Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maxtang ALN-10
Summary of Contents for Maxtang ALN-10
- Page 1 ALN-10 Mini ITX Motherboard...
- Page 2 Copyright © 2023 Shenzhen Maxtang Computer Co., Ltd. All rights reserved. No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Shenzhen Maxtang Computer Co., Ltd (hereinafter referred to as “Maxtang”).
-
Page 3: Aln10 Motherboard
Shenzhen Maxtang Computer Co., Ltd ALN10 Motherboard User Manual (Version 0.5) Version: Description Issue Date: V0.5 Initial Version (CN) 2023/03/03 V0.5 Initial Version (EN) 2023/04/23... -
Page 4: Table Of Contents
Shenzhen Maxtang Computer Co., Ltd Contents ALN10 Motherboard ..................1 User Manual ....................1 (Version 0.5) ....................1 Chapter 1 Product Introduction ........................ 4 1.1 Brief Introduction ........................4 1.2 Parameters ..........................4 1.3 Connector Diagram........................5 Chapter 2 Hardware ..................6 2.1 Installations .......................... - Page 5 Shenzhen Maxtang Computer Co., Ltd 3.3.8 Watch Dog Configuration ....................... 23 3.3.9 S5 RTC Wake Settings ......................23 3.3.10 USB Configuration ........................ 24 3.3.11 Network Stack Configuration ....................25 3.3.12 NVME Configuration ......................25 3.4 Chipset .............................. 26 3.4.1 State After G3 ......................... 27 3.5 Security ............................
-
Page 6: Chapter 1 Product Introduction
Shenzhen Maxtang Computer Co., Ltd Chapter 1 Product Introduction 1.1 Brief Introduction The ALN-10 is a mini ITX motherboard based on the Intel Alder Lake-N series processor; features a small form factor, low power consumption, and high performance. 1.2 Parameters CPU: ⚫... -
Page 7: Connector Diagram
Shenzhen Maxtang Computer Co., Ltd 1.3 Connector Diagram DP/HDMI HDMI 2*USB2.0 2*USB3.2 LAN23 LAN1 LINE_OUT MIC_IN DC_IN FP-AUDIO PWR2 GPIO JAUD CPUFAN1 PWSATA SO-DIMM CPUFAN2 PCIEX4 SATA COM2 COM1 M.2-S M.2-E COM3-P SYSFAN COM5-P 1*USB2.0 LADJ/DIS COM36 LBKL 2*USB2.0 2*USB2.0... -
Page 8: Chapter 2 Hardware
Shenzhen Maxtang Computer Co., Ltd Chapter 2 Hardware 2.1 Installations Please refer to the following steps for installations: Read the user manual carefully to make sure all the adjustments on the ALN10 are correct. Installing the Memory: ⚫ Press the ejector tab of the memory slot outwards with your fingertips. - Page 9 Shenzhen Maxtang Computer Co., Ltd multiple displays. 2.4.1 LVDS The board is equipped with a dual-channel 24-bit LVDS interface. LVDS screen power is controlled via LVCC jumpers, LBKL is the LVDS backlight power control, and LADJ/DIS is the backlight polarity control (standard/reverse control) and LVDS switch pins.
- Page 10 Shenzhen Maxtang Computer Co., Ltd same as the DC power supply) Backlight Polarity Adjustment Jumper Settings (Screen Printing: LADJ/DIS) Interface Setting Function Close LVDS OFF Close LVDS ON Close REV (Backlight Control Reverse) Close STD (Backlight Control Standard) 2.4.2 EDP (Optional) As an optional feature, it supports a 2-lane eDP (1.3) interface.
-
Page 11: Storage
Shenzhen Maxtang Computer Co., Ltd 12V/19V (The output voltage is the same as the DC power supply) eDP Screen Power Supply (Screen Printing: LVCC) Interface Setting Function Close VCC 3.3V Close VCC 5V VCC 12V/19V Close (The output voltage is the same... -
Page 12: Lan
Shenzhen Maxtang Computer Co., Ltd 2.8 LAN The board features 2xRJ45 interfaces with Intel high-speed Gigabit network controllers. Two Intel i226-V data rate per port: 2.5Gbps, the MAC address only can be used once and cannot be changed after used. -
Page 13: Lpt
Shenzhen Maxtang Computer Co., Ltd DTR# DSR# RTS# CTS# (NC) COM3-P, COM5-P: Interface Setting Function Close Close Close COM2 as RS485 Signal RS232 RS485 DCD# DATA- DATA+ (NC) DTR# (NC) DSR# (NC) RTS# (NC) CTS# (NC) (NC) 2.10 LPT The board features a 2X13PIN parallel interface that requires an adapter cable to convert it to a standard parallel interface before use. -
Page 14: Gpio (Screen Printing: Gpio)
Shenzhen Maxtang Computer Co., Ltd SLCT (NC) Setting Function Close VCC 3.3V Close VCC 5V 2.11 GPIO (Screen Printing: GPIO) The board provides a set of 2x5Pin GPIO (2.0mm spacing) 8 programmable I/O lanes in total. GPIO: Signal Signal GPP_F11 3.3V... -
Page 15: Audio (Screen Printing: Fp_Audio, Jaud)
Shenzhen Maxtang Computer Co., Ltd (NC) 2.14 Audio (Screen Printing: FP_AUDIO, JAUD) The board is equipped with the advanced ALC897 audio control chip, which ensures high-quality sound output. The green interface functions as the audio output (LINE_OUT), while the pink interface serves as the microphone input (MIC_IN). -
Page 16: Cmos Clearance/Retention
Shenzhen Maxtang Computer Co., Ltd SYSFAN: Signal CPU/System Fan Power Supply Voltage Setting Pins (Screen Printing: JVCCFAN) Interface CPUFAN SYSFAN 2.16 CMOS Clearance/Retention CMOS is powered by onboard button batteries. Clearing CMOS will permanently remove the previous system settings and restore the board system to original settings (factory settings). -
Page 17: Chapter 3 Bios Setup
