Renault EXPRESS 2021 Vehicle User Manual

Table of Contents

Quick Links

Download this manual

eXPReSS

vehicle user manual

Table of Contents

Chapters

Table of Contents

Summary of Contents for Renault EXPRESS 2021

Page 1 eXPReSS vehicle user manual...
Page 2 Castrol, exclusive Renault partner Benefit from cutting-edge technology born out of competition to ensure the performance and longevity of your Renault thanks to wide range of engine lubricants developed specially by Renault and Castrol. Renault recommends renault.fr...
Page 3 Welcome aboard your vehicle This driver’s handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
Page 4 EXTERIOR Electric windows ➥ 3.10 Windscreen wipers ➥ 1.88 Rear view mirrors Demisting ➥ 3.4 ➥ 1.81 Key/Remote control ➥ 1.2 Locking/unlocking the doors ➥ 1.6 Bodywork maintenance ➥ 4.16 Lights: operation ➥ 1.83 Tyres ➥ 5.13 Lights: replacement ➥ 5.16 Filling with fuel ➥...
Page 5 PASSENGER COMPARTMENT Passenger compartment stor- Adjusting your driving po- age/fittings ➥ 3.15 Rear bench seat ➥ 3.24 sition ➥ 1.20 Rear headrests ➥ 3.22 Front seats ➥ 1.15 Front headrests ➥ 1.14 Child safety ➥ 1.34 Transporting objects in the luggage compartment ➥...
Page 6 DRIVER’S POSITION Instrument panel ➥ 1.60 Trip computer controls ➥ 1.67 Exterior lighting ➥ 1.83 Multimedia screen ➥ 3.34 Cruise control ➥ 2.33 Speed limiter ➥ 2.30 Heated seat(s) ➥ 1.15 Bonnet release ➥ 4.2 Heating/Air conditioning system ➥ 3.4 Gearstick ➥...
Page 7 DRIVING AIDS ABS (anti-lock braking system) ESC (electronic stability control) Braking assistance Hill start assistance Driver assistance with a trailer Traction control - Extended grip ➥ 2.25 Speed limiter ➥ 2.30 Blind spot warning ➥ 2.42 Parking distance control ➥ 2.37 Cruise control ➥...
Page 8 SAFETY ON BOARD Front Airbags ➥ 1.26 Curtain Airbags ➥ 1.32 Inhibiting the front passenger airbag ➥ 1.52 Side Airbags ➥ 1.32 Seat belts ➥ 1.20...
Page 9 IDENTIFYING A VEHICLE - LABELS Technical Information for the emergency services ➥ 6.3 Review of a vehicle identification number ➥ 6.2 Vehicle identification plate ➥ 6.2 Engine identification ➥ 6.4 Tyre pressure labels ➥ 2.18 ➥ 4.14...
Page 10 THE ENGINE COMPARTMENT (routine maintenance) Windscreen washer fluid ➥ 4.9 Brake fluid ➥ 4.9 Coolant level ➥ 4.9 Engine oil filler cap ➥ 4.6 Engine oil dipstick ➥ 4.4 Battery ➥ 5.33 Opening the bonnet ➥ 4.2...
Page 11 BREAKDOWN RECOVERY Replacing the wiper blades Puncture: ➥ 5.35 Tools ➥ 5.9 Emergency spare wheel ➥ 5.2 Replacing headlight Changing a wheel bulbs ➥ 5.16 ➥ 5.11 Front towing point ➥ 5.37 Replacing rear light bulbs ➥ 5.19 Replacing a wiper blade Fuses ➥...
Page 12 0.10...
Page 13 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........0.11...
Page 14 0.12...
Page 15: Table Of Contents
Section 1: Getting to know your vehicle Keys, radio frequency remote control: general information, use ......Locking, unlocking the opening elements .
Page 16: Keys, Radio Frequency Remote Control: General Information, Use
KEYS, RADIO FREQUENCY REMOTE CONTROLS: general information (1/2) 1 Locks all the opening elements. 2 Unlocks all the opening elements. 3 Driver’s door and ignition key. 5 Locking/unlocking the luggage com- partment and, depending on the ve- hicle, the sliding doors. Driver’s responsibility when parking or stopping Remote control with switchblade...
Page 17 KEYS, RADIO FREQUENCY REMOTE CONTROLS: general information (2/2) Radio frequency remote control operating range This varies according to the environ- ment: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Note: depending on the vehicle, if a Replacement and additional keys door or the luggage compartment is or remote controls...
Page 18 KEYS, RADIO FREQUENCY REMOTE CONTROL: use (1/2) The remote control A can be used to Note lock or unlock the doors and boot. With the ignition on and engine running It is powered by a battery which can be ➥ 2.3, buttons on the remote control replaced.
Page 19 KEYS, RADIO FREQUENCY REMOTE CONTROL: use (2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the...
Page 20: Locking, Unlocking The Opening Elements
LOCKING AND UNLOCKING THE OPENING ELEMENTS (1/2) If the remote control does not work In some cases, the radio frequency remote control may not work: – radio frequency remote control bat- tery worn out or vehicle battery dis- charged, etc. –...
Page 21 LOCKING AND UNLOCKING THE OPENING ELEMENTS (2/2) Door and tailgate status Locking the opening indicator elements without the radio frequency remote control When the ignition is on, the indicator light above the 4 switch informs you of For example, in the event of a dis- the locking status of the opening ele- charged battery or the radio frequency ments:...
Page 22: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Operating faults Note: if a door is opened or closed, it will automatically lock again when the If you experience an operating fault (no vehicle reaches a speed of approxi- automatic locking, the 1 switch warning mately 4 mph (7 km/h).
Page 23: Opening And Closing The Doors
OPENING AND CLOSING THE DOORS (1/5) Front doors Lights-on warning buzzer Door/tailgate open buzzer If you have left the lights on after switch- Depending on the vehicle, this alarm is Opening from the outside ing off the ignition, a reminder buzzer fitted to the driver’s side door or on all With the doors unlocked ➥...
Page 24 OPENING AND CLOSING THE DOORS (2/5) Recommendations con- cerning the sliding side door The following precautions must be taken when opening and closing the doors or any other open- ing element: – check that no person, animal or object is at risk of being harmed when you perform this manoeu- vre;...
Page 25 OPENING AND CLOSING THE DOORS (3/5) Opening from the inside Manual locking Manual unlocking Pull the handle 7 and slide the door With the 8 button in the unlocked posi- With the button 8 in the locked position, towards the rear of the vehicle until it tion, turn it towards the front of the vehi- turn it towards the rear of the vehicle locks in position.
Page 26 OPENING AND CLOSING THE DOORS (4/5) Rear hinged doors Opening the small door Opening the doors to the maximum position Move the lever 10 to open the small Opening the large door door. For each door, pull handle 11 to release Unlock the door and pull handle 9.
Page 27 OPENING AND CLOSING THE DOORS (5/5) Manual locking If the remote control does not work, you can manually lock the rear doors. With the large door open, turn the Driver’s responsibility when parking or stopping the vehicle bolt 12 (using a tool such as a flat-blade screwdriver) and close the door.
Page 28: Headrests
FRONT HEADRESTS To remove the headrest Press button 2 and lift the headrest to release it (tilt the seatback backwards, if necessary). To refit the headrest Insert the headrest rods in the holes 1, with the notches facing forwards (tilt the seat backwards if necessary).
Page 29: Front Seats
FRONT SEATS (1/2) To move the seat forwards or To tilt the seatback back Turn the knob 3, or, depending on the vehicle, pull the lever 4 to tilt the seat Lift and hold the bar 1 to unlock the back to the desired position and make seat.
Page 30 FRONT SEATS (2/2) After making adjustments, make sure that the seat- backs are correctly locked in place. For safety reasons, carry adjustments when the vehicle is not Heated seats For vehicles with a single sliding side being driven. door, in the event of an emergency, the (depending on vehicle) rear passengers may exit the vehicle We would advise you not to recline...
Page 31 FRONT PASSENGER SEATS: functions (1/2) Before returning the seat to the comfort position, ensure that no objects will ob- struct in moving the seat. – Pull lever 1 upwards; – raise the seatback 2; – check that it is correctly locked; –...
Page 32 FRONT PASSENGER SEATS: functions (2/2) Folding down the seat Before returning the seat to the comfort position, ensure that no objects will ob- – Move the seat as far back as possi- struct in moving the seat. ble ➥ 1.15; –...
Page 33: Swivelling Partition
SWIVELLING PARTITION When moving the swivelling parti- tion, ensure the seat belt is not dam- aged. Hold it aside when you rotate the partition. When the front seatback is in the table position or folded down, depending on the vehicle, you must de- To rotate the partition To put the partition back into its initial activate the front passenger airbag...
Page 34: Seat Belts
SEAT BELTS (1/6) Always wear your seat belt when trav- Adjusting your driving position elling in your vehicle. You must also (depending on the vehicle) – Sit well back in your seat (having comply with the legislation of the par- ticular country you are in.
Page 35 SEAT BELTS (2/6) Unfastening Press button 4 on catch 5, and the seat belt will be rewound by the inertia reel. Guide the belt. ß Driver’s seat belt reminder and, depending on the vehi- cle, front passenger seat belt re- minder This appears on the central display A when the ignition is switched on and...
Page 36 SEAT BELTS (3/6) When the vehicle speed is below ap- proximately 12 mph (20 km/h), the graphic 6 or 7 appears during approx- imately 60 seconds every time one of the rear seat belts is fastened or unfas- tened. When the vehicle speed is above ap- proximately 12 mph (20 km/h), if one of the rear seat belts is or becomes unfas- ß...
Page 37 SEAT BELTS (4/6) Adjusting the height of the Rear side seat belts 9 front seat belts The belts are locked and unlocked in the same way as the front seat belts. Press button 8 to adjust the seat belt Make sure that the rear bench seat height so that shoulder strap 1 is worn is locked in position correctly so that as shown previously:...
