LAN The board is equipped with two Intel i211 Gigabit Network Controller, RJ45 interface, supports Magic packet wake-up and PXE network boot. LED Status Indicators: LI_LED Status (Orange) Function ACT_LED Status (Green) Function Always on... -
Page 11: Gpio (Screen Printing: Gpio)
Shenzhen Maxtang Computer Co., Ltd DSR# RTS# CTS# VCC(same as board input） ） DCD# DTR# DSR# RTS# CTS# VCC(same as board input） ） RS485 (Screen: COM5_6) Signal Signal COM5_DATA- COM6_DATA- COM5_DATA+ COM6_DATA+ 2.10 GPIO (Screen Printing: GPIO) The board provides a set of 2x5Pin GPIO (2.0mm spacing), 8 lanes of programmable I/O in total. -
Page 12: Switch Button/ Indicator Pin (Screen Printing: Jpower)
Shenzhen Maxtang Computer Co., Ltd PWR2 (Screen Printing：PWR2) Definition Definition 2.13 Switch Button/ Indicator Pin (Screen Printing: JPOWER) The board has a set of 2.0mm spacing pins that can be connected to a switch button, a system reset button, a hard disk read/write indicator, a power-on indicator.
Need help?
Do you have a question about the BYT-35 and is the answer not in the manual?
Questions and answers