Shenzhen Maxtang Computer Co., Ltd Chapter 3 BIOS Setup 3.1 Entering the BIOS Turn on the computer and press <Delete> entering the BIOS After the computer is turned on, keep pressing F11, select enter Setup BIOS Hotkeys: F9: Restore to Factory setting. -
Page 18: Advanced Settings
Shenzhen Maxtang Computer Co., Ltd 3.3 Advanced Settings Select any of the items in the left frame of the screen. The advanced sections allow you to configure, improve and set up system features according to the preference of the CPU Configuration. All Advanced BIOS Setup options are described as follows. -
Page 19: Cpu-Power Management Control
Shenzhen Maxtang Computer Co., Ltd 3.3.2 CPU-Power Management Control Intel® Speedstep®(TM): Enhanced Intel SpeedStep® Technology enables the operating system to control multiple frequencies and voltage points for optimal performance and power efficiency. Intel® Speed Shift Technology: An energy-efficient frequency control method by the hardware rather than relying on OS control. -
Page 20: Gt-Power Management Control
Shenzhen Maxtang Computer Co., Ltd 3.3.3 GT-Power Management Control RC6(Render Standby): (Standby) Enable/Disable integrated graphics card standby, default enable. Maximum GT frequency: Maximum GT Frequency, Default max frequency. Disable Turbo GT frequency: Disable Turbo GT Frequency mode, Default disabled. -
Page 21: Thermal Configuration
Shenzhen Maxtang Computer Co., Ltd 3.3.4 Thermal Configuration Enable All Thermal Functions CPU Thermal Configuration: Unlocks the temperature setting, the “Tcc Activation Offset” is the temperature adjustment option, the highest temperature is 105°C. Change the temperature by minus the number of degrees you wish to change. -
Page 22: Acpi Settings
Shenzhen Maxtang Computer Co., Ltd 3.3.5 ACPI Settings Enable ACPI Auto Configuration: Enable ACPI Auto Configuration, Disabled by default. Enable Hibernation ACPI Sleep State: Set the ACPI function power saving mode according to the operating system. Set different hibernation functions. -
Page 23: Super Io Configuration
Shenzhen Maxtang Computer Co., Ltd 3.3.6 Super IO Configuration Serial Port 1~6 Configuration Serial Port: Enable or disable serial port (COM). Device Setting (Read-only): Displays serial ports’ interrupt and location. Change Setting: Change serial port settings and suggest setting “Auto” as default. -
Page 24: Hardware Monitor
Shenzhen Maxtang Computer Co., Ltd 3.3.7 Hardware Monitor PC Health Status The PC health status displays CPU temperature, system temperature, fan speed, and other relevant voltage values. The above parameters have a certain range, and the system cannot run beyond these ranges. -
Page 25: Watch Dog Configuration
Shenzhen Maxtang Computer Co., Ltd 3.3.8 Watch Dog Configuration Watch Dog Configuration WDT Timeout Mode select: Minute or Second 3.3.9 S5 RTC Wake Settings Wake system From S5: timing boot settings, disabled by default. Fixed Time: Select Fixed Time and the system will wake on the Hr: Min: Sec specified. -
Page 26: Usb Configuration
Shenzhen Maxtang Computer Co., Ltd 3.3.10 USB Configuration Legacy USB Support Enable Legacy USB support. Disables legacy support if no USB devices are connected. Select enable will keep USB devices available under UEFI’s support. XHCI Hand-off A workaround for OS without XHCI hand-off support. The XHCI ownership change should be claimed by the USB XCHI driver. -
Page 27: Network Stack Configuration
Shenzhen Maxtang Computer Co., Ltd 3.3.11 Network Stack Configuration Network Stack PXE Network boot setting, disabled by default. 3.3.12 NVME Configuration The capacity and model of the SSD will be displayed under the option after the NVMe protocol SSD has been... -
Page 28: Chipset
Shenzhen Maxtang Computer Co., Ltd 3.4 Chipset Select the chipset tab from the setup screen to enter the chipset BIOS Setup screen. System Agent (SA) Configuration: Northbridge configuration options, including video memory, display devices, and other options. PCH-IO Configuration: Southbridge configuration options, including hard disk, sound card equipment, and... -
Page 29: State After G3
Shenzhen Maxtang Computer Co., Ltd 3.4.1 State After G3 State After G3: State After G3 is set to S0 State (auto-start after connected to power), set to S5 State by default (Turned off after power is connected). -
Page 30: Security
Shenzhen Maxtang Computer Co., Ltd 3.5 Security Administrator Password: Set the Administrator Password. User Password: Set User Password. Secure Boot: Secure boot... -
Page 31: Boot
Shenzhen Maxtang Computer Co., Ltd 3.6 BOOT Setup Prompt Timeout: Number of seconds that the firmware will wait before initiating the original default boot selection. A value of 0 indicates that the default boot selection is to be initiated immediately on boot. A value of 65535(0xFFFF) indicates that firmware will wait for user input before booting. -
Page 32: Save & Exit
Shenzhen Maxtang Computer Co., Ltd 3.7 Save & Exit Save Changes and Exit: Exit the system setup after saving the changes and continue to start the computer. Discard Changes and Exit: Exit the system setup without saving any changes and continue to start the computer.
Need help?
Do you have a question about the ALN-10 and is the answer not in the manual?
Questions and answers