Page 38 SEAT BELTS (5/6) Five-seater version Four-seater version: This version differs in that it has rear Centre seat belt seatbelts and headrests on the rear Unwind belt 15 slowly from its hous- side seats only. ing 10. Pass the two buckles and the belt 15 in the belt guide 11.
Page 39 SEAT BELTS (6/6) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 40 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/6) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt pretensioners; an accident. – chest force limiters; – No operation whatsoever is permitted on any part of the –...
Page 41 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/6) Load limiter Each airbag system consists of: – an airbag and its gas generator fitted Above a certain severity of impact, this on the steering wheel for the driver mechanism is used to limit the force of and, depending on the vehicle, in the the belt against the body so that it is at...
Page 42 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/6) Operating faults å This warning light comes on when the engine is started and then goes out after approximately three sec- onds. If it does not come on when the ignition is switched on or if it stays on, there is a fault in the system.
Page 43 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/6) The following cases trigger the pre- In a frontal impact with another vehi- In a side impact with another vehicle tensioners or airbags. cle of an equivalent or higher category, of an equivalent or higher category, at with an impact area equal to or greater an impact speed equal to or greater...
Page 44 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/6) In the following examples, the pre- In the following examples, the pre- – side impact to the front or rear of the tensioners and airbags could oper- tensioners and airbags might not vehicle;...
Page 45 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (6/6) All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. Warnings concerning the driver’s airbag –...
Page 46 SIDE PROTECTION DEVICES Depending on the vehicle, this is com- posed of: Side Airbags This airbag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact.
Page 47 ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt, the airbag and the seat belt are integral parts of the same protection system.
Page 48: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult.
Page 49 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 50 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier Up to 18 kg or 4 years, the child may From 15 kg or 4 years, the child can than that of an adult and its neck is very travel on a forward-facing seat.
Page 51: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/3) There are two ways of attaching child Attachment via the seat belt seats: via the seat belt or using the The seat belt must be adjusted to ISOFIX system. ensure that it is effective in the event of harsh braking or an impact.
Page 52 CHILD SAFETY: choosing a child seat mounting (2/3) Attachment using the ISOFIX Attach the child seat with the ISOFIX system locks, if these are provided. The ISOFIX system allows quick, easy and safe fit- Authorised ISOFIX child seats are ap- ting.
Page 53 CHILD SAFETY: choosing a child seat mounting (3/3) Anchorages 2 must be used to attach the child seat’s upper strap. It is forbidden to use other mounting points to attach this strap. Attachment using the ISOFIX system (continued) The ISOFIX anchorage The third ring 2 of each rear seat is points have been exclu- used to attach the upper strap on some...
Page 54: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat: general information (1/2) Some seats are not suitable for fitting The types of child seats indicated may After installing the child seat, when this child seats. The diagrams on the fol- not be available. Before using a differ- is possible, you can move the vehi- lowing pages show you how to attach ent child seat, check with the manufac-...
Page 55 CHILD SAFETY: fitting a child seat: general information (2/2) In the rear side seat Always remove the headrest from the Rear centre seat rear seat on which the child seat is po- (depending on the vehicle) A carrycot can be installed across the sitioned.
Page 56 CHILD SAFETY: attachment by seat belt (1/6) Installation visual for the five-seat estate version ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats.
Page 57 CHILD SAFETY: attachment by seat belt (2/6) Installation visual for the four-seat estate version ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats.
Page 58 CHILD SAFETY: attachment by seat belt (3/6) The table below summarises the information already shown on the diagram on the previous pages, to ensure the regu- lations in force are respected. Estate version Front passenger seat Rear seats without Centre seat Type of child seat Weight of the child with airbag...
Page 59 CHILD SAFETY: attachment by seat belt (4/6) Refer to the “Child safety equipment” booklet available from the network to choose the seat suited to your child and rec- ommended for your vehicle. X = Seat not suitable for fitting child seats. U = Seat allowing a child seat with “Universal”...
Page 60 CHILD SAFETY: attachment by seat belt (5/6) The table below summarises the information already shown on the diagram on the next page, to ensure the regulations in force are respected. Van version Front passenger seat Type of child seat Weight of the child with airbag without without passenger airbag deactivation...
Page 61 CHILD SAFETY: attachment by seat belt (6/6) Van model installation diagram ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats. Child seat attached using the belt ¬...
Page 62 CHILD SAFETY: attachment using the ISOFIX system (1/4) Installation visual for the five-seat estate version Child seat attached using the ² ISOFIX mounting Seat not suitable for fitting child seats. ü Seat which allows an ISOFIX child seat to be fitted. The rear side seats are fitted with an anchorage point which enables the fit- ting of a universal ISOFIX forward-fac-...
Page 63 CHILD SAFETY: attachment using the ISOFIX system (2/4) Installation visual for the four-seat estate version Child seat attached using the ² ISOFIX mounting Seat not suitable for fitting child seats. ü  Seat which allows an ISOFIX child seat to be fitted. Carrying passenger STRICTLY PROHIBITED.
Page 64 CHILD SAFETY: attachment using the ISOFIX system (3/4) The table below summarises the information already shown on the diagram on the previous pages, to ensure the regu- lations in force are respected. Estate version Front passenger seat Rear seats Seat size Weight of without Centre seat...
Page 65 CHILD SAFETY: attachment using the ISOFIX system (4/4) Refer to the “Child safety equipment” booklet available from the network to choose the seat suited to your child and rec- ommended for your vehicle. X = Seat not suitable for fitting child seats. IUF = Seat which allows forward facing child seats with “Universal”...
Page 66 CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3) Front passengerairbag To deactivate theairbag : with the ve- hicle stationary and the ignition off, deactivation press and turn the lock 1 to position Before installing a child seat on the OFF. front passenger seat: With the ignition on, it is essential to The passenger airbag must...
Page 67 CHILD SAFETY: deactivating, activating AIRBAG front passenger (2/3) The markings on the dashboard and labels A on each side of the passenger sun visor 3 (as shown above) repeat these instructions. DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat, NEVER fit a rear-facing child re-...
Page 68 CHILD SAFETY: deactivating, activating AIRBAG front passenger (3/3) DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat, NEVER fit a rear-facing child re- straint system in a seat protected by an ACTIVATED front AIRBAG.
Page 69: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS é Horn Hazard warning lights Direction indicators Press one of the locations 2 to activate Press switch 3. Move stalk 1 parallel to the steering the horn. wheel and in the direction you are going This switch activates all four direction to turn it.
Page 70 DRIVER’S POSITION: LEFT-HAND DRIVE (1/4) 1.56...
Page 71: Instrument Panel
DRIVER’S POSITION: LEFT-HAND DRIVE (2/4) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 11 Location for radio, navigation system or storage compartments. 2 Side demister outlet. 12 Location for passenger airbag or 3 Stalk for: storage compartment.
Page 72 DRIVER’S POSITION: LEFT-HAND DRIVE (3/4) 1.58...
Page 73 DRIVER’S POSITION: LEFT-HAND DRIVE (4/4) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 16 Controls for: 24 Cruise control/speed limiter con- trols and main switch. – heating or air conditioning, – rear screen and door mirror de-icing. 25 Driver’s glove compartment and fuse box.
Page 74 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. © warning light means you should drive very carefully to an approved dealer as soon as pos- sible. If you fail to follow this recom- mendation, you risk damaging your vehicle.
Page 75 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Left-hand direction indicator Variable power-assisted tell-tale steering warning light Right-hand direction indica- It lights up when the ignition or the tor tell-tale engine is switched on and goes off after a few seconds.
Page 76: Warning Lights
WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ô Urgent stop warning light Coolant temperature warn- ® (red) ing light This lights up when the ignition or This lights up blue when you switch on engine is switched on and goes out as the ignition or start the engine.
