Shenzhen Maxtang Computer Co., Ltd Chapter 1 Product Introduction 1.1 Brief Introduction The MTN-FP750 compact mini pc is a 4x4 small form factor pc based on AMD Ryzen 6000/7000 series processor, built with innovative technology and optimized high performance. 1.2 Parameters AMD Ryzen Mobile Processors Processor: ⚫...
Chapter 2 Hardware 2.1 Installations Please refer to the following steps for installations: Read the user manual carefully to make sure all the adjustments on the FP750 are correct. Installing the Memory: ⚫ Press the ejector tab of the memory slot outwards with your fingertips.
Shenzhen Maxtang Computer Co., Ltd 2.10 USB Interfaces The board provides 3x USB3.2 Gen 2 interfaces, and 1x USB2.0 interface. 2.11 Type-C Interface The board features a Type-C(USB-C) Full-functioned interface, the interface also supports USB3.2 Gen 1 upstream/Display Port 1.4 Alt Mode functions.
Shenzhen Maxtang Computer Co., Ltd Chapter 3 BIOS Setup 3.1 Entering the BIOS Turn on the computer and press <Delete> entering the BIOS After the computer is turned on, keep pressing F11, select enter Setup BIOS Hotkeys: F9: Restore to Factory setting.
Shenzhen Maxtang Computer Co., Ltd 3.3 Advanced Settings Select any of the items in the left frame of the screen. The advanced sections allow you to configure, improve and set up system features according to the preference of the CPU Configuration. All Advanced BIOS Setup...
Shenzhen Maxtang Computer Co., Ltd 3.3.1 AMD fTPM Configuration AMD fTPM Switch: The TPM (Trusted Plat-form Module) is a secure key generator and key cache management component that enables protected storage of encryption keys and authentication credentials for enhanced security.
Shenzhen Maxtang Computer Co., Ltd 3.3.3 Hardware Monitor PC Health Status The PC health status displays CPU temperature, system temperature, fan speed, and other relevant voltage values. The above parameters have a certain range, and the system cannot run beyond these ranges.
Shenzhen Maxtang Computer Co., Ltd 3.3.4 Watchdog Configuration Watchdog Configuration WDT Timeout Mode select: Minute or Second 3.3.5 S5 RTC Wake Settings Wake system From S5: timing boot settings, disabled by default. Fixed Time: Select Fixed Time and the system will wake on the Hr: Min: Sec specified.
Shenzhen Maxtang Computer Co., Ltd 3.3.6 SATA Configuration The capacity and model of the hard disk will be displayed under the option after the SATA protocol hard disk has been installed.
Shenzhen Maxtang Computer Co., Ltd 3.3.7 USB Configuration Legacy USB Support Enable Legacy USB support. Disables legacy support if no USB devices are connected. Select enable will keep USB devices available under UEFI’s support. XHCI Hand-off Whether to enable the USB XCHI transfer protocol. A workaround for OS without XHCI hand-off support.
Shenzhen Maxtang Computer Co., Ltd 3.3.9 NVME Configuration The capacity and model of the SSD will be displayed under the option after the NVMe protocol SSD has been installed.
Shenzhen Maxtang Computer Co., Ltd 3.3.10 AMD CBS AMD CBS: Custom BIOS Settings CPU Common Options DF Common Options UMC Common Options NBIO Common Options FCH Common Options SMU Common Options SOC Miscellaneous Control...
Shenzhen Maxtang Computer Co., Ltd 3.3.10.1 SMU Common Options System configuration Sustained Power Limit PPT Control Fast PPT Limit Slow PPT Limit Slow PPT Time Constant STAPM Control Thermal Control Tjmax 10. TDC Control 11. EDC Control 12. PSI3 Control 13.
Shenzhen Maxtang Computer Co., Ltd 3.3.10.2 FCH Common Options SATA Configuration Option Option to check whether the SATA hard drive is recognized AC Power Loss Options "AC Power Loss Options" is a setting that determines the behavior of a computer when power is lost and then restored.
Shenzhen Maxtang Computer Co., Ltd 3.4 Chipset South Bridge Allows users to configure the South Bridge settings. CFX configuration Allows users to view details of the display items. North Bridge Allows users to configure the North Bridge settings.
Shenzhen Maxtang Computer Co., Ltd 3.5 Security Administrator Password: Set the Administrator Password. User Password: Set User Password. Secure Boot: Secure boot...
Page 27
Shenzhen Maxtang Computer Co., Ltd 3.6 BOOT Setup Prompt Timeout: Number of seconds that the firmware will wait before initiating the original default boot selection. A value of 0 indicates that the default boot selection is to be initiated immediately on boot. A value of 65535(0xFFFF) indicates that firmware will wait for user input before booting.
Page 28
Shenzhen Maxtang Computer Co., Ltd 3.7 Save & Exit Save Changes and Exit: Exit the system setup after saving the changes and continue to start the computer. Discard Changes and Exit: Exit the system setup without saving any changes and continue to start the computer.
Need help?
Do you have a question about the FP750 and is the answer not in the manual?
Questions and answers