Shenzhen Maxtang Computer Co., Ltd Chapter 1 Product Introduction 1.1 Brief Introduction The ALD-76 is a standard ATX motherboard based on the Intel Alder Lake-S/Raptor Lake-S processor (FCLGA1700 socket) with Z690 chipset. 1.2 Parameters CPU: PCH Z690 + Intel Alder Lake-S/Raptor Lake-S Series Processor Memory: 4x UDIMM DDR5 slots, single slot maximum capacity: 32GB, maximum memory capacity in total: 128GB.
Chapter 2 Hardware 2.1 Installations Please refer to the following steps for installations: Read the user manual carefully to make sure all the adjustments on the ALD76 are correct. Installing the Memory: ⚫ Press the ejector tab of the memory slot outwards with your fingertips.
Shenzhen Maxtang Computer Co., Ltd 2.4 Display Interfaces The board provides 4x HDMI1.4, 1xVGA onboard pin for display interfaces. All HDMI1.4 interfaces supports dummy load. 2.5 Storage (Screen Printing: SATA1-2, SATA3-4, SATA5-6, SATA7-8, M.2-N) The board provides 1 x M.2_Key M type 2280 for NVMe SSD (PCIE4.0 4X Signal), 8 x SATA3.0 standard interfaces, and supports two 1*4PIN SATA hard disk power supply interfaces (2.0mm spacing).
Shenzhen Maxtang Computer Co., Ltd FRO-R MIC2-JD F-IO-SEN(AGND) (NULL) FRO-L LIN2-JD 2.8 COM (Screen Printing: JCOM1, COM25) The board provides five standard RS232 serial ports (COM1 2.54mm spacing, COM2_5 2.0mm spacing), and the COM1 can set as RS232/RS485/RS422 through jumper.
Shenzhen Maxtang Computer Co., Ltd System Fan Definition (screen printing: SYS-FAN1, SYS-FAN2, SYS-FAN3, SYS-FAN4) Signal 2.11 ATX Power Supply (Screen printing: ATX1, ATX2, ATX3) The board power supply: ATX power supply (ATX_24PIN+2*8PIN). ATX_24PIN DEFINTION (screen printing: ATX1) Signal Signal +3.3V +3.3V...
Shenzhen Maxtang Computer Co., Ltd +12V 2.12 LAN (Screen printing: LAN1, LAN2, LAN_LED) The board features four high-speed ethernet controllers, which include 1x Intel i219 (Date Rate Per Port: 1.0 Gbps) plus 3x Intel i210 (Data Rate Per Port: 1.0 Gbps).
Page 14
Shenzhen Maxtang Computer Co., Ltd Start the computer and press the <Del> key to enter the BIOS. Load optimized default values, save the settings, and exit. CMOS (Screen Printing: JCMOS) Setting Function Close Clear CMOS Close Do not clear the CMOS while the computer is powered on to prevent potential damage to the board.
Shenzhen Maxtang Computer Co., Ltd Chapter 3 BIOS Setup 3.1 Entering the BIOS Turn on the computer and press <Delete> entering the BIOS After the computer is turned on, keep pressing F11, select enter Setup BIOS Hotkeys: F9: Restore to Factory setting.
Shenzhen Maxtang Computer Co., Ltd 3.3 Advanced Settings Select any of the items in the left frame of the screen. The advanced sections allow you to configure, improve and set up system features according to the preference of the CPU Configuration. All Advanced BIOS Setup options are described as follows.
Shenzhen Maxtang Computer Co., Ltd 3.3.2 CPU-Power Management Control 1) Intel® Speedstep®(TM): Enhanced Intel SpeedStep® Technology enables the operating system to control multiple frequencies and voltage points for optimal performance and power efficiency. 2) Intel® Speed Shift Technology: An energy-efficient frequency control method by the hardware rather than relying on OS control.
Shenzhen Maxtang Computer Co., Ltd 3.3.3 GT-Power Management Control RC6(Render Standby): Allow/Prohibit integrated graphics card standby, the setting item has been Enabled/Prohibited, and the default setting is (Enabled). Maximum GT frequency: Maximum GT Frequency, Default max frequency. Disable Turbo GT frequency:...
Shenzhen Maxtang Computer Co., Ltd 3.3.4 Thermal Configuration Enable All Thermal Functions CPU Thermal Configuration: Unlocks the temperature setting, the “Tcc Activation Offset” is the temperature adjustment option, the highest temperature is 105°C. Change the temperature by minus the number of degrees you wish to change.
Shenzhen Maxtang Computer Co., Ltd 3.3.7 Super IO Configuration Serial Port 1~5 Configuration Serial Port: Enable or disable serial port (COM). Device Setting (Read-only): Displays serial ports’ interrupt and location. Change Setting: Change serial port settings and suggest setting “Auto” as default.
Shenzhen Maxtang Computer Co., Ltd 3.3.8 Hardware Monitor PC Health Status The PC health status displays CPU temperature, system temperature, fan speed, and other relevant voltage values. The above parameters have a certain range, and the system cannot run beyond these ranges.
Shenzhen Maxtang Computer Co., Ltd 3.3.10 S5 RTC Wake Settings Wake system From S5: timing boot settings, disabled by default. Fixed Time: Select Fixed Time and the system will wake on the Hr: Min: Sec specified. Dynamic Time: Select Dynamic Time and the system will wake on a dynamic time.
Shenzhen Maxtang Computer Co., Ltd 3.3.11 USB Configuration Legacy USB Support Enable Legacy USB support. Disables legacy support if no USB devices are connected. Select enable will keep USB devices available under UEFI’s support. XHCI Hand-off Whether to enable the USB XCHI transfer protocol. A workaround for OS without XHCI hand-off support.
Shenzhen Maxtang Computer Co., Ltd 3.3.14 NVMe Configuration The capacity and model of the SSD will be displayed under the option after the NVMe protocol SSD has been installed.
Shenzhen Maxtang Computer Co., Ltd 3.4 Chipset Select the chipset tab from the setup screen to enter the chipset BIOS Setup screen. System Agent (SA) Configuration: Northbridge configuration options, including video memory, display devices, and other options. PCH-IO Configuration: Southbridge configuration options, including hard disk, sound card equipment, and...
Shenzhen Maxtang Computer Co., Ltd 3.4.1 System Agent (SA) Configuration Memory Configuration Graphics Configuration DMI/OPI Configuration VMD setup menu: In order to set up the RAID mode, please enter this menu and set the “Enable VMD controller” to “Enabled”. PCI Express Configuration...
Shenzhen Maxtang Computer Co., Ltd 3.4.2 PCH-IO Configuration PCI Express Configuration SATA Configuration USB Configuration Security Configuration HD Audio Configuration PCH LAN Controller State After G3 setting: S0 State (auto-start after power-on), S5 State by default.
Shenzhen Maxtang Computer Co., Ltd 3.5 Security Administrator Password: Set the Administrator Password. User Password: Set User Password. Secure Boot: Secure boot...
Shenzhen Maxtang Computer Co., Ltd 3.6 BOOT Setup Prompt Timeout: Number of seconds that the firmware will wait before initiating the original default boot selection. A value of 0 indicates that the default boot selection is to be initiated immediately on boot. A value of 65535(0xFFFF) indicates that firmware will wait for user input before booting.
Shenzhen Maxtang Computer Co., Ltd 3.7 Save & Exit Save Changes and Exit: Exit the system setup after saving the changes and continue to start the computer. Discard Changes and Exit: Exit the system setup without saving any changes and continue to start the computer.
Need help?
Do you have a question about the ALD76 and is the answer not in the manual?
Questions and answers