Page 77 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. É Preheating warning light Anti-lock braking warning (diesel version) light This should come on when the igni- It lights up when the ignition or the tion is switched on.
Page 78 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  Ï¦ Warning light for the elec- Cruise control warning tronic stability program lights ➥ 2.33. (ESC) and traction control system Ð Speed limiter warning light This lights up when the ignition is ➥...
Page 79 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. ß Front and rear seat belt re- minder warning light ➥ 1.20. On display B  Passenger Airbag ON ➥ 1.52. ¹ Passenger Airbag OFF ➥...
Page 80: Displays And Indicators
DISPLAYS AND INDICATORS Fuel gauge 1 or 4 Trip computer and warning system A or B The number of squares lit shows the fuel level. ➥ 1.67 If the minimum level is reached, the Speedometers 2 and, warning light on the instrument depending on the vehicle, 3 panel comes on and a beep sounds.
Page 81 ON-BOARD COMPUTER: general information (1/2) Display selection keys 2 or 3 h) engine coolant temperature; i) clock and exterior temperature; Scroll through the following information by repeated short presses on button 2 j) general adjustment. or 3 (the display depends on the vehicle equipment and country): a) total mileage and trip mileage re- corder;...
Page 82 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
Page 83 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Average b) Journey parameters: Average fuel consumption.
Page 84 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range b) Journey parameters (continued): Estimated range with remaining fuel. 541 km The value is displayed after driving 400 metres.
Page 85 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message d) Service distance. With the ignition switched on, the engine not running and Service in the display set to “Service Intervals”, press button 2 or 3 for SERVICE...
Page 86 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) d) Mileage before service With the ignition on, the engine not running and the display Oil change in showing “Service Intervals”, press button 2 or 3 for about 5 sec-...
Page 87 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected e) Reset the tyre pressure. Tyre pressure ➥ 2.18. init. long press f) Trip log.
Page 88: Clock And Outdoor Temperature
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected h) Engine coolant temperature. i) Clock and outdoor temperature. j) General settings. Settings Press button 2 or 3 for approximately 5 seconds (press and hold)
Page 89 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected “Battery Low Indicates that the vehicle must be started to recharge the battery (e.g.
Page 90 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 91 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.
Page 92 CLOCK AND EXTERIOR TEMPERATURE (1/2) 12:00 Vehicles not fitted with a multimedia screen To access the 3 display for setting the time, press and hold the 1 or 2 switch for a few seconds. The hour reading flashes. You are now in setting mode, press switch 1 or 2 to set the hour.
Page 93 CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator Special note: When the exterior temperature is - 3°C to + 3°C, the °C characters flash (sig- nalling a risk of ice on the road). Vehicles fitted with a multimedia screen A The time and exterior temperature are displayed on the multimedia screen A.
Page 94: Steering Wheel, Power-Assisted Steering
STEERING WHEEL, POWER-ASSISTED STEERING Power-assisted steering Never drive with an inadequately charged battery. Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while Never leave the steering wheel on...
Page 95: Rear View Mirrors
REAR VIEW MIRRORS (1/2) Rear view mirror with lever 1 When driving at night, to avoid being dazzled by the headlights of the vehicle behind, depress the little lever located behind rear view mirror 1. Rear view mirror without lever 1 The rear view mirror darkens automa- tically at night if you are being followed by a vehicle with its lights on.
Page 96 REAR VIEW MIRRORS (2/2) Door mirrors with electrical Wide angle rear view mirror 5 The various zones seen by the driver are: adjustment: (depending on the vehicle) – C in the the wide-angle rear view Lower the sun visor 4 to access the With the ignition on, move button 3: mirror;...
Page 97: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/4) š Side lights Daytime running lights function Turn the ring 2 until the symbol (front lights only) is opposite mark 3. If fitted on the vehicle, the daytime run- This indicator light on the instrument ning lights come on automatically with panel comes on.
Page 98 EXTERIOR LIGHTING AND SIGNALS (2/4) á To switch off the dipped Main beam headlights beam headlights: With the engine running and š the dipped beam headlights lit, push – turn the ring 2 to position stalk 1. This indicator light on the instru- ment panel comes on.
Page 99 EXTERIOR LIGHTING AND SIGNALS (3/4) Rear fog light Switching off the lights Turn centre ring 4 on the stalk Turn centre ring 4 again until mark 3 until the symbol faces mark 3, then re- is opposite the symbol for the fog light lease it.
Page 100 EXTERIOR LIGHTING AND SIGNALS (4/4) To increase this duration, you may pull the stalk up to four times (total time re- stricted to two minutes). The message “Follow-me home_ _ _” along with the times the lights will be on for is displayed on the instrument panel to confirm this action.
Page 101: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT Examples of positions for adjusting control A according to the load Driver alone or with front passenger Driver with one front passenger and one rear passenger Driver with one front passenger and two rear passengers Control A is used to adjust the height of the headlight beams according to the load.
Page 102 WINDSCREEN WASH, WIPE (1/5) Vehicle fitted with intermittent Special note windscreen wipers When driving the vehicle, the wiping speed slows down whenever the ve- A single sweep hicle stops. For example, fast wiping A short push will trigger one sweep speed will slow to normal wiping speed.
Page 103 WINDSCREEN WASH, WIPE (2/5) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of reduced visibility, the driver should manually activate the wipers.
Page 104 WINDSCREEN WASH, WIPE (3/5) Operating faults Special note In the event of a malfunction of the au- When driving the vehicle, the wiping tomatic wiping, the wiper is set to inter- speed slows down whenever the vehi- mittent wiping. Contact an authorised cle stops.
Page 105 WINDSCREEN WASH, WIPE (4/5) Specific front wiper position (service position) This position enables the blades to be lifted to remove them from the winds- creen. It may be useful to: – to clean the blades; – to release the blades from the winds- creen in winter;...
Page 106 WINDSCREEN WASH, WIPE (5/5) Note: In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. Efficiency of a wiper blade Check the condition of the wiper blades.
Page 107 REAR SCREEN WASHER, WIPER (1/2) To stop the operation, pivot ring 3 again. Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate auto- matic wiping. Efficiency of a wiper blade Follow usage recommendations.
Page 108 REAR SCREEN WASHER, WIPER (2/2) In the event of obstacles present on the rear window (dirt, snow, etc.), the wiper will try to sweep away all the obstacles. If an obstacle prevents the blade from moving, it can be stopped. Remove the obstacle, wait for around 30 seconds and reactivate the wiper using the wiper stalk.
Page 109 FUEL TANK (1/4) For details on filling the fuel tank, refer to the information on “Filling with fuel”. To close it, press the cover B with your hand, as far as it will go. To fill up with fuel, the engine Depending on the vehicle, the hook A must be stopped (and not prevents the sliding side door from...
Page 110 FUEL TANK (2/4) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country. It must comply with the spec- ifications given on the label D on the inside of the flap. ➥ 6.7. Petrol versions It is essential to use unleaded petrol.
Page 111: Fuel Tank Filling With Fuel
FUEL TANK (3/4) Filling with fuel Petrol versions Special case Using leaded petrol will damage the When the vehicle has been stopped for With the ignition off, insert the nozzle to antipollution system and may lead to a around three months, you must add open the valve and insert it fully before loss of warranty.
Page 112 FUEL TANK (4/4) Running out of fuel on Diesel versions Set the ignition key to “On” position C ➥ 2.2 and wait a few minutes before starting in order to enable the fuel cir- cuit to be primed. If the engine does not start, repeat the procedure.
Page 113: Reagent Tank
REAGENT TANK (1/4) Always comply with the legislation in place in the country where you are lo- cated. Not abiding by the regulations in To fill up with reagent, the engine force may expose the vehicle owner to must be stopped (not just on prosecution.
Page 114 REAGENT TANK (2/4) Filling (continued) If the reagent overflows, or contami- nates any paintwork, clean the affected The tank can be filled at the pump. With area quickly with plenty of cold water the ignition off, insert the nozzle and and a soft cloth.
Page 115 REAGENT TANK (3/4) Maintenance/Range The information displayed on the instrument panel may be accompanied by a beep. Indicator lights Message What to do? When the message is displayed when the ignition is switched on, you have less “Top Up AdBlue than 1,488 miles (2,400 km) range.
Page 116 REAGENT TANK (4/4) System faults The information displayed on the instrument panel may be accompanied by a beep. Indicator lights Message Readings “CHECK ANTI- POLLUTION SYSTEM”  Indicates a fault in the system. Contact your approved © “AdBlue quality to check” come dealer as soon as possible.
Page 117 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Ignition switch .
Page 118: Running In
RUNNING IN, IGNITION SWITCH Petrol version “Ignition” position C For the first 600 miles (1,000 km), do The ignition is switched on: not exceed 80 mph (130 km/h) in the – petrol version: the engine may be highest gear, or 3,000 to 3,500 rpm. started.
Page 119: Starting, Stopping The Engine
STARTING, STOPPING THE ENGINE (1/2) Starting the engine Petrol version – Turn the key to the start position Depending on the vehicle, if a gear is without depressing the accelera- engaged, for the engine to be started, tor. you must depress the clutch pedal or put the gear lever in neutral.
Page 120 STARTING, STOPPING THE ENGINE (2/2) Stopping the engine With the engine idling, turn the key Driver’s responsibility back to the “Stop” position. when parking or stopping Special note vehicle Depending on the vehicle, accessories Never leave an animal, child or adult (e.g.
Page 121 STOP AND START function (1/3) This system enables a reduced fuel For all vehicles: consumption and lower greenhouse  gas emissions. The warning light on the instru- The system is activated automatically ment panel is lit when the engine is on when the vehicle is started.
Page 122 STOP AND START function (2/3) Preventing the engine from Conditions for coming out of Conditions preventing the standing by engine standby standby of the engine In certain situations, such as negoti- For manual gearboxes: Certain conditions prevent the system ating a crossroads for instance, it is from using the engine standby function, –...
Page 123: Stop And Start Function
STOP AND START function (3/3) Special feature of the automatic The system is automatically reactivated engine re-start each time the vehicle is started using the start button. ➥ 2.3. Under certain conditions, the engine can restart on its own in order to guar- antee your safety and comfort.
Page 124 SPECIAL FEATURES OF PETROL VERSIONS PARTICLE FILTER (1/2) The following operating conditions: If you notice any of the above operat- ing faults, have the necessary repairs – driving for long periods when the low carried out as soon as possible by an fuel level warning light is lit;...
Page 125: Special Feature Of Petrol Versions, Particle Filter
SPECIAL FEATURES OF PETROL VERSIONS PARTICLE FILTER (2/2) Particle filter Note: The indicator light may go out If the filter becomes saturated, the © after 20 minutes when the driving con- warning light and, depending The particle filter is used in the treat- ...
Page 126: Special Features Of Diesel Versions, Particle Filter
SPECIAL FEATURES OF DIESEL VERSIONS: PARTICLE FILTER (1/2) Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- To avoid any faults in icy weather: tion pump which prevents the engine – ensure that the battery is always fully speed being exceeded irrespective of charged, the gear selected.
Page 127 SPECIAL FEATURES OF DIESEL VERSIONS: PARTICLE FILTER (2/2) Particle filter Note: the warning light may reappear If the filter becomes saturated, the © if the driving conditions are not fully warning light and, depending The particle filter is used in the treat- ...
Page 128: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO DRIVING (1/4) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactur- ers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 129 DRIVING ADVICE, ECO DRIVING (2/4) ECO mode Activating the function Disabling the function Press switch 2. Press switch 2. ECO mode is a function which opti-   mises fuel consumption. It affects cer- Warning light 3 goes out on the tain driving operations (acceleration, The 3 warning light comes on on...
Page 130 DRIVING ADVICE, ECO DRIVING (3/4) – Do not overrev the engine in the in- termediate gears. You should always use the highest gear possible. – Avoid sudden acceleration. – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- vance, you may then simply release the accelerator pedal.
Page 131 DRIVING ADVICE, ECO DRIVING (4/4) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 132: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele- recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must end of their service life, which entered nents with parts other than those origi- be replaced.
Page 133: Environment
ENVIRONMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved For the usage phase, your vehicle was its entire service life: during production, centres to ensure that it is recycled.
Page 134: Tyre Pressure Loss Warning
TYRE PRESSURE LOSS WARNING (1/3) Resetting the standard level for the tyre pressures This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended);...
Page 135 TYRE PRESSURE LOSS WARNING (2/3) Note: « PUNCTURE » The standard tyre pressure cannot be  less than that recommended and indi- The warning light comes on cated on the door frame. steady, accompanied by the message “PUNCTURE” and a beep. Display This message appears along with the ®...
Page 136 TYRE PRESSURE LOSS WARNING (3/3) Replacing wheels/tyres Tyre repair product and « CHECK TYRE PRESSURE SENSORS » inflation kit This system requires specific equip-  ment (wheels, tyres, hubcaps, etc.). As the valves are specifically designed, The warning light flashes for ➥...
Page 137: Gear Lever, Handbrake
GEAR LEVER, HANDBRAKE Handbrake An impact to the under- side of the vehicle while To release manoeuvring (e.g.: strik- Pull lever 3 up slightly, press button 2 ing a post, raised kerb or and then lower the lever to the floor. other street furniture) may result in damage to the vehicle (e.g.: defor- The warning light...
Page 138: Rear Camera
REAR CAMERA (1/3) Special features When the vehicle ignition is switched This function is an additional on, the screen 2 fixed to the wind- The camera is equipped with an auto- aid. It cannot, therefore, screen will display a warning message matic de-icer which is activated when under any circumstances for approximately five seconds, then it...
Page 139 REAR CAMERA (2/3) Switching off the function The display switches of: – immediately when engaging reverse gear; – 30 seconds after the ignition is switched off. Operation The camera’s field of vision does not cover the entire area behind the vehi- cle, particularly the blind spot area A.
Page 140 REAR CAMERA (3/3) Operating faults Adjustment of brightness modes Once the mode has been selected, When the system detects an operating press button 5as many times as re- fault, warning light B appears temporar- quired to access the type of setting you ily on screen 2.
Page 141: Driver Correction Devices And Aids
DRIVER CORRECTION DEVICES, AIDS (1/5) Anti-lock braking system Depending on the vehicle, this is com- Operating faults: posed of: (ABS) © – lit up on the in- – anti-lock braking system (ABS); strument panel accompanied by the Under heavy braking, the ABS prevents messages “CHECK ABS”, “CHECK the wheels from locking, allowing the –...
Page 142 DRIVER CORRECTION DEVICES, AIDS (2/5) Electronic stability control Understeer control Operating faults (ESC) with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced under- ing fault the message “Check ESC” and ...
Page 143 DRIVER CORRECTION DEVICES, AIDS (3/5) The traction control system offers ad- Hazard warning lights switching on ditional safety. It is recommended that Depending on the vehicle, these may you do not drive with the function disa- light up in the event of sudden decel- bled.
Page 144 DRIVER CORRECTION DEVICES, AIDS (4/5) Hill start assistance Driver assistance with a trailer Depending on the gradient of the in- This system helps to maintain control cline, this system assists the driver over the vehicle while using a trailer. when starting on a hill. It prevents the The hill start assistance It detects shaking caused by towing a vehicle from rolling backwards by au-...
Page 145 DRIVER CORRECTION DEVICES, AIDS (5/5) Traction control - Extended “Soft ground” mode grip Press the 2 switch: the message “Grip Extend Loose Surface ON” is displayed If fitted on the vehicle, grip control on the instrument panel. makes it easier to control the vehicle on low grip surfaces (soft ground, etc.).
Page 146: Speed Limiter
SPEED LIMITER (1/3) Controls Switching on The speed limiter function helps you stay within the driving speed limit that 1 Main “On/Off” switch. Press switch 1 on the side showing you choose, known as the limit speed.  . The warning light 5 illuminates in 2 Reminder of the stored limit speed orange and, depending on the vehi- and increase of the limit speed...
Page 147 SPEED LIMITER (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 148 SPEED LIMITER (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 2 (RES/+). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is sus- case a speed is no longer stored.
Page 149: Cruise Control
CRUISE CONTROL (1/4) This function is an addi- tional driving aid. The func- tion does not take the place of the driver. Therefore, it can under no circum- Controls The cruise control function helps you to stances replace the driver’s respon- maintain your driving speed at a speed sibility to respect speed limits and to 1 Main “On/Off”...
Page 150 CRUISE CONTROL (2/4) Switching on Activating cruise control Driving  At a steady speed (above approxi- Once a cruising speed is stored and Press switch 1 on the side showing mately 19 mph (30 km/h)) press the the cruise control function is active, The 6 warning light appears in green switch 3 (SET/-): the function is acti- you may lift your foot off the accelera-...
Page 151 CRUISE CONTROL (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 152 CRUISE CONTROL (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road condi- tions are suitable (traffic, road surface, weather conditions, etc.). Press the switch 2 (RES/+) if the vehicle speed is above 19 mph (30 km/h).
Page 153: Parking Distance Control
PARKING DISTANCE CONTROL (1/3) Operating principle Ultrasonic sensors, indicated by arrows 1, are fitted in the bumpers to measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when This function is an addi- the vehicle is approximately 20 to...
Page 154 PARKING DISTANCE CONTROL (2/3) Operation Most objects located near the rear and, depending on the vehicle, near the front end are detected. Depending on the vehicle, the areas will be shown on the 2 display. Note: the display 2 shows the vehicle surroundings and emits beeps.
Page 155 PARKING DISTANCE CONTROL (3/3) Operating faults You must disable the function if: – towing, carrying or trailer equipment Depending on the vehicle, when the is present in front of the ultrasonic system detects an operating fault, the detectors; message “Parking sensors to check” appears on the instrument panel, ac- –...
Page 156: Reversing Camera
REVERSING CAMERA (1/2) Operation Note: depending on the vehicle, certain settings can be adjusted from the multi- Moving into reverse gear, the camera 1 media screen 3. Refer to the handbook located on the rear hinged door pro- for the equipment. vides a view of the area behind the vehicle on the rear view mirror 2 or, depending on the vehicle, on the mul-...
Page 157 REVERSING CAMERA (2/2) This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately.
Page 158: Blind Spot Warning
BLIND SPOT WARNING (1/4) This function is an addi- tional aid which indicates other vehicles in the blind spot area. Special feature This system alerts the driver to other It can never in any case be a subs- vehicles in the detection zone A. Make sure that the sensors are not obs- titute for care nor for the driver’s The system is activated when the vehi-...
Page 159 BLIND SPOT WARNING (2/4) Operation This function gives a warning: – when the vehicle speed is between approximately 19 mph (30 km/h) and 87 mph (140 km/h); – when another vehicle is in the blind spot area and travelling in the same direction as your vehicle.
Page 160 BLIND SPOT WARNING (3/4) Display D When the direction indicator is acti- vated, the indicator light 3 flashes when a vehicle is detected in the blind spot on the side towards which you are about to steer. If you cancel the direction indica- tor, the function will return to the initial warning (display C).
Page 161 BLIND SPOT WARNING (4/4) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- played on the instrument panel. Call an approved Dealer. Note: when the engine is started, the indicator light 3, display B, flashes three times.
Page 162: Overspeed Function
VEHICLE WITH OVERSPEED FUNCTION Special case: if your vehicle is fitted with the Cruise control/Speed limiter, fully pressing the accelerator pedal (beyond the kickdown point) will not enable you to exceed the overspeed function set speed. ➥ 2.30. The vehicle speed may be permanently set at a fixed value depending on the vehicle or on local legislation.
Page 163: Emergency Call
EMERGENCY CALL (1/3) If the vehicle is equipped, the emer- gency call system enables the emer- gency services to be called (without charge) automatically or manually in the event of an accident or illness, in order to reduce the time they take to arrive on the scene.
Page 164 EMERGENCY CALL (2/3) Automatic mode In the event of unintended operation, it is possible to cancel the call by press- If the automatic mode 2 warning light ing the 3 button for around two sec- appears in green this confirms that the onds, before the call is connected to automatic system is activated.
Page 165 EMERGENCY CALL (3/3) The system operates with a dedi- cated battery. The battery service life is approximately four years (the 1 warning light lights up in red to warn you when approaching expiry). Without the emergency call feature, Consult an approved dealer the system is not trackable and will not be under constant surveillance.
Page 166 2.50...
Page 167 Section 3: Your comfort Air Vents ..............Heating, air conditioning .
Page 168: Air Vents
AIR VENTS, air outlets (1/2) 6 Right-hand air vent 1 Left-hand air vent 7 Passenger footwell heater outlets 2 Left-hand side window demisting 8 Control panel vent 9 Footwell heater outlets for rear 3 Windscreen demisting vents passengers (depending on the 4 Centre air vents vehicle) 5 Right-hand side window demister...
Page 169 AIR VENTS, air outlets (2/2) Centre 4 and side vents 1 Rear seats and 6 (depending on vehicle) Passenger footwell heater outlets 9. Air flow To close: move the cursor 10 towards the outside of the vehicle beyond the resistance point. To open: move the cursor 10 towards the inside of the vehicle.
Page 170: Heating, Air Conditioning
HEATING, AIR CONDITIONING (1/4) Adjusting the air temperature Turn control 5 to obtain the desired temperature. The further towards the red the slide is, the higher the temper- ature will be. Adjusting the ventilation fan speed. Move control 3 from 0 to 4. The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment.
Page 171 HEATING, AIR CONDITIONING (2/4) Switching passenger Air recirculation is used to: compartment isolation mode/ – to isolate the passenger compart- air recirculation mode on. ment from the external atmosphere (e.g. driving in polluted areas, etc.); (depending on the vehicle) Prolonged use of air recirculation â...
Page 172 HEATING, AIR CONDITIONING (3/4) Rapid demisting Rear screen and/or exterior rear view mirror de-icing/ Turn controls 1, 3 and 6 to: demisting. – demisting With the engine running, press button 2. The operating tell-tale comes – ventilation speed 3 or 4; –...
Page 173 HEATING, AIR CONDITIONING (4/4) Distribution of air in the The air flow is mainly distrib- uted between the front and passenger compartment rear footwells and the dashboard vents. Turn control 1 to choose the distribution Close the dashboard vents to direct all option.
Page 174 AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations (air conditioning off, You will normally notice an increase in As a general rule, contact your ap- air recirculation activated, ventilation fuel consumption (especially in town) proved Dealer in the event of an oper- speed at zero or low etc.), you may when the air conditioning is operating.
Page 175 AIR CONDITIONING: information and operating instructions (2/2) Ñ Type of refrigerant fluid  Type of oil in the air condi- tioning circuit  Inflammable product  Consult the driver’s hand- book  Maintenance Quantity of refrigerant fluid present in the ve- x.xxx kg hicle.
Page 176: Electric Windows
ELECTRIC WINDOWS (1/2) Driver’s responsibility Never leave your vehicle with the key inside, and with a child, a dependent adult or a pet, even for a short while. They may pose a risk to themselves or to others by starting the engine or activating equipment (such as the Electric windows From the driver’s seat, use switch:...
Page 177: Half-Opening Window
ELECTRIC WINDOWS (2/2) One-touch electric windows Operating faults When the vehicle is equipped with this In case of a fault when closing a function, the one-touch mode works in window, the system reverts to normal addition to the operation of the electric mode: pull the switch concerned up as windows described previously.
Page 178: Interior Lighting
INTERIOR LIGHTING (1/2) Courtesy light Map reading lights (depending on vehicle) Pressing switch 1 provides: Pressing switch 2 provides: – continuous lighting; – continuous lighting; – or temporary lighting by opening one – or temporary lighting by opening one of the front doors, or by opening one of the front doors, or by opening one of the four doors, depending on the of the four doors, depending on the...
Page 179 INTERIOR LIGHTING (2/2) Special features Depending on the vehicle, remote un- locking of the doors triggers timed light- ing of the passenger compartment. If one of the front or rear doors is opened, the period for which the light is switched on will start again.
Page 180: Sun Visor, Mirrors
SUN VISOR, MIRRORS Front sun visor Courtesy mirror 4 (passenger side) Lower the sun visor 1 or 2 over the windscreen or unclip it and turn it over the side window. Sun visor storage 3 Can be used to hold motorway toll tick- ets, maps, etc.
Page 181 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/5) Door pockets 1 Storage compartment A Driver’s dashboard upper storage compartment B Unlock the handle 2 and pull to open the storage compartment A. Put a hand in location 3 and lift to open the storage compartment B.
Page 182 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/5) Storage compartment 4 Central storage compartment 6 Cup holder 5 Storage compartment 7 Dashboard storage 8 When turning corners, Ensure that no hard, heavy accelerating or braking, or pointed objects are ensure that the recepta- placed in the “open”...
Page 183 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/5) Centre console storage Glove box Passenger storage compartment/Wireless compartment 11 and 12 If fitted on the vehicle, pull paddle 10 to charger - induction open. charging 9 For more information on the induction charging area ➥...
Page 184 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/5) Front upper cab storage Sliding side door storage Cup holder 15 compartment 13 compartment 14 Do not use it for getting into or out of the Items stored in the sliding side door vehicle and do not hang from it.
Page 185 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (5/5) Storage compartment 16 Rear bench seat central storage compartment 17 Retaining straps 18 They can be used, for example, to retain a multimedia tablet etc. Rear parcel shelves 19 Raise them to their horizontal position. Front seat storage pockets 20 3.19...
Page 186 ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET (1/2) Ashtray 1 Cigarette lighter or accessories socket 3 It can be housed in location 2 or 4. With the ignition on, push in the ciga- Lift the cover to open. rette lighter 3. It will spring back with a To empty, pull the ashtray towards you click when it is ready.
Page 187 ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET (2/2) Accessories socket 5, 6 and 7 (depending on the vehicle) They are provided for connecting ac- cessories approved by our Technical Department. Only connect accessories of maximum power 120 watts (voltage 12 V). When several accessory sockets are used at the same time, the total power of the connected accessories must not exceed...
Page 188: Rear Headrests
REAR HEADRESTS (1/2) Five-seater version To put the headrest back in place 1 Insert the rods into the holes, press the Position for using headrest 1 tab(s) 2 and lower the headrest. Lift the headrest to maximum height, Check that the bonnet is correctly then lower it until it locks.
Page 189 REAR HEADRESTS (2/2) Four-seater version This version differs in that it has rear seatbelts and headrests on the rear side seats only. The headrest is a safety component. Ensure that it is fitted and in the correct po- sition: the top of your head should be in line with the top of the headrest.
Page 190: Rear Bench Seat
REAR BENCH SEAT: functions (1/4) When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger’s arm or leg, a pet, gravel, cloth, toys, etc.). Check that the rear seat belts are positioned and Fixed rear bench seat To reposition the seatback operating correctly each –...
Page 191 REAR BENCH SEAT: functions (2/4) Five-seater version – lift the A seat or the bench seat B until it is positioned vertically (move- Rear bench seat with folding seat ment C); back and seat cushion – adjust the front seats, making sure they are properly locked in place.
Page 192 REAR BENCH SEAT: functions (3/4) Four-seater version: To reposition the seat A or the bench seat B: This version differs in that it has rear – Lower the seat base until it locks seatbelts and headrests on the rear (movement E); side seats only.
Page 193 REAR BENCH SEAT: functions (4/4) Check that the rear seat belts are positioned and operating correctly each time the rear bench seat is moved. Restriction of use It is illegal to drive with one When refitting the seat- of the second row seats back, make sure it is cor- folded down if a passenger rectly locked in place.
Page 194: Transporting Objects
TRANSPORTING OBJECTS IN THE BOOT (1/2) Always position the objects trans- ported so that the largest surface is against: – the rear bench seatbacks, for normal loads (example: A); – the front seatbacks with the rear seatbacks folded down, as is the Always position the heavi- case for maximum loads (exam- est items directly on the...
Page 195 TRANSPORTING OBJECTS IN THE BOOT (2/2) For your safety, check that all the vehicle’s doors are properly closed before starting the engine. Transporting objects in the Special note for van version While driving with the right rear load area rear hinged door open, Rotary rings 2: always secure transported Depending on the vehicle, fixed rings 1...
Page 196 TRANSPORTING OBJECTS towing, attachments Maximum dimension A = 855 mm. Permissible nose weight, maxi- mum permissible towing weight braked and unbraked ➥ 6.9. Choice and fitting of towing Any towing device must not ob- equipment struct any lighting component or Maximum weight of towing equip- the number plate when not in use.
Page 197 TRANSPORTING OBJECTS Luggage net Fitting the luggage net Fitting the luggage net On equipped vehicles, the luggage net can be used, when transporting ani- behind the rear seats behind the front seats mals or luggage, to separate them from Inside the vehicle on each side: Inside the vehicle on each side: the passenger section.
Page 198: Luggage Cover
LUGGAGE COVER How to remove the luggage Removing the luggage compartment cover A compartment cover Using handle 1, pull it gently to release Push the luggage cover to the right the pins from their mounting points, lo- (movement B) and lift the left-hand side cated on each side of the luggage com- of the inertia reel.
Page 199: Roof Bars
ROOF BARS The attaching of any carry- ing device (bike rack, lug- gage box, etc.) resting on the luggage compartment lid is prohibited. To install a carrying device on your vehicle, contact an Approved Dealer. Vehicles fitted with Vehicles not fitted with longitudinal roof bars longitudinal roof bars If fitted on the vehicle, you can trans-...
Page 200: Multimedia Equipment
MULTIMEDIA EQUIPMENT (1/2) Sockets USB 1 The sockets USB can only allow re- charge accessories approved by the brand's Technical Services of power not exceeding 12 watts (voltage 5 V) per outlet. Multimedia socket 3 You can use USB socket to access the multimedia content of your accessories.
Page 201 MULTIMEDIA EQUIPMENT (2/2) Charging procedure Place your telephone at the centre of With the engine running, check that the induction area 6. the warning light turns orange when Phone charging is interrupted in the fol- the telephone is positioned in the in- lowing cases: duction charging area 6.
Page 202 3.36...
Page 203 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 204: Bonnet
BONNET (1/2) Opening the bonnet To open the bonnet, open a door and pull the 1 handle, located on the left- To unlock, gently lift the bonnet and hand side of the dashboard. push tab 2 in the direction of arrow A to release the bonnet.
Page 205 BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close it again, hold the bonnet in the middle and lower it to 25 cm above the closed position, then release it. Ensure that the bonnet is properly closed. If it does not lock itself under its own weight, gently push it until it fully locks.
Page 206: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
Page 207 ENGINE OIL LEVEL: general information (2/2) The dipstick must be used to read the exact oil level and make sure that the maximum level has not been ex- ceeded (risk of engine damage). The instrument panel display only alerts the driver when the oil level is at its minimum.
Page 208 ENGINE OIL LEVEL: topping up, filling, oil change (1/3) Topping up/Filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
Page 209 ENGINE OIL LEVEL: topping up, filling, oil change (2/3) Exceeding the maximum engine oil level Under no circumstances should the maximum fill- ing level be exceeded: this could damage the engine and the emis- sion control system. If the oil level exceeds the maximum level, do not start your vehicle and Never run the engine in an contact an approved Dealer.
Page 210 ENGINE OIL LEVEL: topping up, filling, oil change (3/3) Oil change Consult an approved dealer at once Service interval: refer if you notice an abnormal or re- Maintenance Document for your vehi- peated drop in any of the fluid levels. cle.
Page 211: Levels
LEVELS, FILTERS (1/3) Level Topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MINI” warn- Only use fluids approved by the ing line shown on brake fluid reser- Technical Department and which have...
Page 212 LEVELS, FILTERS (2/3) Checking intervals  Power steering liquid Check the coolant level regularly fluid (very severe damage is likely to be caused to the engine if it runs out of For maintenance operations on the coolant). power-assisted steering, contact an ap- If the level needs to be topped up, only proved dealer.
Page 213: Filters
LEVELS, FILTERS (3/3) Filters Fluid Windscreen washer fluid. In winter, use The replacement of filter elements (air anti-freeze product. Use products rec- filter, cabin filter, diesel fuel filter, etc.) ommended by an authorised dealer. is scheduled in the maintenance opera- tions for your vehicle.
Page 214: Battery
BATTERY (1/2) Replacing the battery The charge status of your battery can decrease especially if you use your ve- hicle: For your own safety and for – for short journeys; the proper operation of the – for driving in town; vehicle’s electrical equip- ment (lights, windscreen –...
Page 215 BATTERY (2/2) Label A Observe the indications on the battery: – 2 Naked flames and smoking are for- bidden; – 3 Eye protection required; Please note when work- – 4 Keep away from children; ing close to the engine that –...
Page 216: Tyre Pressure
TYRE INFLATION PRESSURES (1/2) Vehicle fitted with a tyre pressure loss warning system In the event of under-inflation (punc-  tures, under-inflation etc.), the warning light appears on the instrument panel. ➥ 2.18. Label A B: dimension of the tyres fitted to the vehicle.
Page 217 TYRE INFLATION PRESSURES (2/2) Tyre safety and use of snow chains: ➥ 5.13 to learn the maintenance con- ditions and the conditions for fitting chains to different versions of the ve- hicle. For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile...
Page 218: Bodywork Maintenance
BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
Page 219 BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or Degrease or clean using freezing temperatures. high-pressure cleaning Do not scrape off mud or dirt without equipment or by spray- pre-wetting. ing on products not ap- Allow dirt to accumulate on the exterior.
Page 220 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning the headlights, finish sensors and cameras Return the wiper stalk to the park po- sition. ➥ 1.88. Check the mounting of This type of paint requires certain pre- Use a soft cloth or cotton wool.
Page 221: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle reg- temperature display, radio display, etc.) ularly.
Page 222 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in Position objects such as deodorants, the vehicle scents etc. near air vents as this could damage your dashboard trim. If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv-...
Page 223 Section 5: Practical advice Puncture, emergency spare wheel ..........Tyre inflation kit .
Page 224: Puncture, Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/4) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Do not leave the tools unsecured inside the vehicle as they may come Vehicle fitted with a tyre pressure loose under braking.
Page 225 PUNCTURE, EMERGENCY SPARE WHEEL (2/4) Depending on the vehicle, there are 2 storage options for the emergency spare wheel: – in a cradle under the floor at the rear of the vehicle; – the floor at the rear of the vehicle. Emergency spare wheel 3 This is stored in cage 5 under the floor at the rear of the vehicle.
Page 226 PUNCTURE, EMERGENCY SPARE WHEEL (3/4) Emergency spare wheel 7 To access emergency spare wheel 7 – from the outside of the vehicle, pull – Open the boot lid; the wheel in order to access the It is located under the floor at the rear –...
Page 227 PUNCTURE, EMERGENCY SPARE WHEEL (4/4) To refit the wheel 7 From the luggage compartment, tighten As the punctured wheel To carry out this operation, the cable the nut fully in an anti-clockwise direc- is wider than the emer- must be unwound. tion (movement C) in order to wind up gency spare wheel, when –...
Page 228 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 229 TYRE PRESSURE KIT (2/3) With the engine running and the If a minimum pressure of 1.8 bar is parking brake applied, not reached after 15 minutes, repair is not possible; do not drive the ve- – Disconnect any accessories previ- ously connected to the vehicle’s ac- hicle but contact an approved dealer.
Page 230 TYRE PRESSURE KIT (3/3) – Start immediately and drive at a speed between 12 to 37 mph (20 to 60 km/h) in order to distribute the product evenly in the tyre; after driv- Please be aware that a ing a distance of 2 miles (3 km), stop poorly tightened or miss- and check the pressure.
Page 231: Tools
TOOLS Wheelbrace 4 This locks and unlocks the wheel bolts and the access to emergency spare wheel. Tow eye 3 ➥ 5.37 Accessing the tools Hubcap tool 2 The presence of the tools depends on This tool is used to remove the wheel the vehicle.
Page 232: Wheel Trims
WHEEL TRIMS Wheel trim with concealed Wheel trim 3 Central wheel trim with wheel bolts visible wheel bolts Remove using hubcap tool 1 (located in (Wheel trim 4) the tool kit) by engaging the hook in the Remove the wheel trim using hubcap opening near the edge of the trim.
Page 233: Changing A Wheel
CHANGING A WHEEL (1/2) Vehicles equipped with a jack Place the jack 4 horizontally; the jack head must be lined up with the sill 1 and wheelbrace closest to the wheel concerned, as If necessary, remove the hubcap. shown by arrow 2. Use the wheelbrace 3 to slacken off Crank up the jack 4 by hand at first to the wheel bolts.
Page 234 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Vehicle fitted with a tyre pressure loss warning system Fit the emergency spare wheel on the central hub and turn it to locate the In the event of under-inflation (punc- ...
Page 235: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
Page 236 TYRES (2/3) Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure tyres are cold; ignore higher pressures loss warning system Adhere to the tyre pressures (including which may be reached in hot weather In the event of under-inflation (punc- the emergency spare wheel).
Page 237 TYRES (3/3) Changing wheels around Use in winter “Snow”or “Winter” tyres We would recommend that these be This practice is not recommended. Chains fitted to all four wheels to ensure that For safety reasons, fitting snow your vehicle retains maximum adhe- Emergency spare wheel chains to the rear axle is strictly for- sion.
Page 238: Headlights: Changing Bulbs
HEADLIGHTS: changing bulbs (1/2) Direction indicators Turn the bulb holder 2 a quarter of a turn and take out the bulb. Type of bulb: PY21W. To comply with current legislation, or Dipped beam headlights Main beam headlights as a precaution, you can obtain an emergency kit from your approved Remove cover A.
Page 239 HEADLIGHTS: changing bulbs (2/2) Before carrying out any action in the engine com- partment, you must switch off the ignition. ➥ 2.3. Daytime running light, front LED side light 4 Please see an authorised dealer. Any operation on (or mod- ification to) the electrical system must be performed by an approved dealer...
Page 240: Fog Lights: Changing Bulbs
FOG LIGHTS: changing bulbs Any operation on (or mod- ification to) the electrical system must be performed by an approved Dealer since an incorrect connection might damage the electrical equipment (harness, components and in par- ticular the alternator). In addition, your Dealer has all the parts re- quired for fitting these units.
Page 241 BACK AND SIDE LIGHTS: changing bulbs (1/3) Direction indicator lights, Release the light assembly from out- 4 Brake light side the vehicle by pulling towards the Bulb type 4 : P21W. brake and side lights rear. 5 Indicator light Undo bolt 1 to remove the light. Remove the bulb holder 3 by releasing Bulb type 5: PY21W.
Page 242 BACK AND SIDE LIGHTS: changing bulbs (2/3) LED 8 side lights High-level brake light Bulb type 10 : P21W. Consult an approved dealer. Remove the nut 9 and release the Refitting brake light from its housing. To refit, proceed in the reverse order, taking care not to damage the wiring.
Page 243 BACK AND SIDE LIGHTS: changing bulbs (3/3) Number plate light Indicator lights 13 Undo screw 11. Unclip indicator light 13 (using a flat- blade screwdriver or similar). Remove the light cover 12 to access the bulb. Turn bulb holder 14 a quarter of a turn and take out the bulb.
Page 244 INTERIOR LIGHTS: changing bulbs (1/5) Front ceiling light 1 Refitting – Clip the lens 2 on to the bulb holder 3; – Unclip the lens 2 (using a tool such as a flat screwdriver), positioned – clip in the interior lights 1 until the unit at A;...
Page 245: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (2/5) Front map reading lights 6 Refitting (depending on the vehicle) – Clip the lens 7 on to the bulb holder 8; – Unclip the lens 7 (using a tool such – clip in the reading spots block 6 until as a flat screwdriver), positioned the unit clicks;...
Page 246 INTERIOR LIGHTING: changing bulbs (3/5) Rear reading spot 11 Refitting (depending on the vehicle) – Clip the lens 12 on to the bulb holder 13; – Unclip the lens 12 (using a tool such as a flat screwdriver), positioned – clip in the reading spots block 11 until at C;...
Page 247 INTERIOR LIGHTING: changing bulbs (4/5) Glove box light 16 Luggage compartment Remove the bulb concerned. light 18 (depending on the vehicle) Bulb type: W5W. Unclip light 16 using a flat-blade screw- Unclip light 18 (using a flat-blade screw- driver or similar) by pressing on the driver or similar), by pressing on tab 19 tab 17 to move the light towards the to move the light towards the inside of...
Page 248 INTERIOR LIGHTING: changing bulbs (5/5) LED light 22 Release the lens 20 and access the bulb 21. Consult an approved dealer. Type of bulb 21: W5W. The bulbs are under pres- sure and can break when replaced. Risk of injury. 5.26...
Page 249: Fuses
FUSES (1/4) Use the fuse allocation label in the storage compartment to identify the fuses. Certain fuses should only be re- placed by a qualified professional. These fuses are not listed on the label. Only change the fuses represented Fuse box Tweezers 2 on the label.
Page 250 FUSES (2/4) Before carrying out any action in the engine com- partment, you must switch off the ignition. ➥ 2.3. Please note when work- ing close to the engine that it may be hot. The engine cooling fan may also start Fuses in the engine compartment B ...
Page 251 FUSES (3/4) Allocation of fuses (the presence and location of fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation Ì  Horn Seat belt warning   Front window winder, electric front windows Instrument panel   Central door locking Towbar socket Front, rear and luggage compartment accesso- ...
Page 252 FUSES (4/4) Allocation of fuses (the presence and location of fuses depends on the vehicle equipment level) Symbol Allocation yṪ Air conditioning control panel Air conditioning control panel, accessories sock- Ṫ ets, radio  Cigarette lighter  Power-assisted steering  Interface for superstructures ...
Page 253: Radio Frequency Remote Control: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries (1/2) The batteries are available from ap- proved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electri- cal contact. If they need to be replaced, be sure to use the same or equivalent type of bat- tery (consult an Approved...
Page 254 RADIO FREQUENCY REMOTE CONTROL: batteries (2/2) Operating faults If the battery is too weak to ensure cor- rect operation, you will still be able to start and lock/unlock the vehicle ➥ 1.6. Precautions relating to batteries: – keep (new or used) bat- teries out of reach of chil- dren;...
Page 255: Battery: Troubleshooting
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any power consumers The battery charger must be com- (courtesy lights etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 256 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 257: Wiper Blades: Replacement
WIPER BLADES: replacement (1/2) Replacing windscreen wiper To refit – press the tab 3 and slide the wiper blade downwards until the hook 5 blades 2 To refit the wiper blade, proceed in re- on the wiper arm is released (move- verse order of removal.
Page 258 WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in re- verse order of removal. Make sure that the blade is correctly locked in position. Before changing the rear wiper blade, make sure the stalk is in the stop position (deactivated).
Page 259: Towing: Breakdown
TOWING: breakdown (1/2) Steering column unlocking Insert the key in the ignition switch and turn it to the “On” position. Put the lever in neutral. The steering column unlocks, the ac- cessory functions are powered: you can use the vehicle’s lights (direction indicators, brake lights, etc.).
Page 260 TOWING: breakdown (2/2) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. – A vehicle must not be towed if it is not fit to be driven.
Page 261 FITTED AUDIO EQUIPMENT – In all cases, it is very important to follow the manufacturer’s instruc- tions carefully. – The specifications of the brack- ets and wires (available from our network) vary depending on the Radio location 1 If your vehicle is not fitted with an audio equipment level of your vehicle system, it is pre-equipped with: and the type of radio.
Page 262: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
Page 263: Operating Faults
OPERATING FAULTS (1/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
Page 264 OPERATING FAULTS (2/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights Battery terminals disconnected, Retighten them, reconnect them or clean are weak or fail to light up and the...
Page 265 OPERATING FAULTS (3/8) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures; if this is not the cause, have sures, incorrectly balanced or dam- their condition checked by an approved dealer. aged.
Page 266 OPERATING FAULTS (4/8) On the road POSSIBLE CAUSES WHAT TO DO Abnormal white smoke from the ex- In the diesel version, this is not ➥ 2.10. haust. necessarily a fault. Smoke may be caused by particle filter regeneration. In the case of the petrol version, this Reduce the engine speed and avoid is not necessarily a fault.
Page 267 OPERATING FAULTS (5/8) On the road POSSIBLE CAUSES WHAT TO DO Whistling. Roof aerial poorly positioned. Position the aerial. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and Ô contact an approved dealer. ant temperature indicator light comes on in red.
Page 268 OPERATING FAULTS (6/8) Stopped POSSIBLE CAUSES WHAT TO DO The engine cooling fan starts to run This is not necessarily a fault. The after the ignition is switched off. engine cooling fan group may start to run in order to regulate the engine temperature.
Page 269 OPERATING FAULTS (7/8) Electrical equipment POSSIBLE CAUSES WHAT TO DO Direction indicators flashing more Bulb blown. Replace the bulb ➥ 5.19. quickly. The direction indicators do not work. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace or have replaced ➥ 5.27. The headlights do not switch on or off.
Page 270 OPERATING FAULTS (8/8) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced ➥...
Page 271 Section 6: Technical specifications Vehicle identification plates ............Technical Information for the emergency services .
Page 272: Vehicle Identification Plates
VEHICLE IDENTIFICATION PLATES Quote the details given on identifica- 5 GTW (Gross train weight: vehicle tion plate A on all letters or orders. fully loaded, with trailer). The presence and location of the in- formation depends on the vehicle. 6 MPAW (Maximim Permissible Weight) for front axle.
Page 273: Technical Information For The Emergency Services
TECHNICAL INFORMATION FOR THE EMERGENCY SERVICES The QR Code on the A label allows emergency workers using a tablet or smartphone to immediately access the technical information useful for working on the vehicle in the event of an acci- dent. Ensure that the A label is always visible and present on the windscreen as well as the rear screen.
Page 274: Engine Identification
ENGINE IDENTIFICATION Please quote the engine identifica- tion information in area A in all cor- respondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine serial number.
Page 275: Dimensions
DIMENSIONS (in metres) (1/2) Van version 1,488 0,851 2,812 0,730 2,079 4,393 1,811 (1) 1,850 (2) 1,478 (1) unladen, without roof bars (2) unladen, with roof bars...
Page 276 DIMENSIONS (in metres) (2/2) Estate version 1,488 0,851 2,812 0,731 2,079 4,394 1,804 (1) 1,842 (2) 1,478 (1) unladen, without roof bars (2) unladen, with roof bars...
Page 277: Engine Specifications
ENGINE SPECIFICATIONS (1/2) Versions 1.3 TCe 1,6 16V 1.5 dCi Engine type H5Ht K9Kt (see engine plate) Cubic capacity (cc) 1 332 1 598 1.461 Petrol Diesel You must use unleaded petrol with the octane The label located in the fuel filler flap indi- rating stated on the label inside the fuel filler flap.
Page 278 ENGINE SPECIFICATIONS (2/2) Versions 1.3 TCe 1.6 16V 1.5 dCi Engine type H5Ht K9Kt (see engine plate) Cubic capacity (cc) 1 332 1 598 1.461 Only use spark plugs specified for your vehicle’s engine. The type should be marked on a label affixed inside the engine compart- Spark plugs ment.
Page 279: Weights (In Kg)
WEIGHTS (in kg) (1/2) The weights indicated are for a basic vehicle without options: they vary depending on your vehicle’s equipment. Consult an approved dealer. Van version Maximum Permissible All-Up Weight (MMAC) Maximum permissible all-up weight (MMTA) Weights indicated on the vehicle identification plate ➥ 6.2. Gross Train Weight (MTR) Braked Trailer Weight* found by calculating: MTR- MMAC...
Page 280 WEIGHTS (in kg) (2/2) The weights indicated are for a basic vehicle without options: they vary depending on your vehicle’s equipment. Consult an approved dealer. Estate version Maximum Permissible All-Up Weight (MMAC) Maximum permissible all-up weight (MMTA) Weights indicated on the vehicle identification plate ➥ 6.2. Gross Train Weight (MTR) Braked Trailer Weight* found by calculating: MTR - MMAC...
Page 281: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 282: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 283 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 284 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 285 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 286 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 287 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 288: Anticorrosion Check
ANTICORROSION CHECK (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 289 ANTICORROSION CHECK (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 290 ANTICORROSION CHECK (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 291 ANTICORROSION CHECK (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.21...
Page 292 ANTICORROSION CHECK (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.22...
Page 293 ANTICORROSION CHECK (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.23...
Page 294 6.24...
Page 295 ALPHABETICAL INDEX (1/5) bulbs ABS ...............2.25 → 2.29 changing ............5.16 → 5.26 accessories................ 5.40 accessories socket ............3.20 capacity of mechanical components........4.4 additional methods of restraint .......... 1.33 catalytic converter..........2.8 – 2.9, 2.9 additive (reagent)..........1.99 → 1.102 changing a bulb ....... 5.16 → 5.18, 5.22 → 5.26 additive tank capacity ..........1.99 →...
Page 296 ALPHABETICAL INDEX (2/5) driving position front lights settings ............1.20 → 1.25 changing bulbs ..........5.16 – 5.17 driving recommendations ........2.12 → 2.15 front passenger air bag deactivation .....1.52 → 1.54 front seat adjustment ..........1.15 → 1.18 front seats ECO driving ........1.60 → 1.65, 2.12 → 2.15 adjustment ............1.15 →...
Page 297 ALPHABETICAL INDEX (3/5) horn: lights flash ................1.55 adjustment ..............1.87 sounding the horn ............1.55 changing bulbs ..........5.16 – 5.17 hubcap tool ................5.9 fog lights ..............5.18 front ..............5.16 – 5.17 lights ..............1.83 → 1.86 ignition switch ..............2.2 lights: indicators ................
Page 298 ALPHABETICAL INDEX (4/5) rear view camera ............ 2.40 – 2.41 oil change ..............4.6 → 4.8 rear view mirrors ............. 1.81 – 1.82 opening the doors ............1.9 → 1.13 remote control door locking operating faults ..........2.49, 5.42 → 5.48 batteries ............5.31 – 5.32 remote control door locking unit .........
Page 299 ALPHABETICAL INDEX (5/5) ventilation .............. 3.2 – 3.3 tailgate ..............3.28 – 3.29 ventilation ........... 3.2 – 3.3, 3.8 – 3.9 technical specifications ....... 6.2, 6.5 – 6.6, 6.11 telephone ..............3.34 – 3.35 warning buzzer ..............1.84 temperature regulation ..........3.8 – 3.9 warning lights............1.60 →...
Page 302 à999108614Së ú ë ä 02 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault EXPRESS 2021 Vehicle User Manual

Section 1: Getting to Know Your Vehicle

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Section 6: Technical Specifications

Quick Links

Chapters

Related Manuals for Renault EXPRESS 2021

Summary of Contents for Renault EXPRESS 2021

Table of Contents